Circuit Design

Soldering iron station - Weller, WE 1010, 70W, digital display
The Weller WE1010 is an excellent soldering station for professional use and beginner hobbyists alike. With increased power and stability, the WE1010 is an upgrade in many ways for users of the WES51 and WTCPT soldering stations.
$143.00
Digital Capacitance Meter - YF-150, 9 ranges
Nine ranges give precision readings from 0.1 pF to 20,000 µF. Can be used to check virtually all capacitors for tolerance value, selecting matched sets, etc.
  • 0.1 pf to 20,000 μF, 9 ranges
  • Over range indicator
  • 0.5% basic accuracy
  • Tilt stand
  • 3-1/2 digit LCD, 1" h x 2-¼" w
  • 1.5" x 2.8" x 6"
  • Zero adjustment
  • Input protected
  • Low battery indicator
  • Includes case, leads, battery, spare fuse and instructions
$49.95
Staking Tool - For Small Eyelets
Staking tool for small eyelets such as S-HEYE-B. Directions:
  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$14.39
Digital Multimeter - YF-3220, multi-purpose
Ergonomically designed. Uses one 9V battery, included.
  • 0.5% basic DC accuracy
  • audible continuity test
  • 3 1/2 digit LCD, 0.625" high
  • 10M ohm input resistance
  • 1.5" x 3" x 7.5"(w/o rubber case)
  • overload protection
  • voltage to 1000VDC, 750VAC
  • capacitance to 20 microfarads
  • polarity indicator
  • frequency to 10MHz
  • over range indicator
  • 10A (AC or DC)
  • low battery indicator
  • hFE and diode test
  • tilt stand and case
$49.95
Breadboard - Solderable PCB, 3.75” x 1.85”, Mounting Holes
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.75
Soldering iron tip - Weller, hollow core, 1.6mm, narrow screwdriver, ET Series
Genuine Weller narrow screw driver (chisel) style tips for use with all ET Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$5.94
Soldering Iron Tip - Weller, narrow screwdriver type, ST Series
Genuine Weller narrow screw driver (chisel) style tips for use with all ST Series compatible soldering irons. The narrow screwdriver style is great for soldering in hard to reach and narrow spots. These tips are an excellent choice for use with the S-TWLC100 soldering station.
For use with Weller Irons: SP40N, WP25, WP30, and WP35; and WLC100 station
$5.95
Soldering Iron - Weller SPG80L, 80 watts
The Weller SPG80L is a heavy duty 80 Watt soldering iron. It is ideal for soldering chassis connections in classic amps such as can capacitors and can be used in many other applications. This soldering iron has an indicator light that shows when the iron is turned on for safe use. The barrel is stainless steel and the rugged tip is replaceable. The impact resistant handle remains cool when in use. Features:
  • 900°F tip temperature suitable for chassis soldering and other heavy duty applications
  • Indicator light to show when the iron is on
  • 3/8” chisel tip
  • 6 foot power cord
  • Metal stand included
$50.65
Battery Holder - AA, Chassis Mount, Wired, Double
Prewired AA battery holder. This plastic battery holder fits two AA batteries. The six inch leads are prestripped and tinned stranded wire for an easy installation.
$1.25
StripBoard - Single Sided, 3.04” x 1.55”, Vintage Spacing, Phenolic Board
Stripboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This stripboard features a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid (10 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is gold coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm phenolic circuit board
  • Gold coated strips
  • 20 x 10 holes (10 strips)
  • 3.04” x 1.55”
$2.95
Solder station - Weller, WLC100, 40 watts
40 Watts Soldering Station for Hobbyist and DIYer
  • Input Voltage: 120
  • Output Voltage: 120
  • Power Consumption: 5 - 40 watts
  • Temperature Range: 900ºF max
  • On/Off switch with "power-on" indicator light
  • Variable control produces 5 to 40 watts
  • Natural sponge tip cleaning pad
  • Ideal for hobbyist, DIYers and students
  • Includes 1/8" screwdriver tip
  • UL listed
$70.95
Solder - Kester 48, .031", Flux 66, Lead-free 1 lb Spool
Lead free solder, Sn96.5Ag3.0Cu0.5, 031" diameter, rosin flux, core 66. Kester SAC305 48 Activated Rosin Flux for cored solder wire was developed for lead-free applications to enable soldering of most common metals.
$99.75
Tagboard - 40 Turret Pins, High Quality
200mm x 45mm turret board with two rows of of 20 turrets. These turrets are seamless contact pin style turrets. Each turret features an additional solderpad for adding additional components or wiring. This board has four mounting holes.
$9.82
Tagboard - 300mm x 16mm, 26 Tags, single row
300mm x 16mm tagboard with a single row of 26 tags. Each connector features two lugs for easy wiring. This board can be used for stand alone projects or can be used to expand the P-HTAG-56. This board features four mounting holes.
$5.25
Pen - Caig, Circuit writer, for drawing traces
Circuit Writer precision conductive ink dispenser makes instant traces on most surfaces(epoxy, glass, metal). Draw traces on circuit boards, repair defective traces, make jumpers and shield electronics, design prototype circuits, repair rear-window heater traces. Silver based solution, 7ml pen dispenser.
$23.95
Bulb solder-off - Weller, for removing solder
Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. Begin by squeezing, then hold over the solder to be removed and release the bulb to allow the solder to be sucked into the bulb. This method of solder removal is very basic and inexpensive. The bulb takes up very little space in your tool kit. Made in Taiwan.
$23.75
Soldering iron - Weller, WP35, controlled output
  • Input Voltage: 120
  • Power Consumption: 35 watts
  • Tip Temperature: 850ºF
  • Heating Element Type: Nichrome wound, fiberglass and ceramic insulated
  • Lightweight handle with cushion grip for ease of use and comfort
  • Comes with 1/8" screwdriver tip
  • Stand (S-TPH60) sold separately
  • Three wire grounded power cord for your safety
  • UL listed
Stand sold separately (S-TPH60)
$68.95
On Backorder
PadBoard - Double Sided, Plated Holes, 6.30” x 3.94”, Mounting Holes
The PadBoard-3U prototyping circuit board has a general purpose pad-per-hole pattern which is good for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. The PCB accepts a 96 pin DIN-41612 VME connector for backplane or board-to-board applications. Holes for ejector latches are provided. Features
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$12.95
StripBoard - Single Sided, 3.04” x 1.55”, 0.1” Spacing, Phenolic Board
Stripboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This stripboard features standard 0.1” (2.54mm) spacing. The board has a 30x15 grid (15 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is gold coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm phenolic circuit board
  • Gold coated strips
  • 30 x 15 holes (15 strips)
  • 3.04” x 1.55”
$2.75
PadBoard - Double Sided, Plated Holes, 3.94” x 3.15”, Mounting Holes
The PadBoard-2 prototyping circuit board has a general purpose pad-per-hole pattern which is good for analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. Features
  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 31 x 39 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size2 = 100 x 80mm (3.94 x 3.15in), 1/16" thick (1.6mm)
$5.95
Soldering Iron - Battery Powered, Portable
This portable battery powered soldering iron is great in a pinch. The small sized iron is a perfect fit in a gig bag or backpack.
$11.95
Soldering iron stand - Weller, for WP35
Stand for weller soldering iron part number S-TWP35.
$49.33
Soldering Iron Tip - Weller, for PSI100, Hot Knife tip
Replacement hot knife tip (cat no. PSI 10) for Weller Portasol, butane soldering iron. Cut and cauterize nylon ropes and synthetic upholstery materials easily. Adjustable temperatures up to 450°C (850°F) make it perfect for cutting and shaping plastics and model making.
$18.73