Circuit Design

Staking Tool - for Eyelets and Turrets
Turret staking tool for use with our turrets (S-HTUR-SG-2X, S-HTUR-SG-3X, S-HTUR-PR-3S).
For anvil see S-T1717
For smaller staking tool, see S-T1714
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$14.39
Solder - Kester 63 / 37, 1 lb spool, 0.031" diameter
(63/37 Rosin Core) - ..031" Diameter, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.
$50.95
StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$8.75
Battery Holder with Connector - 9V, Chassis Mount, Horizontal
High quality chassis mount battery holder with a built-in connector. This clip fits standard 9V batteries. The horizontal mount and small footprint of the holder allows for easy placement where vertical space is limited. The two connections use individual solder tabs for hard wiring directly into projects providing a rugged and stable connection.
$5.45
Battery Box - Gotoh, Dual, for 9 volt batteries
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.
$19.00
Tool - Anvil for Turret Terminals, .750 L
Turret anvil for use with our turrets (S-HTUR-SG-2X, S-HTUR-SG-3X, S-HTUR-PR-3S).
For staking tool see S-T1715
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$14.39
Battery Holder - AA, Chassis Mount, Wired, Single
Prewired AA battery holder. This plastic battery holder fits a single AA battery and is a great option for vintage fuzz pedals that run on 1.5V, such as the Maestro FZ-1A.
$1.10
Soldering iron tip - Weller, conical, for WTCPT
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Conical Tip for TC201 Series Iron
  • PTP7 - 0.79mm / 0.031" diameter conical tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
$5.95
Soldering iron tip - Weller, screwdriver, for WTCPT, 700F
Restore the performance of your soldering iron by replacing the tip. Replacement for S-TWTCP
  • PT Series Screwdriver Tip for TC201 Series Iron
  • PTA7 - 1.6mm / 0.063" diameter screwdriver tip
  • Solid copper, plated with iron all over
  • Designed to provide maximum heat transfer from the heater to the tip
  • Tinned with lead-free solder
  • Use only genuine Weller tips
$5.95
Terminal Strip - 5 Lug, 5th Lug Common, Horizontal, package of 5
Package of 5
Standard size terminal strips, 1/16 thick bake lite tin plated steel solder lugs and brackets on 3/8" centers. 5 lug 1 ground fifth lug common.
$5.00
Battery Box - Gotoh, single, 9 volt, with removable adapter
Single 9 volt battery box. See P-ECB-9V1A for single battery box without removable adapter. See P-ECB-9V2 for double battery box.
$13.95
Soldering Iron Tip - Weller, hollow core, single flat / sloped type, ET Series
Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$5.94
Terminal Strip - Barrier Strip, 5 Pole, Dual Lugs
High quality 5 pole dual barrier strip. These terminal blocks have a solid PBT base with plated brass terminals and combination head screws. Features:
  • PBT Base
  • Closed Back Design
  • Combo Phil-Slot Nickel-plated Steel Screws
  • Plated Brass Terminals
  • 5 Poles
  • 10 Lugs
  • 57.2mm Mounting Centers
  • UL 94V-0
$2.75
Alignment Tool - Zenith-Admiral Hex Wrench
GC Electronics 8606 alignment tool with hex and special tip slug. This tool is made of non-conductive Delrin.
  • End 1 - 0.027 in.
  • End 2 - 0.1 in.
  • End 3 - 0.1 in.
$1.50
Desoldering pump tip - Weller, replacement for 7874B
Restore the performance of your desoldering pump by replacing the tip. Replacement for S-T7874B.
$8.11
Soldering Iron Tip - Weller, hollow core, long screwdriver type, ET Series
Genuine Weller long screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The long screwdriver style is great in situations where additional length is required or for narrow places. These tips are an excellent choice for use with the S-TWE1010 soldering station.
$5.94
Breadboard - Solderable PCB, 3.00” x 1.90”
The SB400 Solderable PCB BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. The SB400 has the same pattern and spacing as a standard 400 connection point BB400 solderless plug-in breadboard. It has a standard 5-hole strip for each IC pin, just like solderless breadboards plus 4 power rails. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The SB400 has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used. BPS prototyping boards use high-quality FR4 glass epoxy PCBs for long life, with an anti-tarnish protective coating for easy soldering.
$4.35
BreadBoard - Solderless, 400 point pattern
Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.
$5.50
StripBoard - Single Sided, 3.94” x 3.15”, Mounting Holes
ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$4.75
ZipWire - Jumper Cable Kit for circuits
Package of 120
The ZipWire™ Kit provides a convenient way to connect the signals in your projects. The wires can be unzipped for individual wires as needed and the color-coding can be used to organize power, ground and other signal types to keep your circuit organized. The rainbow colored ribbon cable provides the 10 standard electrical colors.
Starting at $9.85
Desoldering Pump - Weller, manual, for removing solder
Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. This lightweight desoldering pump has an anodized aluminium body to assure durability and features a plunger safety shield, short-stroke plunger and a no-clog automatic tip cleaner. Replace tip with S-T7875B. Made in Taiwan.
$34.12
Soldering Iron Tip - Weller, single flat / sloped type, ST Series
Genuine Weller single flat style tips for use with all ST Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
$5.97
ProtoBoard - Fits 1590B, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590B die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590B enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190) Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 2 mounting holes.
  • PCB Size 2.05 x 4.05 in (52.1 x 102.9 mm)
$3.59
ProtoBoard - Fits 1590BB, 1 sided, 2-hole strips
Prototyping circuit board (PCB) designed to fit the Hammond 1590BB die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590BB enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190). Features:
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • Convenient 2-hole pattern provides an easy way to connect parts.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
  • 0.042" holes are drilled on 0.1" (2.54mm) centers. 4 mounting holes.
  • PCB Size 3.20 x 4.25 in (81.3 x 108.0 mm)
$5.75