Audio. 16mm body size (mini type) Snap-In pot with mounting bracket. Solid Shaft ¼", ⅜" length shaft. 8mm bushing, ¼" bushing length. PC Mount. Nut and washer included.

Mini Carbon Element, Push Pull Switch, Dual Audio, Solid Shaft. 17 mm body diameter. 1/4" watt, 300° rotation. DPDT, 6mm shaft diameter. Solder lugs. 3/8" bushing. Bourns® Model PDB183-GTR21 Guitar Potentiometer with Push-Pull Switch. Used for Split-Coil Pickup Switching Electric guitar manufacturing is a multi-billion dollar industry with major manufacturers established worldwide. From the introduction of the first mass-produced electric guitar in 1950, guitarists have been mesmerized with advances in technology and the wide array of after- market parts commercially available for guitar upgrades. Specialty products such as Bourns® Model PDB183-GTR21 Guitar Potentiometer with Push-Pull Switch allow the guitarist multiple functions utilizing a single control such as split-coil switching for humbucking (double-pole) pickups or stacked single-coil pickups, active electronics activation, and pickup phase switching.

10K dual linear, 16mm, 7mm bushing.

Potentiometer - 500K, Linear, Knurled Shaft, DPDT, Push-Push

• DPDT Push-Push switch
• ¼" split knurled shaft
• Linear taper
• 3/8-32 threads
• 16mm body diameter (widest point on switch body 17.8mm)
• .40" bushing length
• 38"-.52" shaft length.

The HCP Humbucker Control Pot is a dual mode variable coil tap selector for electric guitars and basses that eliminates the additional switches associated with coil splitting a pair of humbuckers. In TAP mode, rotating the pot counterclockwise fades from humbuckers to outer coils (neck pickup South coil & bridge pickup North coil). Pulling the HCP control up and rotating it counterclockwise fades from humbuckers to inner coils (neck pickup North coil & bridge pickup South coil). Tonal control is expanded with the unique ability to coil tap both humbuckers in varying amounts. In COIL FILTER mode, turning the HCP control applies varying amounts of a specially tuned high frequency filter to only one coil of the selected coils of the humbuckers (either North or South coils can be filtered). This makes each pickup a single coil at high frequencies and a humbucker at lower frequencies which produces a sound similar to a pair of single coils but with a stronger, fuller tone and 50% less noise than coil tapping.

Alpha Mini Pots with solid shaft and long PC mount terminals.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
• Lead Distance from shaft center: 16 mm (0.630”)
• Lead Thickness: 0.5 mm (0.020”)

Add a switch to your guitar using the existing holes in your pick guard or body. High quality CTS Push/Pull DPDT switches can be used to add phase switching, coil tapping, series/parallel, etc. to your guitar without having to drill the holes for a mini switch. The shorter body height and side mounted contacts require far less space (1” depth ) making them ideal for thinner bodied guitars with a more shallow body cavity. These Split-shaft pots are compatible with 24- spline, fine knurled knobs and feature a precise audio taper. Hex nuts, flat washer, and lock washer are included with each pot. CTS DPDT pots are available in three types for different applications.

Dual MN taper blend-balance with center detent. Solid shaft. 17 mm body diameter. ¼ watt, 300° rotation. 6mm shaft diameter. Solder lugs. 3/8" bushing.

CTS J Taper audio potentiometer.

• Body Diameter: 24 mm
• Power Rating ⅓ watt
• Bushing Diameter: ⅜" (Threading: 3/8-32)
• Bushing Length: 3/8"
• Shaft Diameter: ¼"
• Shaft Length: ⅜"
• Shaft Material: Brass - Solid Shaft

Genuine Fender® 250K pan pot with center detent. Pan pots are also known as balance pots. Solid shaft (1/4") with 3/8” bushing. Mounting hardware not included. See R-VNUT-38 for a compatible nut and washer.

High quality potentiometers from AxLabs. These audio taper pots feature a ⅜” bushing and coarse (T18) knurled shaft. The dish back style matches the construction of many vintage guitars. Unlike any other potentiometers on the market, AxLabs pots were specifically designed for electric guitars, utilizing years of painstaking attention to detail in the industry. AxLabs potentiometers feature machined brass shaft sleeves and are lubricated with 3 different types of grease used in specific areas of the moving parts for ultra-smooth rotation. Shafts are then reinforced with a retainer ring positio­ned for strength and to reduce friction.

High quality potentiometers from AxLabs. These audio taper pots feature a ¼” bushing and coarse (T18) knurled shaft. The dish back style matches the construction of many vintage guitars. Unlike any other potentiometers on the market, AxLabs pots were specifically designed for electric guitars, utilizing years of painstaking attention to detail in the industry. AxLabs potentiometers feature machined brass shaft sleeves and are lubricated with 3 different types of grease used in specific areas of the moving parts for ultra-smooth rotation. Shafts are then reinforced with a retainer ring positio­ned for strength and to reduce friction.

Linear taper square body PC mount potentiometer by Marshall. Body width = 11mm
See R-VKG-XA for the Audio taper equivalent

Alpha Push-Pull, Solder Lug, 7mm bushing, DPDT, 1/4" solid shaft, audio taper potentiometer.

5kΩ reverse audio taper Alpha 16mm pots with a solid shaft and long PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 20.7 mm + 4 mm (0.815” + 0.158”)
• Lead Distance from shaft center: 14.3 mm (0.563”)
• Lead Thickness: 0.5 mm (0.020”)
• Shaft Diameter: 6.35 mm (0.25”)

Genuine Dunlop replacement potentiometer for wah/volume.

• 10 kΩ Linear
• Gear included

250K ohm, solid shaft. for most Stratocasters and Telecasters. Original guitar hardware. CTS manufactured, includes capacitor. Comes in Fender^® packaging.

The DMT is a passive dual mode guitar tone control designed specifically for electric guitars that can operate in either HIGH PASS or LOW PASS modes greatly expanding the instruments tonal possibilities without the use of a battery or active electronics. Micro switches on the circuit board provide the user the ability to select one of two different frequency ranges for both high and low pass modes. Easy installation with no capacitors or other parts needed. Replace the tone control in you guitar with one that you will actually use!

Push-Pull Solder Lug, 7mm bushing, DPDT, ¼" shaft, linear.

The 24mm body knurled shaft potentiometer features a 1/3 watt rating and a 3/8" bushing. 24 teeth slot and knurled shaft.
Includes:

• 1 nut
• 1 lock washer

Reverse audio taper Alpha 16mm pots with a solid shaft and right angle PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
• Lead Distance from shaft center: 16 mm (0.630”)
• Lead Thickness: 0.5 mm (0.020”)
• Shaft Diameter: 6.35 mm (0.25”)

Audio taper, vertical mount, Alpha pots with a 6.35mm shaft diameter featuring 11 detents across the rotation. The 11 detent versions are useful for builds where 1-10 settings are commonly used or if the pot is used as a rotary switch along with a microcontroller. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included. See R-VAV-BX-11DET for linear taper versions.

Tokyo Cosmos aka TOCOS is known worldwide for their high quality potentiometers. The RV24 Series is a 24mm military-style carbon element potentiometer with a tolerance of 10%. The RV24 Series has been praised by both guitar and hifi amp builders for their performance and reliability. If you are looking for a top quality pot with a great feel, look no further than Tocos. Each audio taper potentiometer includes a nut, flush washer, and lock washer.

• 24mm diameter, single-turn potentiometers
• Carbon film element
• Metal shaft and bushing
• Panel mount
• Ear-lug solder terminals
• 6mm diameter slotted-end solid shaft
• 10mm bushing length
• 10mm shaft length (extended past bushing)
• Audio Taper

10K Reverse Audio with bracket. Mounting hardware not included.