New manufacture solid-state replacement 4 pin vibrators. These replace our old line of solid state vibrators. 1-1/2 dia. x 2-¾" high aluminum can. Replace your buffer capacitor when you replace your vibrator!

L78L33 3.3V regulator in a TO-92 package. The L78L33 three-terminal 3.3V positive regulator employs internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78L series used as Zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise. Features:

• Output voltage of 3.3V
• Output current up to 100 mA
• Short-circuit protection
• No external components are required

KA-193 wallwart power supply. For use with PX4, PX4B and PXR4.

• Voltage: 4.5VDC
• Current: 500mA
• Tip positive; Sleeve negative

This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.

• Voltage: 9VDC
• Current: 200mA
• Tip positive; Sleeve negative

Russian made reissue of the original Tungsol. The Ultimate 12AX7. Big, warm, and musical. High Gain, ultra-low microphonics, and superb linearity with a dynamic 3-D sound. Available with gold pins.

This Russian tube is full bodied and bright with a more straightforward presentation. It packs a lot of bite with its higher-than-normal gain. In overdrive, it offers a lot of crunchy fizz. High gain preamplifier tube with ultra low noise and detailed, musical tone. Unique spiral filament eliminates filament to cathode induced hum common on amplifiers that use AC on the filaments.

The Tube Amp Doctor premium selected 12AX7 / ECC83-Cz features big, warm, clean sounds with a mellow top-end when pushed to overdrive. It’s a great choice for guitar amps and HiFi alike. The ECC83-Cz is recommended if you want to emphasize punchy mids and is especially great when pushed into a fat overdrive. The TAD™ ECC83-Cz is a miniature, high-mu twin triode with good gain, round deep bass, somewhat compressed mids and very smooth top end. Selected and recommended for guitar amps to smoothen up the tone or for HiFi to shape the body of sound more to “that” tube tone. Best for jazzy and thick clean as well as for vintage bass response. Recommended for all positions in amps with medium gain level or High-Gain Amps for V2+ positions. As for V1 in general but especially for higher gain amps or phono/audio-amps, we recommend the RT030 7025/E83CC Highgrade, T-7025-HG-TAD.

The Tube Amp Doctor 7025 / E83CC Highgrade is the premium selection of the RT003 ECC83-Cz for V1 positions. This tube works exceptionally well in the V1 position of high gain amps, combo amps, and phono/audio-amps. The Tube Amp Doctor 7025 / E83CC Highgrade is a miniature, high-mu twin triode with good gain, round deep bass, somewhat compressed mids and very smooth top end. Selected and recommended for guitar amps to smoothen up the tone or for HiFi to shape the body of sound more to “that” tube tone. Best for jazzy and thick clean as well as for vintage bass response. The TAD™ 7025 / E83CC Highgrade can replace any 7025, 12AX7WA, 12AX7WB, 12AX7LPS, 12AX7EH, ECC83 or E83CC.

The FatKeys™ SSI2130 Voltage Controlled Oscillator provides beautiful triangle, sawtooth, pulse, and square waveforms with unprecedented temperature stability; and adds an on-chip mixer, low distortion sine wave generator, through-zero FM/PM capability and more in an ultra-compact PCB footprint.

Superior medium-Mu Twin Triode for use in preamplifier and driver circuits. Standard replacement for all circuits requiring 12AU7/ECC82 types.

3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.

The AS3080E is Alfa’s version of the CA3080 IC. The AS3080E is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080E has differential input and a single-ended, push-pull, class A output. Amplifier bias
input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080E is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.

Totally Tweed! The preferred OEM tube of '50s-era Fender Tweed Champ and Deluxe amplifiers The Tungsol 6V6 has a geometry designed to safely handle the higher voltages used in guitar amps " plus heavier plate and grid materials. The result.. better mids and bottom while keeping the smooth top of the classic 6V6's. The Tungsol 6V6 breaks up evenly from low E to high up the neck. Blues players will LOVE these tubes for the way they sing!

The FatKeys™ SSI2131 Voltage Controlled Oscillator provides the core VCO function with buffered triangle, sawtooth, and variable-width pulse waveform outputs over a ten-octave range. The device offers unparalleled temperature stability, exponentiality, waveform integrity, and ease of use while requiring an absolute minimum of external components. The SSI2131 is a new-generation voltage controlled oscillator for high-performance electronic musical instruments and other systems requiring accurate audio-band waveform generation. The device offers unprecedented levels of temperature stability, exponentiality, waveform integrity, and ease of use.

Superior medium-mu twin triode driver tube for hifi use. 3.5 watts dissipation per plate. New design of excellent quality

The new Tube Amp Doctor premium selected 12AX7 /ECC83-WA is a low-noise and low microphonic version of the 12AX7. The ECC83-WA Premium Selected has a balanced tone with a notable emphasis of the mids. The overall linear sound offers great string attack and chord separation. The low end is well defined. The result is a tone that works well in both modern amps but also vintage guitar amplifiers. If the ECC83-WA is used in hi-fi audio amplifiers, the tube adds a musical clarity and presence to the signal. The new TAD™ ECC83-WA is a miniature, high-mu twin triode, selected and recommended for guitar amps to improve overall responsiveness and dynamics. Great for guitar clean tones with a distinct pick attack and pronounced upper mids to cut through every mix. Crunchy tones still feature a very good string separation which is also ideal for fully saturated sounds and modern amplifiers with a tight bass response.

Screw mounted charge pump PCB for positive ground effects. This small PCB provides -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The PCB has a low profile design and is a simple addition to any build using a standoff to mount the board. This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.

The Sovtek 6550WE was designed to be the finest 6550 ever produced. Thicker plates, improved heat dissipation, higher transconductance, and increased linearity are just some of the inherent aspects of the new Sovtek super 6550s. The resulting performance advantages include 5% higher output power, increased reliability, greater headroom, and superior tone. The 6550WE features a metal-ringed base for increased power-handling capabilities.

The Spin Semiconductor FV-1 is a complete reverb solution in a single IC. With integrated stereo ADC and DACs, the FV-1 can be treated like any other analog component in your product's signal path. The FV-1 can access a total of 16 programs, 8 are built into the internal ROM and the designer may elect to connect a serial EEPROM with 8 additional programs. By using an external EEPROM, the designer can distinguish his product from others by creating a custom program set without the need for a microprocessor in the system. With 3 potentiometer inputs, programs may have real time variable parameters such as decay time in a reverb, rate and depth in a chorus or frequency in a filter. These inputs are available as coefficients to your program and may be used independently of each other. The rich instruction set allows users to program effects of all kinds. With instructions like LOG and EXP, users can easily program audio expansion and compression routines.

The second of two legendary SSM filter updates, the FatKeys™ SSI2144 is a dedicated four-pole low-pass ladder filter with on-chip resonance control. Original designer Dave Rossum did a number of performance updates such as lower noise, improved control feedthrough, and logical pin grouping but otherwise left this sweet-sounding VCF alone. The SSI2144 reprises the SSM2044 of legacy chipmaker Solid State Micro Technology, which many believe to be the best-sounding analog synthesis filter IC ever produced. Based on Dave Rossum’s patented classic improved ladder topology, the SSI2144 allows rich tonal characteristics that showcase the very best attributes of subtractive synthesis. The SSI2144 uses the same internal circuit as the SSM2044 but incorporates improvements by the original designer and takes advantage of modern process technology.

LM358 dual op amp in an 8-pin DIP package. These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V (3 V to 26 V for the LM2904), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage. Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational amplifier circuits that now can be implemented more easily in single-supply-voltage systems.

Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the Power-All® ECO-Dapter® 9 VDC power supply to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices (actual number of units depends on current draw of individual units used).

Electro-Harmonix 6973 Power Tube Beam power amplifier used in vintage Gretsch and Magnatone amplifiers. This is a real 6973, not a rebrand of a "close" tube.

Metal frame AA battery holder. This battery holder fits two AA batteries and is a great option for electronics that run on 3V. It features two solder lugs for connecting wires to the positive and negative ends. The battery holder in the original FZ-1 fuzz pedals looks nearly identical to this holder.