Analog Multimeter - Volt-Ohm-Millimeter

Item Unavailable

Sorry! You are trying to check out one of our items which is no longer available. Why not check out one of these alternate options?

Digital Capacitance Meter - YF-150, 9 ranges
Nine ranges give precision readings from 0.1 pF to 20,000 µF. Can be used to check virtually all capacitors for tolerance value, selecting matched sets, etc.
  • 0.1 pf to 20,000 μF, 9 ranges
  • Over range indicator
  • 0.5% basic accuracy
  • Tilt stand
  • 3-1/2 digit LCD, 1" h x 2-¼" w
  • 1.5" x 2.8" x 6"
  • Zero adjustment
  • Input protected
  • Low battery indicator
  • Includes case, leads, battery, spare fuse and instructions
$42.95
Digital Multimeter - YF-3220, multi-purpose
Ergonomically designed. Uses one 9V battery, included.
  • 0.5% basic DC accuracy
  • audible continuity test
  • 3 1/2 digit LCD, 0.625" high
  • 10M ohm input resistance
  • 1.5" x 3" x 7.5"(w/o rubber case)
  • overload protection
  • voltage to 1000VDC, 750VAC
  • capacitance to 20 microfarads
  • polarity indicator
  • frequency to 10MHz
  • over range indicator
  • 10A (AC or DC)
  • low battery indicator
  • hFE and diode test
  • tilt stand and case
$44.95
Jumper Test Lead Set - Clip 35mm, Total Length 24", 22AWG
Package of 10
Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green
$4.89
Bias Master™ - TAD, tube tester, with 4 probes
Bias Master™ system BM4 Measures Bias current of the vacuum tubes in your amp. Includes 4 probes and english/german operation manual. The Bias Master™ allows you to monitor the bias current safely and easily. While adjusting the Bias control pot of your amp, the Bias Master™ shows the actual result. This lets you set and evaluate the full reasonable biasing range your amp and tubes offer to find and set your personal perfect choice.
$224.95
Probes - TAD, for Bias Master™, set of 2
Package of 2
Bias Master™ set of adapter probes for testing other types of tubes. For use with the S-TBM4-X Bias Master™ system.
Starting at $71.50
Generator - Lodestar, RF Signal generator
Compact solid state RF signal generator designed for the hobbyist, service bench and technical instruction. The generator is most suited for checking and aligning the IF circuit and tuners in AM, FM, and TVs. 100 kHz to 150 MHz in 6 bands and up to 450 MHz on third harmonics.
Features:
  • Wide frequency range- 100 Khz to 150 MHz
  • With 1 KHz oscillator purpose of modulation
  • High Stability
  • Output control- 0dB/-20dB/-40dB and fine adjuster
  • Frequency accuracy + or - 5%
  • RF output- 100mV rms appx. (up to 35MHz unloaded)
  • Output control- High-low switch, fine adjust
  • Audio output 1 KHz min., 2V rms
  • Modulation: Internal: 1 KHz (AM) 30% appx., External: 50 Hz ~ 20 KHz at <1V rms input
$178.00
Generator - Lodestar, Audio Frequency
The oscillation frequency range of this audio generator is between voice frequency band and super voice frequency band. Square and sine wave. 10K ohm input impedance, 10 V rms maximum input voltage. 600 ohm output impedance. Equipped with synchronized input terminals, enabling the high power output signas to be accurately controlled by small signals. comes with test lead and ground lead. 5.9" high x 9.8" wide x 5.1"deep.
$184.95
Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
$1.75
Solder wick - GC Braid, multiple sizes
5 feet Long. Great for removing solder from printed circuit boards or other electronic equipment.
Starting at $3.50
Tool - Precision Devices, Lead Former, Various Sizes
High quality, made in USA lead formers. These are great tools for bending component leads to fit various footprints. The radiused ends provide a right angle bend that does not stress the metal lead. These lead formers are made of high impact ABS plastic.
$4.95
Fret Puller - Narrow Jaws, for removing frets
A specialized tool for cleanly pulling out frets. The narrow jaws are designed specifically to allow for a clean grip on frets. The special flush ground 1/2" jaws can easily bite the frets without damaging the fretboard.
$7.95
Solder - Kester, 60 / 40, 44 Flux, 1 lb spool
60/40 Rosin Core, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.
Starting at $31.95
Nut File - Edge-Cut, for slotting guitar nuts
Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4.5” cutting edge
  • Double sided (both sides are the same gauge)
  • 10 gauges available
  • Sold individually*
  • Made In Japan

*See S-T213-SET for a set of all 10 sizes.
Starting at $11.50
Soldering Iron Tip - Weller, solid core, screwdriver type, ST Series
Genuine Weller screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The screwdriver style is great for soldering through hole components and many other situations. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
Starting at $4.50
Staking Tool - for Eyelets and Turrets
Turret staking tool for use with our turrets (S-HTUR-AX, S-HTUR-BX, S-HTUR-P).
For anvil see S-T1717
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$9.95
Solder - Kester, 60 / 40, 44 Flux, 66 Core, .031 Dia, .5 oz
Kester 44 60/40 rosin core type. .031" diameter, 0.5 oz
$5.78
Burnishing Tool - GC Electronics, ¼" wide, steel
Stainless steel strip, microscored to an ultrafine file surface. Remove oxide and corrosion on contacts made of platinum, paladium, moybdenum, gold, tungsten, and silver.
$3.50