You are here

Circuit Design

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(4 pages)
S-CRSF-R80-XSoldering Flux - Caig, non-spill Rosin Flux

Low residue, no-spill. Thermal stability enabling excellent wetting and reduced carbonization at soldering temperature. No-clean flux can be removed by wiping with a cloth or with cleaning solvent. Nonflammable and non corrosive. Recommended for electrical and electronic soldering applications.


$7.15
Starting at $6.43
You save: 10%
Click to read more
S-T156Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
$1.75
$1.58
You save: 10%
Click to read more
S-T1714Staking Tool - For Small Eyelets

Staking tool for small eyelets such as S-HEYE-B. Directions:



  • Drill hole using #42 drill bit
  • Insert eyelet
  • Flip board over onto a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board

$13.95
$12.56
You save: 10%
Click to read more
S-T22-XSolder wick - GC Braid, multiple sizes

5 feet Long. Great for removing solder from printed circuit boards or other electronic equipment.


$3.50
Starting at $3.15
You save: 10%
Click to read more
S-T305Soldering Iron - Battery Powered, Portable

This portable battery powered soldering iron is great in a pinch. The small sized iron is a perfect fit in a gig bag or backpack.


$11.95
$10.76
You save: 10%
Click to read more
S-T702Alignment Tool - Zenith-Admiral Hex Wrench

GC Electronics 8606 alignment tool with hex and special tip slug. This tool is made of non-conductive Delrin.



  • End 1 - 0.027 in.
  • End 2 - 0.1 in.
  • End 3 - 0.1 in.

$1.20
$1.08
You save: 10%
Click to read more
S-T7805Bulb solder-off - Weller, for removing solder

Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. Begin by squeezing, then hold over the solder to be removed and release the bulb to allow the solder to be sucked into the bulb. This method of solder removal is very basic and inexpensive. The bulb takes up very little space in your tool kit. Made in Taiwan.


$19.49
$17.54
You save: 10%
Click to read more
S-T7874BDesoldering Pump - Weller, manual, for removing solder

Removes melted solder by suction. Facilitates accurate printed circuit repair and cleaning. This lightweight desoldering pump has an anodized aluminium body to assure durability and features a plunger safety shield, short-stroke plunger and a no-clog automatic tip cleaner. Replace tip with S-T7875B. Made in Taiwan.


$29.50
$26.55
You save: 10%
Click to read more
S-T7875BDesoldering pump tip - Weller, replacement for 7874B
Restore the performance of your desoldering pump by replacing the tip. Replacement for S-T7874B.
$6.98
$6.28
You save: 10%
Click to read more
S-T9000-LFXSolder - Kester 48, .031", Flux 66, Lead-free 1 lb Spool

Lead free solder, Sn96.5Ag3.0Cu0.5, 031" diameter, rosin flux, core 66. Kester SAC305 48 Activated Rosin Flux for cored solder wire was developed for lead-free applications to enable soldering of most common metals.


$80.00
Starting at $72.00
You save: 10%
Click to read more

Pages

(4 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Circuit Design