You are here

Transformers & Chokes

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(26 pages)
P-T166M2P-T166M2Item ID: 003469Transformer - Hammond, Filament, 2.5 VCT, 3 A
Primary 115 VAC, 60 Hz · Center tapped secondary · Open style, channel bracket, two hole chassis mount · Minimum 6" long leads · Dual bobbin design - no electrostatic shield required · Class B insulation (130 degrees, C) · Hi-Pot test of 2,000 V RMS · UL listed (# E50394) & CSA certified (# LR3902) · Specifications Rating: 2.5 VCT, 3 A Mounting Centers: 2-3/8", u-bracket
Read More...
$13.85
$12.47
P-T272FXP-T272FXItem ID: 003527Transformer - Hammond, Power, 300-0-300 V, 150 mA
Dual primary 115 VAC, 125 VAC, 60 Hz. · Secondary DC current measured with cap. input filter, full wave (two diode) C.T., rectifier circuit. · Enclosed, 4 hole chassis mount. · Minimum 6" long leads. · Class A insulation (105 degrees C). · Hi-Pot test of 2,000 V RMS. · Conservative designs - CSA certified (# LR3902). · Secondary: 300-0-300 V, 150 mA Filament winding 1: 5 V, 3 A CT Filament winding 2: 6.3 V, 5 A CT Mounting centers: 2.5" x 2.19" vertical mount Weight: 5 lbs.
Read More...
$81.27
$73.14
P-T158LP-T158LItem ID: 003442Filter Choke - Hammond, Open Bracket, 15 H, 75 mA
Specifications Rating: 15 Henries, 75 mA Max. VDC: 400 Resistance: 411 ohms Mounting centers: 2.81" u-frame Weight: 1.3 lbs. Economical 'open bracket' - channel mount. · Tolerance of 15% on both inductance & resistance. · Inductances measured at rated D.C. current. · Minimum 5" long leads. · Units will exhibit less inductance at slightly higher currents or more at lower currents. · Perfect for high voltage power supply filtering. ·
Read More...
$21.85
$19.67
P-T261G6P-T261G6Item ID: 003508Transformer - Hammond, Power, Low Voltage, 250V CT @ 130 mA
Dual primary 115 VAC, 125 VAC, 60 Hz. · Designed for small power or bias supplies, test equipment, preamps etc. · Economical , 2 hole channel bracket, chassis mount. · Minimum 5" long leads. · Secondary: 250 VCT, 130 mA Filament winding: 6.3 V, 2 A Mounting centers: 3.56" u-bracket Weight: 2 lbs.
Read More...
$40.77
$36.69
P-TF22905P-TF22905Item ID: 003591Transformer - Fender® Replacement, Output, 8 W, 3.2 Ohm
Replacement for Fender Champ, VibroChamp, and Bronco amps, 4 ohms. Equivalent to #125A35A & #022905. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
Read More...
$32.95
$29.66
P-T118944P-T118944Item ID: 005565Transformer - Radiola III-A Replacement Audio, Hammond
Developed in response to requests from RCA Radiola III-A collectors. The original transformers are usually found with open" windings due to the fine wire and high turns usedcoupled with age. This is a universal replacement type - it will replace any of the three audio transformers used (1st audio driver2nd audio-phase splitter stage or output transformer)by correctly connectiong the 5 lugs. A pin out and connection diagram is included. The cases from the old transformer will fit this new unit. The terminal board is a duplicate of the original.
Read More...
$42.15
$37.94
P-T431P-T431Item ID: 005610Transformer - Audio Interstage, Coil Assembly for P-T156
Coil assembly for P-T156. Use your own iron to preserve mechanical fit. Coil window is 1/2 x 1/2".
Read More...
$14.75
$13.28
P-C194AP-C194AItem ID: 002042Choke - Hammond, Replacement for Fender
Equivalent to 022707, 125C3A 50mA/167 ohms. for Deluxe, Vibrolux, stand alone reverbs, late Tremolux. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
Read More...
$16.30
$14.67
P-T125AP-T125AItem ID: 003426Transformer - Hammond, Universal Push-Pull, 3 W, 25 mA
Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits). · Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz). · Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections. · Tables provided with transformer listing 90 pre-calculated impedance ratios.
Read More...
$35.25
$31.73
P-T125CSEP-T125CSEItem ID: 003430Transformer - Hammond, Universal Single Ended, 8 W, 60 mA
Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits. · Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE). · For push-pull output use, see P-T125A - optimized for push-pull tube output circuits. · Open style with minimum 12" long primary & secondary leads leads. · All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C. core saturation.
Read More...
$47.69
$42.92

Pages

(26 pages)
Subscribe to RSS - Transformers & Chokes