Amplifier Parts

P-G00X Grommet - Rubber, for chassis holes
Listed diameter is inside diameter. Sold in packs of 5.
  • 3/8" diameter designed for chassis hole with diameter 1/2"
  • 1/8" diameter designed for chassis hole with diameter 1/4"
  • 3/16" diameter designed for chassis hole with diameter 5/16"
  • 1/4", small cutout diameter designed for chassis hole with diameter 3/8"
  • 1/4" diameter designed for chassis hole with diameter 7/16"
  • 5/16" diameter designed for chassis hole with diameter 7/16"
Starting at $1.75
package of 5
P-H1050 Corner - Black Plastic, 4-Hole, Replacement for Vox / Orange
These Tube Amp Doctor black plastic corners are great replacements for certain Vox® amps from 1966 to 2004 and Orange® amps and cabinets that feature this type. The two larger holes are for use with screws while the small holes are intended for pins/nails just like the originals.
$1.35
P-H1080N Corner - Steel, 3-Hole, 18 Gauge, for vinyl/carpeted cabinets
Industry standard 3-leg back side corner cover for vinyl or carpet covered cabinets. 18 gauge steel, 1/2" radius. Sold individually. See S-H101 for mounting hardware.
$1.09
P-H1082N Corner - Steel, 2-Hole, 18 Gauge, Nickel
Use where total material thickness is 1/2" or more. Works on carpet or vinyl, 18 gauge steel, 1/2" radius. Radius is.50" from the center hole to furthermost edge. Sold individually. See S-H101 for mounting hardware.
$1.09
P-H1084N Corner - Steel, 2-Hole, 18 Gauge, ¾" Thickness
Steel, 2-Hole corner. Replacement for Fender® Corner wraps around inside edge of cabinet. See S-H101 for mounting hardware.
  • Works on ¾" of wood + material thickness
  • 18 gauge steel
  • 12mm / ½" radius
  • For Fender®
  • Sold individually.
$1.08
P-H1086N Corner - Steel, 3-Hole, 20 Gauge, for cabinets
11mm / 7/16" Radius, 20 Gauge Steel (Sold individually)
$1.19
P-H1087N Corner - 2-Hole, 20 Gauge, for cabinets
Corner wraps around inside edge of cabinet. Works on 3/4" of wood + material thickness. Countersunk mount holes, 20 gauge, 1/2" radius. Sold individually. See S-H102 for mounting hardware.
$1.09
P-H1090 Corner - Marshall, Black Plastic, 4-Hole, Rear, with rivets
Marshall back corners with gold rivets. 3/4" radius.
For similar generic back corners, see P-H3080.
$6.95
package of 4
P-H1091 Corner - Marshall, Black Plastic, 3-Hole, with rivets
Genuine Marshall front corner set. These corners feature 3/4" radius and three mounting holes. These corners can be used on both straight and slanted cabinets. Includes gold mounting rivets. Sold in package of four corners.
For similar generic front corners, see P-H3081.
$6.75
package of 4
Out of Stock
P-H1092 Corner - Marshall, Black Plastic, 3-Hole, Front Left / Right
Two black plastic, three hole, genuine Marshall® corners for slanted cabinets. Includes one left corner, one right corner and six gold mounting rivets.
For similar generic front corners, see P-H3081.
$9.00
Out of Stock
P-H1095 Corner - Peavey, Black Steel, 2-Hole, Lip
Black metal, 2 hole with lip, radius ½". Sold individually.
$1.50
P-H1097 Corner - Black steel, 2-Hole, 18 Gauge, Notched
2-leg notched, black, wraparound. 18 gauge steel, ½" radius. Sold individually.
$1.65
P-H1098 Corner - Black Steel, 2-Hole, 18 Gauge, Wraparound, Lip
2-leg black, wraparound with lip. 18 gauge steel, ½" radius. Sold individually.
$1.65
P-H1099 Corner - Black Steel, 3-Hole, 18 Gauge
3-leg black, standard. 18 gauge steel, ½" radius. Sold individually.
$1.95
P-H1200 Strain Relief - for ¾" x ~\frac{27}{32}~" hole, ~\frac{5}{16}~" cord diameter
16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.
$1.29
P-H1300 Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, ~\frac{11}{32}~" Cord Diameter
For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.
  • Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
  • Securely anchors, insulates, and protects cables at panel entry points
$0.59
P-H1308 Foot - Rubber, ¼" tall with ½" diameter, countersunk
1/4" tall x 1/2" outside diameter. Interior through hole diameter is 1/8". A counter sunk hole for the screw or nail (not included) is ¼" diameter x 3/16" deep
$3.25
package of 4
P-H1315 Rubber feet - 7/16” Dome Shape, Embedded 6-32 Screw
Dome shaped rubber feet with an embedded 6-32 machine screw. These feet have a 0.4375 inch diameter and have a 0.25 inch screw length. The embedded screw provides a sleek appearance. These are great feet and can also be used as bumpers.
$0.95
P-H1427C1 Handle - Hammond, steel construction, 1427C1
Special Order Item
Round steel handle with 4" mounting hole center. 1.3" tall. Hardware included.
$5.02
Note: special order items require additional lead time. See our page on special order items.
P-H1427N2X Handle - Hammond, Steel Construction, 3.5”, 1427N2
Colors Available:
Round metal handle with 3.5" mounting centers and 1.5" height. These handles are great for amplifiers, rackmount gear, and guitar pedals. Mounting screws and lock washers are included. Features
  • Made of round steel
  • 2 Screws - Panhead 8-32 x 1/2"
  • 2 Internal Tooth Lockwashers
Starting at $5.15
P-H1427Q Handle - Hammond, Steel Construction, 2.25”, 1427Q
Round metal handle with 2.25" mounting centers and 1" height. These handles are great for amplifiers, rackmount gear, and guitar pedals. Mounting screws and lock washers are included. Features
  • Made of round steel
  • 2 Screws - Panhead 6-32 x 3/8"
  • 2 Internal Tooth Lockwashers
$5.65
P-H1427T3 Handle - Hammond, Steel Construction, 5", 1427T3
Round metal handle with 5" mounting centers and 1.5" height. These handles are great for amplifiers, rackmount gear, and guitar pedals. Mounting screws and lock washers are included. Features
  • Made of round steel
  • 2 Screws - Panhead 10-32 x 1/2"
  • 2 Internal Tooth Lockwashers
$5.90
P-H185 Washer - ⅞" x ⅛" Thick, Rubber, Chassis Mount,
Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. 1/4 inner dia. Allows proper dial centering in cabinet opening. Adhesive backing for lamenating to other washers to increase thickness. Overall dimensions 7/8" dia. x 1/8" thick.
$0.65
P-H186 Washer - Rubber, Chassis Mount, ⅞" Diameter
Gum rubber chassis mounting washers as used on thirties vintage Zenith and Philco radio. Allows proper dial centering in cabinet opening. Overall dimensions 0.875" dia. x .233" thick.
$0.75