Circuit Design

Turrets - Bifurcated, for use on 2mm boards
Package of 10
Bifurcated turrets for use on boards measuring 2mm thick. Made of nickel plated copper. These are sometimes referred to as split or forked turrets. For use with 3mm boards, see S-HTUR-BI-3S. Stake and anvil required for mounting. Staking Tool is our part number S-T1715. Anvil is our part number S-T1717. For a budget tool set see S-T-STAKE-SET.
$2.25
Turrets - Bifurcated, Screw Mount
Package of 10
Bifurcated turrets with a screw mount that works on boards with thicknesses of 1.5mm to 4mm. Made of gold plated brass. These are sometimes referred to as split or forked turrets. Includes a mounting washer, lock washer, and mounting nut. The staking tool is not required for these turrets.
$5.95
Turrets - Bifurcated, for use on 3mm boards
Package of 10
Bifurcated turrets for use on boards measuring 3mm thick. Made of nickel plated copper. These are sometimes referred to as split or forked turrets. For use with 2mm boards, see S-HTUR-BI-2S. Stake and anvil required for mounting. Staking Tool is our part number S-T1715. Anvil is our part number S-T1717. For a budget tool set see S-T-STAKE-SET.
$2.25
StripBoard - Single Sided, 3.04” x 1.55”, 0.1” Spacing, Phenolic Board
Stripboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This stripboard features standard 0.1” (2.54mm) spacing. The board has a 30x15 grid (15 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is gold coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm phenolic circuit board
  • Gold coated strips
  • 30 x 15 holes (15 strips)
  • 3.04” x 1.55”
$2.75
StripBoard - Single Sided, 3.04” x 1.55”, Vintage Spacing, Phenolic Board
Stripboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This stripboard features a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid (10 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is gold coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm phenolic circuit board
  • Gold coated strips
  • 20 x 10 holes (10 strips)
  • 3.04” x 1.55”
$2.95
Battery Holder with Connector - 9V, Chassis Mount, Horizontal
High quality chassis mount battery holder with a built-in connector. This clip fits standard 9V batteries. The horizontal mount and small footprint of the holder allows for easy placement where vertical space is limited. The two connections use individual solder tabs for hard wiring directly into projects providing a rugged and stable connection.
$5.45
Battery Clip - Premium, 9 Volt, Rigid Frame, T-Style, Shielded Eyelets
Premium 9V battery clip made of a rigid plastic frame with an insulating wall enclosing the battery terminals. This high quality battery snap features nickel-plated brass contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
$1.15
Battery Clip - Premium, 9 Volt, Rigid Frame, T-Style
Premium 9V battery clip with a rigid plastic frame. This high quality battery snap features nickel-plated phosphor bronze contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.
$1.15
Solder - Kester, 60 / 40, 44 Flux, 1 lb spool
60/40 Rosin Core, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.
Starting at $49.95
Turrets - 0.172" Long, Brass, Premium, Package of 10
Package of 10
Hollow Turret Terminal,Brass, .172" Long, Premium.
  • Finish/Plating: Tin
  • For Panel Thickness: .125 [3.2]
  • Material: Brass
  • Mounting Hole: 0.116
  • Terminal Length: 0.312
  • Terminal Style: Tubular Turret
  • Type: Solder Turret Terminal
  • Package of 10
$4.95
Desoldering Pump - Weller, manual, for removing solder
Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. This lightweight desoldering pump has an anodized aluminium body to assure durability and features a plunger safety shield, short-stroke plunger and a no-clog automatic tip cleaner. Replace tip with S-T7875B. Made in Taiwan.
$34.12
Fiberboard - Vulcanized, 3" x 15", .062" Thick
Vulcanized Fiberboard, used for laying out circuits using eyelets such as S-HEYE-A and our staking tool S-T1715.
  • .062" thick
  • 3" x 15"
$2.45
Alignment Tool - Zenith-Admiral Hex Wrench
GC Electronics 8606 alignment tool with hex and special tip slug. This tool is made of non-conductive Delrin.
  • End 1 - 0.027 in.
  • End 2 - 0.1 in.
  • End 3 - 0.1 in.
$1.50
Terminal Strip - 5 Lug, 1st Lug Common, Horizontal, package of 5
Package of 5
Standard size terminal strips, 1/16 thick bakelitetin plated steel solder lugs and brackets on 3/8" centers. 5 lug 1 ground first lug common
$4.95
Battery Clip - 9 Volt with Vinyl Tab
Single standard snap-on 9V battery clip. Features six inch pre-stripped and pre-tinned leads for an easy connection.
$0.50
Tagboard - 40 Turret Pins, High Quality
200mm x 45mm turret board with two rows of of 20 turrets. These turrets are seamless contact pin style turrets. Each turret features an additional solderpad for adding additional components or wiring. This board has four mounting holes.
$9.82
StripBoard - Single Sided, 3.94” x 3.15”, Mounting Holes
ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$4.75
Terminal Strip - 6 Lug, 2nd Lug Common, Horizontal, package of 5
Package of 5
Standard size terminal strips, 1/16 thick bakelitetin plated steel solder lugs and brackets on 3/8" centers. 6 lug, 1 ground. Second lug common.
$5.95
Soldering Iron - Weller SPG80L, 80 watts
The Weller SPG80L is a heavy duty 80 Watt soldering iron. It is ideal for soldering chassis connections in classic amps such as can capacitors and can be used in many other applications. This soldering iron has an indicator light that shows when the iron is turned on for safe use. The barrel is stainless steel and the rugged tip is replaceable. The impact resistant handle remains cool when in use. Features:
  • 900°F tip temperature suitable for chassis soldering and other heavy duty applications
  • Indicator light to show when the iron is on
  • 3/8” chisel tip
  • 6 foot power cord
  • Metal stand included
$49.95
Soldering Iron Tip - Weller, hollow core, single flat / sloped type, ET Series
Genuine Weller single flat style tips for use with all ET Series compatible soldering irons. The single flat style is versatile tip style that works great in situation where precision is required as well as situations where heat needs to be spread efficiently. These tips are an excellent choice for use with the S-TWE1010 soldering station.
  • Sensor hole in the base of tip is fitted with a stainless steel liner
  • Prevents the tip from seizing to the sensor
$5.94
Pen - Caig, Circuit writer, for drawing traces
Circuit Writer precision conductive ink dispenser makes instant traces on most surfaces(epoxy, glass, metal). Draw traces on circuit boards, repair defective traces, make jumpers and shield electronics, design prototype circuits, repair rear-window heater traces. Silver based solution, 7ml pen dispenser.
$23.95
StripBoard - Single Sided, 6.30” x 3.94”
ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features
  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
$8.75
Battery Box - Gotoh, single, 9 volt, with removable adapter
Single 9 volt battery box. See P-ECB-9V1A for single battery box without removable adapter. See P-ECB-9V2 for double battery box.
$14.95
Terminal Strip - 2 Lug, 2nd Lug Common, Horizontal
Package of 5
Standard size terminal strip, 1/16" thick bakelite, tin plated steel lugs and brackets on 3/8" centers.
$3.65