 | Digital Capacitance Meter Nine ranges give precision readings from 0.1 pF to 20,000 µF. Can be used to check virtually all capacitors for tolerance value, selecting matched sets, etc. 0.1 pf to 20,000 μF, 9 ranges Over range indicator 0.5% basic accuracy Tilt stand 3-1/2 digit LCD, 1" h x 2-1/4" w 1.5" x 2.8" x 6" Zero adjustment 1.1 lbs Input protected Low battery indicator Includes case, leads, battery, spare fuse and instructions | $39.95 More Details |
 | Bias and Matching Meter, Alessandro After all is said and done, few components are as critical to the quality of your sound as your power tubes. In short, improperly balanced and biased tubes can wreak havoc with your amp's overall performance, and more importantly with your sound. | $144.95 More Details |
 | Test Lead, Set, Military Specification Contains: 2 alligator clips, 2 spade lugs, 2 pin jacks (long), 2 pin jacks (short), 2 probe tips, 2 tip insulators and 2 universal test jacks. All have threaded male ends. Also contains two 54" leads with female threaded ends. All parts are rolled up in a convenient pouch. Sealed in foil military package. The ultimate set of test leads! | $8.95 More Details |
 | Digital Multimeter Ergonomically designed. Uses one 9V battery, included. 0.5% basic DC accuracy audible continuity test 3 1/2 digit LCD, 0.625" high 10M ohm input resistance 1.5" x 3" x 7.5"(w/o rubber case) overload protection voltage to 1000VDC, 750VAC capacitance to 20 microfarads polarity indicator frequency to 10MHz over range indicator 10A (AC or DC) low battery indicator hFE and diode test tilt stand and case 1.6 lbs. | $44.95 More Details |
 | Analog Multimeter - Volt-Ohm-Millimeter Intermagnetic version to prevent interference from magnetic fields. Double protection of diode and fuse, transistor hFE test function. DCV: 0.25V, 0.5V, 2.5V, 10V, 50V, 250V 1000V. ACV: 10V, 50V, 250V, 500V,1000V. DCA: 50 uA, 2.5 mA, 25mA, 250mA. Ohms: x1, x10, x1k, x10k. Dimensions: 148mm x 98mm x 41mm | $15.95 More Details |
 | Generator - Audio Frequency The oscillation frequency range of this audio generator is between voice frequency band and super voice frequency band. Square and sine wave. 10K ohm input impedance, 10 V rms maximum input voltage. 600 ohm output impedance. Equipped with synchronized input terminals, enabling the high power output signas to be accurately controlled by small signals. comes with test lead and ground lead. 5.9" high x 9.8" wide x 5.1"deep. 8 lbs. Features: High frequency stability: within ± 2Hz Frequency range - 10 Hz ~ 1 MHz, 5 decade bands Accuracy = 10Hz ~ 1 MHz - ± 5% + 2Hz | $150.00 More Details |
 | Generator - RF Signal Compact solid state RF signal generator designed for the hobbyist, service bench and technical instruction. The generator is most suitedfor checking and aligning the IF circuit and tuners in AM, FM, and TV's. 100KHz to 150MHz in 6 bands and up to 450MHz on third harmonics. 5.9" high x 9.8" wide x 5.1" deep. Features: Wide frequency range- 100 Khz to 150 MHz With 1 KHz oscillator purpose of modulation High Stability Output control- 0dB/-20dB/-40dB and fine adjuster Frequency accuracy + or - 5% RF output- 100mV rms appx. (up to 35MHz unloaded) Output control- High-low switch, fine adjust | $150.00 More Details |
 | Bias King Pro As tubes age, their bias point will shift. By using the BIAS KING™ you can maintain the sound you want by periodically adjusting the bias on your own amp. This will keep your tubes in top shape throughout their life and will keep your amp sounding its best. Use the chart provided to find out what range of current flow is acceptable for the tube type in your amp. It works on most octal socket tube amps, and requires no power source other than the amp it's plugged in to. It can also be used to match tubes into pairs. | $189.95 More Details |
 | Jumper Test Lead Set - Clip 35mm, Total Length 24", 22AWG Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green | $3.95 More Details |
 | Signal Tracer Handy, easy-to-operate versatile instrument with dual power source (9V battery or AC adapter). Two red LEDs on front panel indicate the mode of operation. Ideal for servicing on TV, AM and audio circuitry, plus checking of speakers, microphones, and pick-ups. 100 microamp meter, 2 ¼" speaker 7.8" W x 5.5" H x 3.9" D. Tracer Portion Features: Gain- Max. 60 dB at 1 KHz Attenuation: 0-20-40-60 dB Input impedance: 100K ohms RF output: 100mV rms appx (up to 35MHz unloaded) Output impedance: Output-600ohms(unbalanced)ext.speaker 8 ohms Injection Portion Features: | $140.00 More Details |
 | Bias King As tubes age, their bias point will shift. By using the BIAS KING™ you can maintain the sound you want by periodically adjusting the bias on your own amp. This will keep your tubes in top shape throughout their life and will keep your amp sounding its best. Use the chart provided to find out what range of current flow is acceptable for the tube type in your amp. It works on most octal socket tube amps, and requires no power source other than the amp it's plugged in to. It can also be used to match tubes into pairs. | $119.95 More Details |
