Switches

Switch - Rotary, Voltage Selector, Modern, for Marshall
  • Ratings:
    • IEC: 6.3 A / 250 VAC; 50 Hz
    • UL: 10 A / 250 VAC; 60 Hz
    • CSA: 8 A / 250 VAC; 60 Hz
  • Mounting: Panel Mount from front side
  • Fastening: Screw-on mounting
  • Terminal: Solder
  • Number of Stages: 3
  • Type: SP3T
  • Lifetime: 300 operating cycles (without load)
  • Degree of Protection: IP 40
  • Allowable Operation Temp.: -40 °C to 85 °C
  • Climatic Category: 25/85/21 acc. to IEC 60068-1
  • Material of Socket: Thermoplastic, black, UL 94V-0
  • Weight: 16.5 g
  • Solderability: 350 °C / 2 sec acc. to IEC 60068-2-20, Test Ta, method 2
  • Resistance to Soldering Heat: 350 °C / 10 sec acc. to IEC 60068-2-20, Test Tb, method 2
  • Insulation Resistance: > 10,000MΩ (500VDC; 1min)
  • Contact Resistance: < 10 mΩ at 20 mV
  • Dielectric Strength:
    • > 2.5kVAC between L-N (1min; 50Hz)
    • > 4kVAC between L/N-PE (1min; 50Hz)
  • Clearance and Creepage Distance:
    • > 5mm
    • > 8mm between L/N-PE
  • Resistance to Vibration: acc. to IEC 60068-2-6, test Fc
$35.45
Switch - Rotary, Impedance Selector, Replacement for Marshall
Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side. SP3T.
$34.95
On Backorder
Switch - Rotary, Impedance Selector, 3 Position
Rotary impedance selector, 4/8/16. Body screws onto chassis hole. SP3T switch.
$16.95
Switch - Marshall, Toggle, DPST, On-Off, Chrome Tip
Marshall toggle switch, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. See Marshall nut S-HM300N if necessary. Nut sold separately. Note: On-Off switches may sometimes be referred to as On-None-Off.
$15.95
Switch - Toggle, DPST, On-Off, Chrome Tip
Toggle switch for Marshall amps, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. Mounting nuts (1 hex and 1 knurled) included. Main features:
  • Construction : Terminal and contact support are manufactured from a single piece of metal. The contacts are resistance-welded to the terminal for increased mechanical strength.
  • Rating : These switches are suitable for motor loads and power applications up to 15A 250VAC
  • UL, CSA and NF-VDE (EN 61058-1) approved

Note: On-Off switches may sometimes be referred to as On-None-Off.
$14.95
Switch - Selector, Vintage Style, for Marshall, Male
Vintage style selector switch male part, replacement for Marshall.
$12.95
Switch - Rotary, 1 Pole, 3 Position
High quality three position rotary switch commonly used as an impedance selector switch on tube amps. This rugged switch is rated for 6A at 125VAC and 3A at 250VAC. The flatted 6mm shaft can be used with the shaft adapter found in the accessories below to easily fit standard ¼” knobs. Mounting hardware included. SP3T.
$12.95
Switch - Rocker, Lighted Power, Used in JCM Series & Others
Lighted DPST On-Off power switch. Used in Marshall JCM series and others. 15/16" x 1-1/16" x 1" deep.
$12.50
Switch - Carling, Toggle, SPST, Ball Actuator
Heavy duty Carling SPST (Single Pole, Single Throw) toggle switch with a vintage-style ball actuator. This latching On-Off switch is a great option for vintage amps and electronics or new builds with vintage styling. Rated for 3A 250V, 6A 125V, AC/DC.
$9.45
Switch - Rocker, Standby for JCM Series & Others, Black
For Marshall™, JCM series and others. 15/16" x 1 1/16" x 1" deep. DPST On-Off switch,
$7.95
Switch - Fender®, Toggle, SPST, Standby, Solder Lugs
Original Fender®, Carling SPST On-Off toggle switch for Fender tube amps - 3A, 250VAC; 6A, 125VAC, ½" mounting hole. Commonly used as the power switch.
$6.95
Switch - Marshall Style, Rocker, Power for MG Amps, Black
Marshall style black On-Off rocker switch for MG amps. 0.51" x 0.76" Mounting Hole. DPST.
$6.55
Switch - Carling, Toggle, SPDT, 2 Position, for Fender®
1A, 250V; 3A, 125V. Carling SPDT 2 position On-On toggle switch. Great Fender ground switch replacement.
$6.45
Switch - Carling, Toggle, SPST, Replacement for Fender®
Fender® style power and/or standby switch (Single Pole, Single Throw). This latching On-Off switch is a great replacement for older Fender® amps where the shorter toggle length (1/2”) is desired.
$5.95
Switch - Black Bat, Toggle, 4PST, Vintage Marshall Style, Solder Lugs
Black bat toggle switches with a similar style to the Arrow and Torotor switches found on many vintage Marshall amps. This 4PST switch is rated for 230VAC, 4.5A. Includes one hex nut and one knurled nut.
$5.50
Switch - Carling, Mini Toggle, SPDT, 3-Position, PC Pins
Carling mini-toggle switch, single pole/double throw, PC Pins. ¼" mounting hole diameter. 0.354" bushing length. 3-Position, On-Off-On.
$5.45
Switch - Switchcraft, Slide, DPTT, 3-Position
Genuine Switchcraft® DPTT 3-position slide switch for use on Mustang and Duosonic style guitars. This switch can be wired to operate in either On/Off/On or On/On/On configurations. Upgrade cheap or malfunctioning switches with these high quality replacements.
  • Recommended .75 control cavity depth
  • 1.406” center-to-center mounting hole spacing
  • #4-40 screws recommended for mounting
  • Screws not included
$5.35
Switch - Carling, Toggle, SPST, On-Off, Side Solder Lugs
Carling, 2 position, On-Off, SPST with solder lugs, 1/2" mounting hole. Note: On-Off switches may sometimes be referred to as On-None-Off.
$5.15
Switch - Black Bat, Toggle, DPST, On-Off/On-Off, Vintage Marshall Style, Solder Lugs
Black bat toggle switches with a similar style to the Arrow and Torotor switches found on many vintage Marshall amps. This On-Off SPST switch is rated for 230VAC, 4.5A. When in the up position, both switches are on. When in the down position, both switches are off. Includes one hex nut and one knurled nut.
$4.95
Switch - Carling, Mini Toggle, SPDT, 3 Position, Solder Lug
Carling mini-toggle switch, SPDT, Solder Lug, 3-Position, On/Off/On
$4.95
Switch - Carling, Submini Toggle, SPDT, 2 Position, PC Pins
Carling submini toggle switch, SPDT, 2 position, .195" mounting hole diameter, 0.236" bushing length.
$4.95
Switch - Switchcraft®, Slide, DPDT, Jazzmaster / Jaguar
Genuine Switchcraft® DPDT 2-position On-On slide switch for use on Jazzmaster and Jaguar style guitars. Also used for bright switches in Fender black and silverface amplifiers. Upgrade cheap or malfunctioning switches with these high quality replacements.
  • Recommended .75 control cavity depth
  • 1.125” center-to-center mounting hole spacing
  • Latching
  • Screws not included
  • See S-HS440-12 for compatible screws
$4.45
Switch - Black Bat, Toggle, DPST, On-Off/Off-On, Vintage Marshall Style, Solder Lugs
Black bat toggle switches with a similar style to the Arrow and Torotor switches found on many vintage Marshall amps. This DPST switch is rated for 230VAC, 4.5A. When in the up position, the top switch is on and the bottom switch is off. When in the down position, the top switch is off and the bottom switch is on. Includes one hex nut and one knurled nut.
$4.35
Switch - Carling, Mini Toggle, DPDT, 3 Position
Genuine Carling DPDT 3 Position Mini Toggle, Round Bat, Solder Lugs
  • DPDT ( Double Pole/ Double Throw) switch
  • 0.354" bushing length
  • 0.409” bat length
  • ¼" chassis hole diameter
  • Solder terminals
Starting at $4.15