Pedal Parts / DIY

LT1054 switched-capacitor voltage converter with regulator in an 8 pin DIP package. The LT1054 device is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 can also shut down by grounding the feedback terminal.

Audio taper, vertical mount, dual gang Alpha pots with a 6.35mm shaft diameter. Dual gang pots are useful for stereo controls and other circuits requiring two separate pots moving in tandem. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included. See R-VAV-BX-DUAL for linear taper versions.

The P-K380 is a high quality Davies 1510 clone. This classic design can be found on countless pedals, synths, amps and other equipment. The set screw uses a metal insert for additional stability and durability. This knob has an infilled painted indicator and fits 1/4" (6.35mm) pot shafts. The P-K380 pairs nicely with the color matched P-K801-BRASS-X knobs.

This board is a recreation of the circuit board found in Tone Bender Professional MKII pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKII boards were cut from stripboard, this board follows the same format but is completely ready for soldering with precut traces and drilled mounting holes. The build style is very straightforward on the Mk2. It is a standard stripboard build and follows a very linear circuit path across the board. The traces are gold plated making soldering easier than most stripboards. Additionally the plating provides protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. There are numerous great parts choices available for this PCB.

1.99″ x 1.99″ x 1.22″ (51mm x 51mm x 31mm) diecast aluminum enclosure. Equivalent to the Hammond P-H1590LBX enclosure. This enclosure is great for tap tempos and other utility pedals.

Genuine Cliff™ replacement combination nut/bezel for S4 Series jacks.

• 3/8” thread diameter/20 TPI
• 3/16” thread length
• 7/16” nut
• Used on many Marshall amps
• Matte black finish
• Sold individually.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

1591T Series enclosure made of clear polycarbonate. The 1591C is a similar size to the 1590N1 / 125B diecast aluminum enclosures. Includes four cover screws and pre-installed brass inserts.

• Ideally suited for mounting printed circuit boards.
• Perfect for applications where parts, sensors or indicators need to be visible.
• Crystal Clear version is almost totally transparent.
• Integral card guides accept 1.5 mm (0.062”) P.C. cards.
• Lap joint construction provides protection against access of dust and splashing water.
• Designed to meet IP54.
• Molded from flame retardant, easy to machine, translucent polycarbonate (material carries a UL flammability rating of 94V-2).
• Lid is secured with M3 x 10 mm Phillips machine screws, threaded into integral brass bushings.

High-quality USA made knobs from Rogan Corp. These extra large, puck-shaped, skirted pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm D-shafts.

• Height: 0.63 in.
• Diameter:1.25 in.
• Fits 6mm D Shafts
• Indicator on round side of D-shaft

A variety of different sizes are available from the PT Series.

Carling mini-toggle switch, double pole/double throw, PC Pins. ¼" mounting hole diameter. 0.354" bushing length. 3-Position.

Original replacement for Fender® amps. ¼" Stereo Input Jack that has 9 PCB mount terminals.

Black Marshall-style knobs with a silver cap. This is the taller 0.766” version of this knob. The silver cap has no indicator line matching those found on vintage fuzz pedals such as the Supa Fuzz, Tone Bender Professional MKII, Shatterbox, and MKIII and MKIV Tone Benders. Fits ¼" shaft pots using a slotted set screw.

• Height: 0.766 in.
• Top Diameter:0.594 in.
• Bottom Diameter:0.766 in.
• Fits ¼" shaft with set screw

10kΩ dual-gang 16mm potentiometers with a T18 knurled shaft and a linear taper. These pots have right angle PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
• Lead Distance from shaft center: 16 mm (0.630”)
• Lead Thickness: 0.5 mm (0.020”)

Carling mini-toggle switch, SPDT. This switch features a flattened actuator.

• 0.354" bushing length
• 2-Position On/On
• ¼" mounting hole diameter
• Single pole/Double throw (SPDT)
• Solder Lugs

Polyester film dielectric, aluminum foil electrode, copperply leads and epoxy resin coating in inductive type.

• Small size, light weight and low cost
• Dissipation factor is small because the leads are directly welded to electrodes
• Epoxy resin vacuum-dipped enhances the mechanical strength, humidity resistance
• 100 volt rating
• Operating temperature range: -40°C to +85°C.
• Package of 5

Vintage style quality assurance label. This label has an electronic test line for the name of a technician responsible for testing the electronics and a sound test line for the name of a technician responsible for testing the functionality of the device. This sticker is a great way to document quality assurance testing with a professional presentation on the chassis of a pedal or amp.

2 to 1 heat shrink tubing variety pack. This pack includes six different diameters ranging from 1/16” to 1/2”. Each piece is 2.5” in length. This set comes in a hard plastic case perfect for sorting and storing heat shrink. Features:

• Resistant to common fluids and solvents
• UL and CSA listed
• UV resistant
• Meets DEF. STAN 59.97
• Meets UL 224, 125°C and CSA C22.2 No. 198.1
• Meets MIL-DTL-23053/5 Class 2 & 3
• Flame retardant (Does not include transparent)
• Seals and protects cable splices and terminations.
• Thin wall tubing

Switchcraft shouldered hex nuts for ⅜”-32 UNEF-2A threaded bushings. These nuts include a rubber grommet for use in sealed systems and also add a unique look to any build such as pedals or amplifiers. The large nut (W-SC-DRESS-1) is intended for panel or chassis thicknesses of 0.05” through 0.09”. The small nut (W-SC-DRESS-2) is intended for panel or chassis thicknesses of 0.095” through 0.125”. Rubber grommet included.

Alpha Mini Pots with solid shaft and long PC mount terminals.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
• Lead Distance from shaft center: 16 mm (0.630”)
• Lead Thickness: 0.5 mm (0.020”)

This AC adapter powers several older models of Dunlop pedals, which required a 3.5 mm, or 1/8”, plug as opposed to the 5.5mm x 2.1mm barrel plug required by current models.

• Voltage: 9VDC
• Current: 200mA
• Tip positive; Sleeve negative

Four conductor Flexstrip ribbons cables. These ribbons feature a nomex insulator so there are no melting issues when soldering. Unlike typical ribbon cables, the wires are designed to distribute the stress of the bend and vibrations throughout the entire cable rather than directly on the solder joints. These cables are a great choice for PCB to PCB connections in pedals, synths, and other electronics. The spacing is .1" (2.54mm).

LM318 single op amp in an 8-pin DIP package. The LM318 is a precision, fast operational amplifier designed for applications requiring wide bandwidth and high slew rate. They feature a factor-of-ten increase in speed over general-purpose devices without sacrificing dc performance. These operational amplifiers have internal unity-gain frequency compensation. This considerably simplifies their application because no external components are necessary for operation. However, unlike most internally compensated amplifiers, external frequency compensation may be added for optimum performance. For inverting applications, feed-forward compensation boosts the slew rate to over 150 V/µs and almost double the bandwidth. Overcompensation can be used with the amplifier for greater stability when maximum bandwidth is not needed. Further, a single capacitor can be added to reduce the settling time for 0.1% error band to under 1 µs.

High quality, radial leaded, aluminum electrolytic capacitors rated at 25VDC.

AML387 incandescent light bulb, T-1 3/4 midget flanged, miniature lamp. Great replacement for Morley.