Circuit Design

Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
$2.50
Solder wick - GC Braid, multiple sizes
5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.
Starting at $5.95
Truss Rod Wrench - Phillips Head / Cross Head
High quality Phillips head truss rod wrench. This Japanese made wrench is the perfect tool for cross slotted truss rod nuts found on many Fender® necks. The compact 9mm diameter head has a thin 11mm width allowing for adjustments without removing the neck
$10.16
Soldering Iron Tip - Weller, hollow core, screwdriver type, ET Series
Genuine Weller screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The screwdriver style is great for soldering through hole components. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$6.50
Staking Tool Set - Anvil and Punch, for Eyelets and Turrets
Staking tool set that includes both the anvil and swage/punch. The set works with standard turret and eyelet sizes commonly used in amplifiers. The anvil also can be used with Y style turrets.
$12.55
Soldering Iron Tip - Weller, screwdriver type, ST Series
Genuine Weller screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The screwdriver style is great for soldering through hole components and many other situations. The flatted tip makes it easy to make contact with both the solder pad and component lead. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
Starting at $6.50
Soldering iron tip - Weller, screwdriver, for WTCPT, 700F
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Screwdriver Tip for TC201 Series Iron
  • PTA7 - 1.6mm / 0.063" diameter screwdriver tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
$6.50
Alignment Tool - Zenith-Admiral Hex Wrench
GC Electronics 8606 alignment tool with hex and special tip slug. This tool is made of non-conductive Delrin.
  • End 1 - 0.027 in.
  • End 2 - 0.1 in.
  • End 3 - 0.1 in.
$1.50
Soldering iron tip - Weller, conical, ST Series
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWP35 and S-TWLC100.
  • ST Series Tips: Will fit the SP40L / SP40N series irons as well as the WP25, WP30, WP35, WLC100 series tools
  • Precision ground copper tips are plated with iron, nickel and chromium
  • ST7 - .031" / 0.79 mm diameter Conical tip
  • Tinned with Lead Free alloy
$6.50
Soldering iron tip - Weller, hollow core, 0.8mm, conical, ET Series
Genuine Weller conical style (round) tips for use with all ET Series compatible soldering irons. The concal style is great for general use and precision soldering on small contacts. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$6.50
Soldering Iron Tip - Weller, hollow core, long screwdriver type, ET Series
Genuine Weller long screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The long screwdriver style is great in situations where additional length is required or for narrow places. These tips are an excellent choice for use with the S-TWE1010 soldering station.
$6.50
Soldering Iron Tip - Weller, hollow core, single flat / sloped type, ET Series
Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$5.95
Sponge - for Soldering Station, for cleaning tips
Replacement sponge for soldering stations. Maintain a clean iron tip with this high quality replacement sponge. Using a damp sponge to clean a hot soldering iron helps the solder contract at a different rate than the iron, effectively removing any excess solder from the tip. Make sure the sponge is damp, not soaked, for optimal cleaning.
$1.95
Desoldering pump tip - Weller, replacement for 7874B
Restore the performance of your desoldering pump by replacing the tip. Replacement for S-T7874B.
$8.95
Soldering iron tip - Weller, conical, for WTCPT
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Conical Tip for TC201 Series Iron
  • PTP7 - 0.79mm / 0.031" diameter conical tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
$5.95
Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$14.95
Soldering iron tip - Weller, hollow core, 1.6mm, narrow screwdriver, ET Series
Genuine Weller narrow screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$6.19
Desoldering Pump - Weller, manual, for removing solder
Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. This lightweight desoldering pump has an anodized aluminium body to assure durability and features a plunger safety shield, short-stroke plunger and a no-clog automatic tip cleaner. Replace tip with S-T7875B. Made in Taiwan.
$35.49
Soldering Iron - Weller SPG80L, 80 watts
The Weller SPG80L is a heavy duty 80 Watt soldering iron. It is ideal for soldering chassis connections in classic amps such as can capacitors and can be used in many other applications. This soldering iron has an indicator light that shows when the iron is turned on for safe use. The barrel is stainless steel and the rugged tip is replaceable. The impact resistant handle remains cool when in use. Features:
  • 900°F tip temperature suitable for chassis soldering and other heavy duty applications
  • Indicator light to show when the iron is on
  • 3/8” chisel tip
  • 6 foot power cord
  • Metal stand included
$49.95
Soldering Iron Tip - Weller, single flat / sloped type, ST Series
Genuine Weller single flat style tips for use with all ST Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
$6.50
Soldering iron station - Weller, WE 1010, 70W, digital display
The Weller WE1010 is an excellent soldering station for professional use and beginner hobbyists alike. With increased power and stability, the WE1010 is an upgrade in many ways for users of the WES51 and WTCPT soldering stations.
$165.95
Soldering Iron Tip - Weller, narrow screwdriver type, ST Series
Genuine Weller narrow screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
$6.19
Seizer Forceps - 5.5" Straight Nose, Serrated Jaws
High quality seizer forceps. These are a great tool for assisting with soldering, wiring and other hardware related tasks. Features
  • Versatile tool with unusual holding qualities
  • Clamps firmly to hold wires for soldering
  • Acts as a heat sink and retrieves small parts from hard-to-reach places
  • Precision-machined from perfectly tempered stainless steel
  • Box-joint construction
  • 3-position snap lock
  • Serrated jaws
$9.95
Soldering Iron - Battery Powered, Portable
This portable battery powered soldering iron is great in a pinch. The small sized iron is a perfect fit in a gig bag or backpack.
$11.99