Pedal Parts / DIY

The PadBoard-2 prototyping circuit board has a general purpose pad-per-hole pattern which is good for analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. Features

• Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
• Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
• 31 x 39 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
• Size2 = 100 x 80mm (3.94 x 3.15in), 1/16" thick (1.6mm)

Magnifier with 2 ½" lens. Both clamps and magnifier can be removed. Great for precision work on circuit boards, solders and repairs. 6 ball joints for any angle. Simple to adjust thumb screws. Nickel plating fittings. Sturdy iron cast base. Alligator spring clips

1590B diecast enclosure finished in a hammered green powdercoat. 4.40" x 2.38" x 1.06" deep body. 1.22" with lid. Equivalent to Hammond P-H1590B.

• 4.40" x 2.38" x 1.06"
• Hammered green powdercoat
• Die-Cast Aluminum
• Includes Box, Lid, And Screws
• Similar to Hammond P-H1590B
• Add 0.16" to enclosure depth for lid.

Part of a limited run of hammered green enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-GN 1590N1/125 P-H1590N1CE-HMT-GN 1590BB P-H1590BBCE-HMT-GN YY P-H-YY-HMT-GN

PCB for converting SMD SOIC-28-Wide packages to through hole DIP-28 footprints with 0.6" width (wide DIP). Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.

A semiconductor device which passes current in the forward direction(from anode to cathode), and blocks current in the opposite direction. Features

• Silicon epitaxial planar diodes
• Low power loss, high efficiency
• Low leakage
• Low forward voltage
• High speed switching
• High current capability
• High reliability

Used in a variety of Fender amps. Replacement for Fender part number 0006260049

Carling submini toggle switch, SPDT, 2 position, .195" mounting hole diameter, 0.236" bushing length.

2 tip HID (High Definition), non-insulated, metal bushing. Please note that this does not include nuts or washers. Please see parts S-HRVNT S-HRVLW, and R-VNUT-38 if you require them.

Slotted dress nut for ⅜”-32 threaded bushing such as standard Switchcraft ¼” jacks and CTS potentiometers. These plated brass nuts add a sleek look to any amplifier, pedal or guitar. This style of nut has a similar look to slotted round nuts found on plexi Marshall amps.

100kΩ dual-gang 16mm potentiometers with a solid shaft and a linear taper. These pots have right angle PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
• Lead Distance from shaft center: 16 mm (0.630”)
• Lead Thickness: 0.5 mm (0.020”)
• Shaft Diameter: 6.35 mm (0.25”)

5mm (T-1 ¾) diffused LED’s. Great for use in pedal builds and other applications where a tinted and diffused indicator is needed. Multiple colors available.

• 5mm size
• Tinted and diffused
• Multiple colors available
• Package of 5

A semiconductor device that, above a certain reverse voltage(the zener value) has a sudden rise in current. If forward biased, the diode is an ordinary rectifier. When reverse biased, it exhibits a sharp break in its current-voltage graph. Voltage across the diode remains essentially constant for any further increase of reverse current.

New-old-stock Soviet silicon diodes KD522B (КД522Б) in a SOD27 package. These diodes were used in EHX/Sovtek Big Muff models from Civil War to Black Russian. The KD522B is a high-speed switching diode encapsulated in hermetically sealed, leaded glass. The SOD27 packages are similar to DO-35.

1N4742A 12V zener diode in a DO-41 package. A semiconductor device that, above a certain reverse voltage(the zener value) has a sudden rise in current. If forward biased, the diode is an ordinary rectifier. When reverse biased, it exhibits a sharp break in its current-voltage graph. Voltage across the diode remains essentially constant for any further increase of reverse current.

The LM13700 series consists of two current controlled transconductance amplifiers, each with differential inputs and a push-pull output. The two amplifiers share common supplies but otherwise operate independently. Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD. High impedance buffers are provided which are especially designed to complement the dynamic range of the amplifiers. The output buffers of the LM13700 differ from those of the LM13600 in that their input bias currents (and thus their output DC levels) are independent of IABC.

Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the Power-All® ECO-Dapter® 9 VDC power supply to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices (actual number of units depends on current draw of individual units used).

Large MXR knob with set screw for MXR pedals. Original Dunlop replacement part. Skirted knob with white line and dot indicator.

Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet.

RC4558 dual op amp in an 8-pin DIP package. The RC4558 device is a dual general-purpose operational amplifier, with each half electrically similar to the µA741, except that offset null capability is not provided. The high common-mode input voltage range and the absence of latch-up make this amplifier ideal for voltage-follower applications. The device is short-circuit protected, and the internal frequency compensation ensures stability without external components. Features

• Continuous Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• No Frequency Compensation Required
• Low Power Consumption
• No Latch-Up
• Unity-Gain Bandwidth: 3 MHz Typ
• Gain and Phase Match Between Amplifiers
• Low Noise: 8 nV/√Hz Typ at 1 kHz

Applications

• DVD Recorders and Players
• Pro Audio Mixers

Quad low-power opamps in an 14-pin DIP package. The LM324 offers a 1MHz bandwidth and can be powered from a single supply.

A semiconductor device which passes current in the forward direction(from anode to cathode), and blocks current in the opposite direction. For extreme fast switches.

CD4017B is a 5-stage Johnson counter having 10 decoded outputs, respectively. Inputs include a CLOCK, a RESET, and a CLOCK INHIBIT signal. Schmitt trigger action in the CLOCK input circuit provides pulse shaping that allows unlimited clock input pulse rise and fall times. These counters are advanced one count at the positive clock signal transition if the CLOCK INHIBIT signal is low. Counter advancement via the clock line is inhibited when the CLOCK INHIBIT signal is high. A high RESET signal clears the counter to its zero count. Use of the Johnson counter configuration permits high-speed operation, 2-input decode-gating and spike-free decoded outputs. Anti-lock gating is provided, thus assuring proper counting sequence. The decoded output are normally low and go high only at their respective decoded time slot. Each decoded output remains high for one full clock cycle.

Prewired steel low-profile LED bezel with a diffused LED. With a 0.061” height, this steel LED bezel has an almost flush appearance on the panel it’s mounted to. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12VDC. Mounting nut and rubber o-ring included.

Small plastic control knob with set screw and brass insert. This knob features a radial-brushed metal top, a fine straight-knurl grip, and a vertical pointer. Fits ¼” (6.35mm) pot shafts.

Ergonomically designed. Uses one 9V battery, included.

• 0.5% basic DC accuracy
• audible continuity test
• 3 1/2 digit LCD, 0.625" high
• 10M ohm input resistance
• 1.5" x 3" x 7.5"(w/o rubber case)
• overload protection
• voltage to 1000VDC, 750VAC
• capacitance to 20 microfarads
• polarity indicator
• frequency to 10MHz
• over range indicator
• 10A (AC or DC)
• low battery indicator
• hFE and diode test
• tilt stand and case