Products
No product page found for product T-17.
Showing search results for T-17
Switch Accessory - Mini Toggle Caps
Rubber caps / switch tips for mini toggle switches in a variety of colors. These are made for standard sized toggle bats.
Colors Available:
Starting at $0.59
Transformer - Hammond, Output, replacement for Fender
- Replacements for Fender Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $33.95
Tuners - Gotoh, GB707, Compact for Bass, 2 per side
Precision 20:1 gear ratio enclosed Bass Guitar tuners. With a 7/16"-diameter string posts and threaded hex bushings. They require a 9/16"-diameter peghole for installation. Featuring sealed lubricated, cast housings and metal knobs. Mounting screws are included. Mounting hardware included.
Colors Available:
Starting at $39.75
package of 4
Cutters - Xcelite, Shearcutter, General Purpose
5" Overall Length, 3/4" Jaw Length. Great for cutting wire and component leads, etc. Product Features:
- Low profile, general-purpose cutter
- Superior blade by-pass shear cutting action
- Better cuts with half the effort
- Greatly reduced mechanical shock delivered to the work
- Features red grips
- Flush cuts soft wire up to 20 AWG (0.8mm)
$15.95
Staking Tool - for Eyelets and Turrets
Turret staking tool for use with our turrets (S-HTUR-SG-2X, S-HTUR-SG-3X, S-HTUR-PR-3S).
For anvil see S-T1717
For smaller staking tool, see S-T1714
Directions:
For anvil see S-T1717
For smaller staking tool, see S-T1714
Directions:
- Drill 1/8" hole
- Insert eyelet
- Flip board over on to a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$14.95
Transformer - Hammond, Output, replacement for Marshall
- Replacements for Marshall Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $49.95
Tool - Anvil for Turret Terminals, .750 L
Turret anvil for use with our turrets (S-HTUR-SG-2X, S-HTUR-SG-3X, S-HTUR-PR-3S).
For staking tool see S-T1715
Directions:
For staking tool see S-T1715
Directions:
- Drill 1/8" hole
- Insert eyelet
- Flip board over on to a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$14.39
Tuners - Gotoh, GB707, Compact for Bass, chrome, 4-In-Line
Precision 20:1 gear ratio enclosed Bass Guitar tuners. With a 7/16"-diameter string posts and threaded hex bushings. They require a 9/16"-diameter peghole for installation. Featuring sealed lubricated, cast housings and metal knobs. Mounting screws are included. Mounting hardware included. For 4-string bass. 4 in a line.
$39.95
package of 4
Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
- Drill hole using #42 drill bit
- Insert eyelet
- Flip board over onto a hard service
- Center staking tool over the eyelet
- Strike staking tool with hammer to clamp eyelet to board
$14.95
Transformer - Hammond, Output, replacement for Vox
- Replacements for Vox Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $91.00
Save 23%
Originally: $118.72
Transformer - Hammond, Output, replacement for Yorkville / Traynor
- Replacements for Yorkville/Traynor Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $61.03
Tuners - Gotoh, GB707, Compact for Bass, chrome, 3+2
Precision 20:1 gear ratio enclosed Bass Guitar tuners. With a 7/16"-diameter string posts and threaded hex bushings. They require a 9/16"-diameter peghole for installation. Featuring sealed lubricated, cast housings and metal knobs. Mounting screws are included. Mounting hardware included. For 5-string bass. 3 Left, 2 Right.
$49.50
package of 5
Transformer - Hammond, Output, replacement for Orange Rocker 30
Hammond output transformer - replacement for Orange Rocker 30 Specifications: Part No. Pri Ohms Sec Ohms Amplifier Type Watts Bobbin/Paper Winding Equivalent To P-T1750ORF 6,000 C.T. 8, 16 Push-Pull 35 W Bobbin OT199SL
$82.23
Transformer - Hammond, Isolation / plug & receptacle
- Primary 115VAC, 50 / 60 Hz., Secondary 115VAC
- Provides complete circuit isolation.
- Electrostatic shield between primary & secondary to greatly attenuate surges and noise.
- Hi-pot tested to 2 KV RMS.
- Circuit breaker in primary.
- Standard 3-wire, grounded plug & receptacle.
- Input (primary) connected to 5 foot long cord & standard North American plug (NEMA 5-15P).
- Output (secondary) connected to 1 foot long "pig tail" cord, 3-wire, standard North American grounded receptacle (NEMA 5-15R).
- North American Mark of Safety - C UL & UL listed (File #E211544)
- Indoor use only
- Remember - These units do NOT convert line frequency
Starting at $122.85
Tuners - Gotoh, GB707, Compact for Bass, chrome, 2+3
Precision 20:1 gear ratio enclosed Bass Guitar tuners. With a 7/16"-diameter string posts and threaded hex bushings. They require a 9/16"-diameter peghole for installation. Featuring sealed lubricated, cast housings and metal knobs. Mounting screws are included. Mounting hardware included. For 5-string bass. 2 Left, 3 Right.
$46.85
package of 5
Transformer - Hammond, Step-Up, 500VA
Capacity: 500VA Features:
- Single winding does not provide isolation, for use where equipment is already isolated and only voltage change is required.
- World wide applications, 50 or 60 Hz.
$186.40
Vacuum Tube - 1T4 / DF91, Pentode, Remote Cut-Off
Miniature remote-cutoff pentode designed for use as a radio-frequency or intermediate frequency amplifier in compact, battery-operated equipment.
$4.90
Vacuum Tube - 3S4 / DL92, Pentode, Power
Filamentary type power output pentode in the miniature construction. It is characterized by economy of filament power and ability to perform well at low plate supply voltages such as encountered in portable equipment.
$4.90
Vacuum Tube - 1R5 / DK91, Heptode
Miniature pentagrid-converter designed for use as a combined mixer and oscillator in superheterodyne circuits. Because of its small size and high operating efficiency, the 1R5 is especially adapted for compact, battery-operated equipment.
$5.90
Vacuum Tube - 1LN5, Pentode (VT179)
Sharp-cutoff pentode designed for use as a radio-frequency, intermediate frequency, or audio-frequency amplifier in battery operated receivers.
$6.25
Vacuum Tube - 1S5 / DAF91, Diode, Sharp Cut-Off Pentode
Miniature tube containing a diode and a sharp-cutoff pentode. It is designed for use as a combined detector and audio-frequency voltage amplifier in compact battery-powered equipment.
$3.55
Vacuum Tube - 1LH4, Diode, Triode
Tube combining a single diode and a high-mu triode in one bulb. It is designed for service as a diode detector, AVC rectifier, and as a resistance coupled amplifier.
$4.90
Vacuum Tube - 1LC6, Heptode
Filament-type pentagrid converter designed particularly for use in low drain battery-operated equipment. This tube will operate satisfactorily with only 45 volts B supply.
$4.90