[Skip to content]

Effect Pedals & Parts

  • Sort:
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • View All (10 pages)
Footswitch, 3PDT blue
Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. High quality, made in Taiwan.
More Details
$6.95
Bumper, Rubber, Self Adhesive (Package of 20)
7/16" dia. x 5/32" high.
More Details
$5.00
Footswitch, DPDT for switching and effects, made in Taiwan
Good stomp-box effects switch (Double Pole, Double Throw)
More Details
$3.95
Footswitch, Carling DPDT for switching and effects
Good stomp-box effects switch (Double Pole, Double Throw)
More Details
$8.50
Battery Clip - 9 Volt (Package of 3)
Package of three.
More Details
$0.60
Footswitch - DPDT (Latching), PC Mount
DPDT footswitch, PC mount, same switch as P-H497 but made in Taiwan and PC mount.
More Details
$3.95
Footswitch - Carling, Replacement for Fender® & Others, SPST
Carling SPST footswitch. Used in Fender etc. Reverb/tremolo/channel switching pedals, (110-P).
More Details
$5.95
Footswitch - Carling, DPDT, (On-On)
Carling, DPDT footswitch (on-on) with solder lugs.
More Details
$10.95
Footswitch - DPDT, Momentary, Solder Lugs
DPDT momentary footswitch. AC125V/4A AC250V/2A
More Details
$3.95
Footswitch - Triple Pole, Double Throw (3PDT), Blue, PC Mount
3PDT, PC mount, generic.
More Details
$7.95
Footswitch - Carling, SPDT
Carling SPDT footswitch used in footswitch boxes and effects pedals (112-P).
More Details
$7.15
Switch - Replacement for Boss Effects Pedals
Replacement for Boss effects pedals, SPST momentary, push switch. Mounts in square hole approximately.55" x.55" x 1.08" overall length including terminals.
More Details
$2.50
Footswitch - Carling, SPST, Momentary, Off-On, Normally Open
Carling, SPST footswitch, momentary (off-on), normally open with solder lugs.
More Details
$7.95
Footswitch - DPDT, Momentary, with PC Terminals
DPDT, PC mount
More Details
$4.25
Switch - Dunlop GCB-95
GCB-95 switch. Original Crybaby part for all Crybaby models. Original Dunlop replacement part.
More Details
$9.50
Footswitch - Carling, SPST, Momentary, ON-(OFF) Normally Closed
Carling footswitch, SPST, momentary ON-(OFF) normally closed with solder lugs.
More Details
$7.95
Footswitch - Carling, SPST, Momentary, Off-On, Normally Open
Carling, SPST footswitch, off-on, normally open with screw terminals.
More Details
$6.95
Potentiometer - Wah Pot 100K
100K Wah pot
More Details
$8.95
Potentiometer - Hot Potz II Crybaby, 100K
Hot Potz II Crybaby Pot. for newer Crybaby models. Made by Beckman. 100K ohm. Original Dunlop replacement part.
More Details
$19.95
Potentiometer - Hot Potz 470K
Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470K ohm. Original Dunlop replacement part.
More Details
$19.95
Potentiometer - Wah Replacement, Life Potentiometer - Smooth 100K
100K Life Pot is a high grade Wah pot replacement. This wah pedal upgrad is sold with all necessary hardware and gear for immediate installation.
More Details
$11.95
Knob - Black with Line set screw 1.0" x .6" tall
1.0" diameter x.6" tall, black with white line and brass insert, set screw. Similar to Dunlop knob.
More Details
$1.30
Potentiometer - Wah Pot 125KL
125K linear Wah pot.
More Details
$8.95
Potentiometer - Wah Pot 200KL
200K linear Wah pot.
More Details
$8.95
Potentiometer - Wah Pot Replacement for Ibanez 16mm Dual 500K/50K Linear
500K/50K dual wah replacement for Ibanez WH10. Rated Power: 0.2 Watt max
More Details
$3.95
Potentiometer - Wah Pot 150KL
150K linear Wah pot.
More Details
$8.95
Potentiometer - Dunlop, Wah Pot 20K for Bass
Dunlop 20K pot for the 105Q Crybaby Bass Wah.
More Details
$19.95
Knob - Dunlop, Cover for P-ECB-130
Knob cover for Original MXR knob (P-ECB-130). Original Dunlop replacement part.
More Details
$1.65
Knob - Dunlop
Original MXR knob for Dunlop pedal. Original Dunlop replacement part.
More Details
$2.95
Jack - Dunlop Instrument Stereo Jack
Stereo jack for Dunlop effects pedals. Original Dunlop replacement part.
More Details
$3.35
Chassis Box - 110mm x 58mm x 30mm
4.39" x 2.34" x 1.06" D. Equivalent to Hammond 1590B.
More Details
$5.95
Inductor Fasel Troidal Model (Red), Dunlop
This precision-wound toroidal will give the cleanest sound possible. Use the cup core model, part number P-ECB-FI-01 for a more vintage sound. The Fasel inductor is back! These near-mythical inductors are the key to the singing tonal sweep every wah player lusts for but can't capture with a new pedal. The ultimate upgrade to your current wah, these magic bullets are available exclusively from Dunlop, the new worldwide agent for Fasel of Italy. Your wah will finally give up the lush harmonic sparkle you've always heard in your head but could never coax from you rig.
More Details
$12.75
Chassis Box - Made in Taiwan, Diecast Aluminum
Same as Hammond 1590BB but a generic manufacture from Taiwan. 4.7" x 3.7" x 1.18" depth.
More Details
$8.95
Chassis Box, Die-Cast Aluminum, Black
Cool chassis box perfectly suited for effects pedals and other DIY projects. 4.67" x 3.68" x 1.18" Die-Cast Aluminum Includes Box, Lid, And Screws Painted Black
More Details
$9.25
Chassis Box, Die-Cast Aluminum, Red
Cool chassis box perfectly suited for effects pedals and other DIY projects. 4.67" x 3.68" x 1.18" Die-Cast Aluminum Includes Box, Lid, And Screws Painted Red
More Details
$9.25
Inductor Fasel Cup Core Model (Yellow), Dunlop
This yellow cup core version is best for attaining a vintage vibe. Use the precision-wound Toroidal, part number P-ECB-FI-02, for the cleanest sound possible. The Fasel inductor is back! These near-mythical inductors are the key to the singing tonal sweep every wah player lusts for but can't capture with a new pedal. The ultimate upgrade to your current wah, these magic bullets are available exclusively from Dunlop, the new worldwide agent for Fasel of Italy. Your wah will finally give up the lush harmonic sparkle you've always heard in your head but could never coax from you rig.
More Details
$12.75
Chassis Box, Die-Cast Aluminum, Purple
Cool chassis box perfectly suited for effects pedals and other DIY projects. 4.67" x 3.68" x 1.18" Die-Cast Aluminum Includes Box, Lid, And Screws Painted Purple
More Details
$9.25
Chassis Box, Die-Cast Aluminum, Orange
Cool chassis box perfectly suited for effects pedals and other DIY projects. 4.67" x 3.68" x 1.18" Die-Cast Aluminum Includes Box, Lid, And Screws Painted Orange
More Details
$9.25
Chassis Box - 119mm x 60mm x 40mm
Equivalent to Hammond 1590N1. Measures 4.77" x 2.60" x 1.39".
More Details
$6.25
PC Board - Crybaby
Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.
More Details
$21.95
Chassis Box, Die-Cast Aluminum, Green
Cool chassis box perfectly suited for effects pedals and other DIY projects. 4.67" x 3.68" x 1.18" Die-Cast Aluminum Includes Box, Lid, And Screws Painted Green
More Details
$9.25
Box - Hammond, Unpainted Aluminum, 3.64" x 1.52" x 1.06" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$6.65
Box - Hammond, Unpainted Aluminum, 4.37" x 2.37" x 1.22" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$7.60
Grommets - Dunlop, Offset, 3 Large, 3 Small
Offset grommets. 3 large, 3 small, for Wah.
More Details
$2.50
Chassis Box - Made in Taiwan, Diecast Aluminum, Pre-drilled
Same as Hammond 1590BB, but generic manufacture made in Taiwan. Measures 4.67" x 3.68" x 1.18" deep. Holes are drilled for pots, footswitch and jacks. Holes are 1 @ 1/2" dia., 2 @ 3/8" dia, and 2 @ 8 mm dia.
More Details
$9.95
9-volt digital power supply, Power All System
The PA-9 Power-All is the world's first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don't waste money on batteries or take up valuable space with multiple "wall wart" adaptors or power bricks - the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The PA-9S Power-All Single Kit features: Power-All 9 VDC, 2000 milliamp digital power supply Power all your pedals from a single power supply Takes up only one outlet space
More Details
$17.95
Box - Hammond, Unpainted Aluminum, 4.67" x 3.68" x 1.18" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$9.85
Kit, Power All System deluxe for effects pedals
The Power-All Deluxe Kit provides 9 volts DC at 2000 milliamps @ more than enough current to power dozens of effect pedals, including up to 4 Line 6 Modelers! The Power-All Deluxe Kit can power eleven pedals out of the box, and comes complete with a variety of jumper cables that allow connection of phone plug, reverse polarity, digital, and battery-only pedal types. New Ten-Foot, 18-gauge output cable allows for longer power runs without the need for an extension cord. The PA-9D Power-All Deluxe Kit features: Power-All 9 VDC, 2000 milliamp digital power supply
More Details
$39.95
Chassis Box - 110mm x 58mm x 30mm, Black
4.39" x 2.34" x 1.06" D. Equivalent to Hammond 1590B, black finish.
More Details
$7.95
Box - Aluminum, Unpainted, 7.38" x 4.70" x 2.05" D, Hammond
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Six 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$18.15
Chassis Box - Made in Taiwan, Diecast Aluminum, Pre-drilled
Same as Hammond 1590BB, but generic manufacture made in Taiwan. Measures 4.67" x 3.68" x 1.18" deep. Holes are drilled for pots, footswitch and jacks. Holes are 1 @ 1/2" dia., 2 @ 3/8" dia, and 1 @ 8 mm dia.
More Details
$9.95
Box - Aluminum, Unpainted, 4.72" x 3.70" x 2.07" D, Hammond
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$11.10
Battery Box - Dunlop
Dunlop battery box for Cry Baby and Volume Wahs.
More Details
$1.50
Box - Hammond, Black Aluminum, 4.67" x 3.68" x 1.1" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Painted with tough polyester powder paint for a lasting finish, even after machining. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions.
More Details
$12.80
Bottom Plate for GBC-95 with Battery Door
Bottom Plate with Battery Door for GCB-95. Original Dunlop replacement part.
More Details
$11.75
Rack for Wahs, Dunlop
Rack for Wah.
More Details
$1.95
Photo Cell for Morley Effects Pedals
Photo cell for morley effects pedals.
More Details
$2.50
Gear for Dunlop Wah
Gear for Dunlop Wah.
More Details
$1.95
Box - Hammond, Unpainted Aluminum, 5.3" x 4.4" x 1.5" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$12.45
Box - Hammond, Unpainted Aluminum, 1.99" x 1.99" x 1.06" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$6.85
Inductor, 500mH
500mH inductor for all Crybaby models. Original Dunlop replacement part.
More Details
$11.50
Rubber feet with screws
Rubber feet with screws for Dunlop Crybaby Wah pedal. Package of four. Original Dunlop replacement part. Rubber foot diameter: 5/8" Rubber foot height: 5/16" Screw threading: #6-32 (screw extends 5/16" beyond the rubber surface)
More Details
$2.50
Box - Hammond, Unpainted Aluminum, 7.38" x 7.38" x 2.48" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Six 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions.
More Details
$26.05
Box - Hammond, Unpainted Aluminum, 5.3" x 4.4" x 2.2" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$13.70
Box - Hammond, Unpainted Aluminum, 4.77" x 2.6" x 1.39" Depth
Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.
More Details
$10.35
Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 3.07" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Six 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions.
More Details
$19.40
Footswitch - Dunlop, DPDT, PC Mount, for MXR
DPDT, PC mount footswitch for MXR.
More Details
$14.25
Box - Hammond, Unpainted Aluminum, 4.70" x 4.70" x 3.54" Depth
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x ½" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting. Dimensions shown are exterior dimensions. Add 0.16" to enclosure depth for lid.
More Details
$20.80
Rack for Wahs, Generic
Replacement rack for wahs.
More Details
$1.25
Adapter - AC Plug, 9 Volt, US
AC Adapter. Plug type. 9 volt. US. Original Dunlop replacement part.
More Details
$11.75
AC Adapter Barrel, 9 Volt, US
AC Adaptor. Barrel type. 9 Volt. US. Original Dunlop replacement part.
More Details
$11.75
Bulb - Morley Effects Pedals Replacement
Replacement bulb for Morley effects pedal.
More Details
$0.95
Battery Holder - 4 "AA" Cells
Battery holder for four AA cells. Overall Outer Length x Width = 4 3/16" x 1
More Details
$0.20
Enclosure - Wah Pedal Shell and Hardware
Wah pedal enclosure, bottom, and foot-pedal shell and hardware
More Details
$40.00
Gear - For Wah Pot
Gear for potentiometers in wah pedals.
More Details
$1.50
  • Sort:
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • View All (10 pages)