Item Unavailable
Sorry! You are trying to check out one of our items which is no longer available. Why not check out one of these alternate options?
Transformer - Hammond, Radiola III-A Replacement Audio
Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Key Features
Key Features
- Primary: 4000 turns, #41 wire (lugs 4 & 2)
- Secondary: 12000 turns C.T., #41 wire (lugs 5 & 1lug 3 is C.T. connection)
- Termination: Solder lugs on a 1 3/4" x 1" terminal board with 4-5" connecting leads
- Size: 1-7/8" long x 1-11/16" wide x 1-3/8" deep
- Lamination Core Size: 5/8" x 1/2"
- Weight: 7 oz.
$67.70
Transformer - Hammond, Output, replacement for Fender
- Replacements for Fender Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $33.95
Transformer - Reverb Driver, for Fender® Amps, 125A20B Replacement
Replacement reverb driver transformer for the Fender® part numbers 125A20B, 022921, and 037099. This is the standard reverb driver transformer used in most Fender amps that use a 12AT7 and transformer driven 4AB3C1B tank. Found in countless Fender® models including original and reissues of the following:
- Fender Princeton Reverb
- Fender Deluxe Reverb
- Fender Vibrolux Reverb
- Fender Pro Reverb
- Fender Super Reverb
- Fender Twin Reverb
- Fender Quad Reverb
- Fender Super Six Reverb
- Fender Vibrosonic
- Many others
$13.95
Transformer - Hammond, Guitar Amplifier, replacement for Fender, 120 V
Warning: Not all amplifier models of the same name use the same transformer model.
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers
Warning: Not all amplifier models of the same name use the same transformer model.
Starting at $57.49
Filter Choke - Hammond, Open Bracket
Features
- Economical "open bracket" - channel mount.
- Tolerance of 15% on both inductance & resistance.
- Inductances measured at rated D.C.
Starting at $16.75
Transformer - Output, 5W, 5k & 8k Primary Options, Upgrade for Fender® Champ
Output transformer upgrade for the Fender® part numbers 125A35A, 125A3A, and 022905 as used in the:
This upgraded transformer features both 4 ohm and 8 ohm taps on the secondary. The primary has two impedance options for lower voltage (5K) and higher voltage (8k) models.
- Bronco (AA764, AB764, Blackface, Silverface)
- Champ (Tweed, 5C1, 5E1, 5F1, AA764, Blackface, Silverface, Vibro Blackface)
- Harvard (6G10)
- Princeton (Tweed, 5B2, 5C2, 5D2, 5E2, 5F2, 5F2A)
This upgraded transformer features both 4 ohm and 8 ohm taps on the secondary. The primary has two impedance options for lower voltage (5K) and higher voltage (8k) models.
$19.95
Transformer - Output, 8 W, Single Ended
Specifications
- Power: 8 W
- Primary Impedance: 5,000 Ω single-ended
- Secondary Impedance: 8 Ω
- Primary DC Resistance (Red to Blue): 230 Ω
- Mounting Centers: 2.375"
- Mounting Type: U-bracket
- Weight: 0.7 lbs
$20.85
Transformer - Audio Interstage, 10 mA
Equivalent to Stancor A53-C. 1:3 ratio overall. Center tapped secondary may be used for push-pull grids.Specifications Max. Primary Current: 10 mA Impedance Primary to Secondary (Ohms): 10,000 to 90,000
$16.95
Transformer - Hammond, High Voltage Plate & Filament, Vertical mount
- Vertical Mount. For Horizontal Mount, see P-T263-Z
- Primary 115 VAC, 60 Hz. - except as noted
- Enclosed, 4 hole, chassis mount.
- Minimum 6" long leads.
- Units can be run full wave bridge or full wave C.T.
- Class A insulation (105 degrees C).
- Hi-Pot test of 2,000V RMS.
- Conservative designs - CSA certified (209651).
Starting at $69.95
Choke - 4H, 50mA, for Fender® 6V6 Amps, 125C3A Replacement
Replacement choke for the Fender® part numbers 125C3A and 022707 as used in the Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb, 1964 Blackface 6G15 Reverb, and others. This choke is rated 4H 50mA DC.
$11.95
Choke - 4H, 90mA, for Fender® 6L6 Amps, 125C1A Replacement
Replacement choke for the Fender® part numbers 125C1A, 022699, and 036468 as used in the Bandmaster, Dual Showman, Pro Reverb, Twin Reverb, Super Reverb, and others. This choke is rated 4H 90mA DC.
$18.95