Clearance Items

The JJ Electronic EF806S is a high quality reproduction of the classic EF86. This pentode features a robust construction with the internal shielding used in the original tubes. The JJ EF806 can be used in any EF86 circuit including microphones and amplifiers.

• Vertical Mount. For Horizontal Mount, see P-T263-Z
• Primary 115 VAC, 60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).

This zinc diecast height adjustable stop tailpiece from GOTOH features threaded adjustable studs and knurled bushings. Hardware included. Anchor bushings: M8x1.25, 25mm height.

Amphenol AX series XLR cable connector, 3 pole male, Machined contacts The revolutionary AX series of XLR connectors introduce an exciting contemporary look and feel to the professional audio interconnect market. They are designed to complement modern audio architecture and truly “fit" within their environment.

Bridge A modern version of the Tune-o-matic style bridge for the solidbody guitar. Pre-notched saddles with an individual saddle intonation screw retained by mini hex nuts for each one. Standard mounting post style and features hard zinc saddles. Hardware included.

• Replacements for Marshall Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

1/4" Mono phone plug, diecast shell, satin finish, flexible grommet. Features:

• Stylised Shell design
• Robust diecast shell
• Great solderability with increased solder area
• Precision machined contacts
• Flexible grommet cable protection
• Quick and easy assembly
• Large cable O.D. Entry to 8mm (0.315”)

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
• Highpot tested: 2,000 VAC
• Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
• Windings: Concentric wound for low stray field and low noise.
• Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
• Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
• Conservative designs - CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Designed for small power or bias supplies, test equipment, preamps etc.
• Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
• Economical , two hole, channel bracket, chassis mount.
• Minimum 5" long leads.
• Convenient 6.3 filament/auxiliary winding.

Amphenol AX series XLR cable connector, 3 pole male, Machined gold-plated contacts, Black Finish The revolutionary AX series of XLR connectors introduce an exciting contemporary look and feel to the professional audio interconnect market. They are designed to complement modern audio architecture and truly “fit" within their environment.

Beam power pentode primarily intended for use as an audio frequency power amplifier. It is particularly useful in applications where the available supply voltage is relatively low.

The N12K was developed in conjunction with Fender® as the speaker for the new Fender® Tone Master™ Deluxe Reverb® and Twin Reverb®. It delivers the closest sound, character and dynamic feel of the classic Jensen C12K with half the weight, thanks to the exclusive Jensen Neodymium magnet design (the same magnet used in the Tornado series). The N12K delivers a warm, full bodied tone with remarkable headroom and just the right amount of brilliance and sparkle.

XLR 3 pole male, stamped contacts, nickel finish, jaws cable clamp. Features:

• Zinc Diecast Shell
• Solder Bucket connections
• "Jaws" Cable Retention System
• Leading first mate last break socket contact
• Quick and easy assembly without screws
• Precision machined contacts

Miniature heptode primarily intended to perform the combined functions of mixer and oscillator in automobile radio receivers. Specially designed to operate with plate and screen voltages supplied directly from a 12-volt storage battery.

XLR 3 pole female, stamped contacts, jaws cable clamp.
Features:

• Zinc Diecast Shell
• Solder Bucket connections
• "Jaws" Cable Retention System
• Precision machined contacts
• Leading first mate last break socket contact
• Quick and easy assembly without screws

Plastic panel-mount male XLR jack from Amphenol with a vertical PCB mount. The AC series, A and B type XLR chassis receptacles have been designed and manufactured with the Original Equipment Manufacturers’ (OEM) needs in mind. The compact shell design allows a significant space saving over the traditional ‘D’ type shell. Gold plated contacts improve the performance, ensuring a reliable contact and the unique grounding link options offer flexibility in design. Features

• Vertical PCB mount
• Compatible with all other XLR brands
• Gold Contacts
• Precision Machined Pin contacts

The type 3Q4 is a miniature type power-amplifier pentode designed for use in the output stage of battery operated equipment.

XLR 3 pole female, stamped contacts, large jaws cable clamp.

2-pole 1/4" professional right-angle phone plug, gold contacts, black shell. Large jaw cable clamp for use with cable with an outer diameter of 5.5mm to 6.5mm.

The HB-Classic α is a vintage-style humbucker pickup. This pickup uses a made in USA Alnico 2 bar magnet for a smooth vintage tone. This pickup is wax-potted for sonic stability and uses a shielded 4-conductor wire for various wiring options. The HB-Classicα humbucker comes in various open and covered options to match the look of any guitar. Mounting screws and springs are included. Made in Japan.

Genuine Korg momentary switch used in many Korg products.such as the O5R/W, A1, i30, i30HD, OASYS, Trinity, Triton, Triton EX, Triton Studio, and X5DR.

Heater-cathode type beam tube of miniature construction designed primarily to form the combined operations of the limiter, discriminator, and audio-voltage amplifier in FM and intercarrier television receivers.

1/4" phone plug, jaws cable clamp, thermoplastic backshell. Features:

• Stylised Shell design with ergonomic grip
• Robust diecast keyed shell
• Great solderability with increased solder area
• Precision machined contacts
• "Jaws" cable retention system
• Quick and easy assembly
• Nickel-plated contacts

• Enclosed, 4-hole mount chokes
• Tolerance of 15% on both inductance & resistance.
• Inductances measured at rated D.C. current.
• Minimum 8" long leads.
• Units will exhibit less inductance at slightly higher currents or more at lower currents.
• Perfect for high voltage power supply filtering, case matches power transformers & tube audio output transformers.
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
• For more sizes and voltages (open - bracket mount type) - see P-T154-P-T156-X
• Operating temperature range is -40C to 85C