Pedal Parts / DIY

TL064 quad op amp in a 14-pin DIP package. The JFET-input operational amplifiers of the TL06x series are designed as low-power versions of the TL08x series amplifiers. They feature high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents. The TL06x series features the same terminal assignments as the TL07x and TL08x series. Features

• Very Low Power Consumption
• Typical Supply Current: 200 µA (Per Amplifier)
• Wide Common-Mode and Differential Voltage Ranges
• Low Input Bias and Offset Currents
• Common-Mode Input Voltage Range Includes VCC+
• Output Short-Circuit Protection
• High Input Impedance: JFET-Input Stage
• Internal Frequency Compensation
• Latch-Up-Free Operation
• High Slew Rate: 3.5 V/µs Typical

Audio taper (log), right angle, Alpha pots with a 6.35mm shaft diameter. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.

The NJM2120 is a dual operational amplifier of 2-INPUT and 1-OUTPUT with analog switch. The NJM2120 can be used as analog switch under the condition of GV=0dB, as Switch + Amp in order that each gain (A or B) can be adjusted independently. Each amplifier of the NJM2120 has the same electrical characteristics as the NJM4558. The NJM2120 is suitable for audio, video, electrical musical instrument, etc.

CD4027B is a single monolithic chip integrated circuit containing two identical complementary-symmetry J-K flip flops. Each flip-flop has provisions for individual J, K, Set, Reset, and Clock input signals. Buffered Q and Q signals are provided as outputs. This input-output arrangement provides for compatible operation with the CD4013B dual D-type flip-flop. The CD4027B is useful in performing control, register, and toggle functions. Logic levels present at the J and K inputs along with internal self-steering control the state of each flip-flop; changes in the flip-flop state are synchronous with the positive-going transition of the clock pulse.

Prewired cone-shaped LED bezel. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12VDC. Mounting nut and lock washer included.

Small black plastic control knob with set screw and brass insert. These unique knobs are similar in style to the Davies 1140. They have a thick decorative knurl. A white dot as well as a vertical cutout channel serve as the indicator. Fits ¼” (6.35mm) pot shafts.

Switchcraft Type 12A Littel-Jax shorting type phone jack. The switched terminal is normally closed and is usually connected to ground to eliminate hum when unplugged. Mono 2-conductor. Mates with standard ¼" plugs and is available with standard or long bushings. Includes nut and washer

New old stock radial capacitors from Siemens with 10mm lead spacing. These 0.1uF film capacitors are rated for 250V. The construction matches the style found in vintage equipment such as the MKIII and MKIV Tone Bender pedals.

High-quality USA made knobs from Davies Molding. The large skirted 1550 pointer knob is made of solid phenolic and features a white indicator line. The pointer has an overall length of 1.19” and the skirt’s diameter is 1.13”.

• Height: 0.625 in
• Length: 1.19 in.
• Fits ¼" shaft with set screw

Spring loaded center punch with an adjustable force for aligning pilot holes when drilling into materials. The large handle makes the push-to-strike action simple and accurate. Rotating the red handle adjusts the force amount.

Cry Baby Genuine Replacement Part HI01 Halo Inductor. Used in the famous Clyde McCoy® wah, the Halo Inductor is the key to late ’60s American wah tone. The HI01 delivers that vintage sound, with its expressive sweep and throaty voice, while minimizing microphonic noise due to its stabilized cup-core material.

High quality digitally controlled soldering iron from Atten. The ST-2090D is a 80W benchtop soldering iron with a ton of features packed into its small package. This powerful iron features accurate and adjustable temperature control along and is compatible with a wide variety of tip options. This iron has a built-in dry tip cleaner and an attachable solder spool stand. Conical tip included. Features

• Digital led display
• Combined soldering station with soldering iron and solder wire holder.
• MCU controlled temperature calibration with PID system equipped
• Adjust temperature by knob button, easy to operate.
• The handle structure is ergonomically designed for comfortable grip.
• The heating wire and sensor are made of PTC material, which is quick in temperature rise and precise in temperature control.
• Auto-standby, auto-shut down is available.

Phenolic skirted knobs with set screws and brass inserts. These skirted circular knobs are a close match for the classic knobs used on Fairchild compressors like the 660 / 670. They feature a V-shaped painted inlay indicator on the skirt as well as a dot indicator on the top of the grip. Fits ¼” (6.35mm) pot shafts. Pairs nicely with P-K347-30-X, P-K347-32-X, P-K347-52, P-K347-61 (see photo)

Replacement nut for CTS 450 series potentiometers and others.

• 3/8-32 threading
• Sold individually

DPDT momentary footswitch. AC125V/4A AC250V/2A. Rated for 50,000 make-and-break cycles at full load.

Eddystone 27969PSLA enclosure with similar dimensions to the Hammond 1590A enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590A style builds.

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Aluminum alloy to BS1490, LM2M - supplied in natural finish.
• Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
• Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
• Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
• Countersunk lid holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

PCB for converting SMD TQFP-64 packages to through hole DIP-64 footprints with 0.9" width (wide DIP). Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.

High quality plated ⅜” nuts for jacks and potentiometers. These nuts are perfect for amplifier, pedal and synthesizer builds with high aesthetics or color theming. The ⅜”-32 UNEF-2A threading fits many ⅜” bushing parts such as Switchcraft ¼” jacks and CTS pots.

Genuine Dunlop replacement small knurled knob for MXR pedals. Push -on style knob designed for use with coarse knurled shafts.

Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets.

Dome shaped rubber feet with an embedded 6-32 machine screw. These feet have a 0.4375 inch diameter and have a 0.25 inch screw length. The embedded screw provides a sleek appearance. These are great feet and can also be used as bumpers.

Plastic wing knobs with set screws and brass insert. These knobs are a close match for the classic knobs used on Marconi radios and Neve consoles. They feature an inlay indicator line. The grip diameter is 0.693 inches with a 1 inch clear skirt. Fits ¼” (6.35mm) pot shafts.

Handheld suction type solder remover.

Set screw with brass insert, ¼" shaft. Measures 1.28" diameter x .71" tall.