Amplifier Parts

Fender® style lamp jewels are used on countless amps from all kinds of manufacturers. Threading: 9/16 - 27. Note: When back-lit, the color of the amp jewels will be affected by the color of the bulb behind it.

High quality fuse holder used with 3AG type fuse. Fits in a 1/2" diameter chassis hole. Frame and cap material: phenolic Terminal material: Nickel-plated brass Mounted by nut

Lamp holder. Relampable front panel indicators accept a variety of T-2 and T-3 ¼ miniature bayonet lamps.

• 11/16" chassis hole
• Total Length = 1.755" (solder lugs included in measurement) (extends about 1.68" from front of panel to end of solder lugs)
• Rating: 125V, 75W
• Threading: 9/16 - 27

Available Jewels Amber P-L117 Blue P-L120 Clear P-L122 Green P-L116 Purple P-L121 Red P-L115 Violet P-L121V White P-L123

The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.

High quality Fender® Style fuse holder replacement for guitar amplifiers.

• Fits ½" chassis hole diameter
• Mounted by Nut

Locking terminal lugs, #6 or #8 hole, 5/8" length, angled. Package of 10

Steel 20mm screw nails for corners, logos, badges, and more. These screw nails make adding cabinet accessories easy requiring only a mallet for installation. The design is great for speaker cabinets ensuring a better grip than standard nails and tacks under extreme vibrations.

Turrets for use on boards measuring 3mm thick, such as P-HTUR-189-3BK or P-HTUR-189-3R. For 2mm boards, see S-HTUR-SG-2X
Stake and anvil required for mounting.

• Staking Tool is our part number: S-T1715
• Anvil is our part number S-T1717
• For a budget tool set see S-T-STAKE-SET

Spring steel tooth-lock washer. Uses internal teeth for locking and tension.

18AWG SJT power cords used in many amplifiers along with other appliances and equipment. These cords feature bare ends for hard wiring to devices internally or using a connector. The attached plug is a Nema 5-15P for North American grounded outlets. These cords have a maximum voltage rating of 300V.

#8-32 x 3 ¼" chassis strap screw. Single piece.

Eyelets, bag of 10 (mounts in 1/8" hole).

Popular low-cost lock nut (also known as a Keps nut, k-lock, or washer nut) for commercial and industrial applications. Locking action is achieved when the nut is tightened against a bearing surface as the teeth of the lock washer dig into it.

Corner wraps around inside edge of cabinet. Works on 3/4" of wood + material thickness. Countersunk mount holes, 20 gauge, 1/2" radius. Sold individually. See S-H102 for mounting hardware.

Power Cord / cable - (3 conductor) Bare End, 16 AWG

Phillips panhead machine screw, 6-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

LED version of the general replacement lamps for dials, indicators, etc. Used as the pilot light on the vast majority of Fender amps and many others as well. This LED version can be used to replace either #44 or #47 bulbs (see P-44 and P-47 for incandescent versions). The color options for this LED bulb can be combined with colored jewels to create new and interesting color options! The opaque shell on these LED bulbs provides a clean diffused glow.

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.

Tin plated brass eyelets commonly used on vintage style pickups. The small sized eyelets are also great for smaller point-to-point projects such as DIY stomp boxes. The outside diameter of the barrel is 0.089” and the recommended mounting hole is 0.093” using a #42 drill bit.

Turrets for use on boards measuring 2mm thick. For 3mm boards, see S-HTUR-SG-3X
Stake and anvil required for mounting.

• Staking Tool is our part number: S-T1715
• Anvil is our part number S-T1717
• For a budget tool set see S-T-STAKE-SET

Long life general replacement lamps for dials, indicators, etc. The #47 bulb is the most common replacement light used today. Used on the vast majority of Fender amps and many others as well.

Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.

For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.

• Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
• Securely anchors, insulates, and protects cables at panel entry points

Listed diameter is inside diameter. Sold in packs of 5.

• 3/8" diameter designed for chassis hole with diameter 1/2"
• 1/8" diameter designed for chassis hole with diameter 1/4"
• 3/16" diameter designed for chassis hole with diameter 5/16"
• 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
• 1/4" diameter designed for chassis hole with diameter 7/16"
• 5/16" diameter designed for chassis hole with diameter 7/16"