You are here

Transformers & Chokes

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(37 pages)
P-T193LP-T193LItem ID: 003502Filter Choke - Hammond, Enclosed, 5 H, 300 mA
Specifications Rating: 5 Henries, 300 mA Max. VDC: 800 Resistance: 57 ohms Mounting centers: 2.4375" x 2.5" vertical mount Weight: 5.5 lbs. Enclosed, 4-hole mounted chokes. · Tolerance of 15% on both inductance & resistance. · Inductances measured at rated D.C. current. · Minimum 8" long leads. · Units will exhibit less inductance at slightly higher currents or more at lower currents. · Perfect for high voltage power supply filtering; case matches Hammond power transformers & tube audio output transformers. ·
Read More...
$69.23
P-C194EP-C194EItem ID: 002046Choke - Hammond, Replacement for Vox
For AC30 vintage.
Read More...
$46.55
P-TM800-CP-TM800-CItem ID: 003615Filter Choke - Genuine Marshall, for JCM800
Genuine Marshall™ filter choke. for JCM800.
Read More...
$49.95
P-C194DP-C194DItem ID: 002045Choke - Hammond, Replacement for Vox
For AC30 reissue.
Read More...
$46.55
P-T290EXP-T290EXItem ID: 003547Transformer - Hammond, Power, Replacement for Fender, 120 V
Equivalent to 125P7D and 022814 for Bassman, Concert, Pro (no filament CT). Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
Read More...
$80.12
P-RC-2P-RC-2Item ID: 003281One Electron Audio Choke PRC-2, 12/48H for Shunt Feed SE Output
The PRC-2 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes. It uses the same high quality M6 laminations as the UBT transfomers. Has two identical windings allowing series and parallel combinations. It is not recommended for use as a transformer. The table shows the maximum recommended load impedances when used as a shunt-feed choke. As with traditional class-A triode amplifiers, the driving impedance is about 1/2 the load impedance.
Read More...
$69.95
P-T269EXP-T269EXItem ID: 003514Transformer - Hammond, Power, 190-0-190 V, 65 mA
Dual primary 115 VAC, 125 VAC, 60 Hz. · Secondary DC current measured with cap. input filter, full wave (two diode) C.T., rectifier circuit. · Enclosed, 4 hole chassis mount. · Minimum 6" long leads. · Class A insulation (105 degrees C). · Hi-Pot test of 2,000 V RMS. · Conservative designs - CSA certified (# LR3902). · Secondary: 190-0-190 V, 65 mA Filament winding: 6.3 V, 2.5 A Mounting centers: 1.75" x 1.56" vertical mount Weight: 1.8 lbs.
Read More...
$45.91
P-TM-P50P-TM-P50Item ID: 003610Transformer - Marshall Replacement, Power, 50 W
50 watt power transformer. Built to vintage specs with exact interleave ratios and materials. A good upgrade for later issue Marshall amplifiers. Good replacement for JMP and JCM 800s. for EL34! Mounting centers are 3.25" x 3.25"
Read More...
$86.95
P-T159MP-T159MItem ID: 003445Filter Choke - Hammond, Open Bracket, 15 H, 100 mA
Specifications Rating: 15 Henries, 100 mA Max. VDC: 500 Resistance: 256 ohms Mounting centers: 3.56" u-frame Weight: 2.25 lbs. Economical 'open bracket' - channel mount. · Tolerance of 15% on both inductance & resistance. · Inductances measured at rated D.C. current. · Minimum 5" long leads. · Units will exhibit less inductance at slightly higher currents or more at lower currents. · Perfect for high voltage power supply filtering. ·
Read More...
$27.85
P-T193JP-T193JItem ID: 003500Filter Choke - Hammond, Enclosed, 10 H, 200 mA
Specifications Rating: 10 Henries, 200 mA Max. VDC: 800 Resistance: 82 ohms Mounting centers: 2.4375" x 2.5" vertical mount Weight: 5.5 lbs.
Read More...
$60.00

Pages

(37 pages)
Subscribe to RSS - Transformers & Chokes