You are here

Circuit Design

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(8 pages)
S-Z370Analog Multimeter - Volt-Ohm-Millimeter
Intermagnetic version to prevent interference from magnetic fields. Double protection of diode and fuse, transistor hFE test function. DCV: 0.25V, 0.5V, 2.5V, 10V, 50V, 250V 1000V. ACV: 10V, 50V, 250V, 500V,1000V. DCA: 50 uA, 2.5 mA, 25mA, 250mA. Ohms: x1, x10, x1k, x10k. Dimensions: 148mm x 98mm x 41mm
$16.95
Click to read more
P-ECB-244Battery Box - Dunlop
Original Dunlop snap-in, black battery box with snap-closed swing door for effects pedals using one 9 volt battery (accessed via the bottom of the pedal). Cutout dimensions: 2.46" x 1.27", box depth: 0.70", snaps over a panel thickness of about 0.04". Used on Dunlop Cry Baby Wah Wah GCB95 and many Dunlop effects pedals.
$1.75
Click to read more
P-ECB-9V2Battery Box - Gotoh, Dual, 9 Volt
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries.
Four wood screws included.
Directions:
1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24")
2. Put the box in guitar body and fix it by screws.
$19.00
Click to read more
P-ECB-9V1ABattery Box - Gotoh, single, 9 volt
Single 9 volt battery box.
See P-ECB-9V1B for single battery box with removable adapter.
See P-ECB-9V2 for double battery box.
$13.95
Click to read more
P-ECB-9V1BBattery Box - Gotoh, single, 9 volt, with removable adapter
Single 9 volt battery box.
See P-ECB-9V1A for single battery box without removable adapter.
See P-ECB-9V2 for double battery box.
$13.95
On Backorder
Click to read more
S-H155Battery Clip - 9 Volt (Package of 3)

9 volt battery clip with 5 3/4" red and black wire lengths. Simple construction and perfect for use in effects pedals. Package of three.


$0.60
Click to read more
K-P155Battery Clip - 9 Volt with Vinyl Tab

Single standard snap-on 9V battery clip. Features six inch pre-stripped and pre-tinned leads for an easy connection.


$0.60
Click to read more
P-PC-SB404BreadBoard - Solderable PCB, 400 point pattern
Solderable PC BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. This breadboard has the same pattern as a standard 400 connection point solderless plug-in breadboard which has a standard 5-hole strip for each IC pin, just like solderless breadboards. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts.
The board has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used as well as a top side silkscreen to position components. Four mounting holes allow your projects to be secured.
$4.50
Click to read more
P-PC-BB400BreadBoard - Solderless, 400 point pattern

Solderless (plug-in) breadboard with 400 connection tie-points (i.e. 400 wire insertion holes) and 4 power rails. Solderless breadboards are great for building and testing new circuits because parts can be easily inserted and removed making them completely re-usable. This breadboard has a 300 tie-point IC-circuit area plus four 25 tie-point power rails. The housing is made of white ABS plastic, with a printed legend giving numbers and letters for columns and rows. The internal contacts are phosphor bronze with a plated nickel finish and a peelable adhesive tape backing is provided for attaching it to a surface. Be sure to check out the Zipwire™ jumper wire kits for use with this breadboard.


$4.75
Click to read more
S-T7805Bulb solder-off - Weller
Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning.
Begin by squeezing, then hold over the solder to be removed and release the bulb to allow the solder to be sucked into the bulb. This method of solder removal is very basic and inexpensive. The bulb takes up very little space in your tool kit. Made in Taiwan.
$18.95
Click to read more

Pages

(8 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Circuit Design