Clearance Items

Fits most American and Mexican stratocasters. 3 ply standard 11 hole pickguard. Fits 3 single coil pickukps.

Fits most American Telecasters. This modern pickguard fits American, American Standard, American Deluxe, American Special, Highway One™, Road Worn®, Deluxe Player, Blacktop, Standard and Deluxe series Telecaster guitars (also fits Squier® Standard series Telecaster models 2004-present).

Original Fender® pickguard. This vintage-style pickguard fits many 1950s-style American Vintage, Hot Rod, Road Worn®, Classic Player and Classic series Stratocaster guitars with three single-coil pickups.

Original Fender® pickguard replacement for 62' P-Bass, 4-ply.

Original Fender® pickguard replacement, 3-ply, for American Precision Bass. This pickguard fits American, American Standard, American Vintage, Standard and Deluxe series Precision Bass models (does not fit five-string Precision models).

Slightly hotter than the 54 models, these recreations of the 1957 Strat® single coil pickups deliver a true vintage tone not available until now. Middle position reverse wound/reverse polarity to achieve noise cancellation when utilizing a 5 way switch. 42 gauge Formvar wire and Alnico III magnets. White covers.

• Magnet Type = Alnico 3 pole pieces
• D.C. Resistance = 5.92k Ohms
• Inductance (henrys) = 3.61
• Wire Type = Formvar AWG 42
• Lead Type = cloth insulated 2 conductor
• Polarity = normal

This McNelly Stagger Swagger pickup features a nickel plated cover, a braided-shield/single-conductor wire, and a 1 15/16" string spacing.

A1837 Transistor - Fender. Power amplifier applications and Driver Stage Amplifier Applications.

High performance, ultrafast diodes. Improve efficiency, reduce noise, allow higher frequency operation.

A surface-mount version of P-QLM1458, this LM1458M dual op amp comes in an 8-pin surface-mount package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features

• No Frequency Compensation Required
• Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• Low-Power Consumption
• 8-Lead TO-99 and 8-Lead PDIP
• No Latch Up When Input Common Mode Range is Exceeded

The BTSE-99FX Effect board provides 99 different digital audio effects to be used in many audio applications that require sound enhancement. Equipped with a superb quality digital effects processing engine which adds that extra punch needed to make sounds truly stand out. Applications:

• Guitar/ Keyboard/Bass amplifiers and combos
• Audio mixing consoles / Powered mixing consoles
• Stand -alone stereo effect units for studio and PA usage
• Effects pedals

9-pin Micalex ceramic tube socket for auto-wave soldering applications.
Measurements:

• Center PCB hole diameter -0.73"
• Mounting pin diameters - (9 holes at 1.00") and (3 holes at 1.26")

• Over designed for single ended tube output circuits (triode, tetrode or pentode tubes).
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response at least 20 Hz. to 20 Khz. at full rated power (± 1 db max. ref.

• Open style, chassis mount transformers with a 115V 60Hz or 50/60Hz primary and an 18V center tapped secondary.

• Primary 115 VAC, 60 Hz.
• Secondary 30 C.T.
• Center tapped secondary.
• Open style, channel bracket, two hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees, C).
• Hi-Pot test of 2,000 V RMS.
• UL listed (# E50394) & CSA certified (# LR3902).

• Primary 115 VAC, 60 Hz.
• Secondary 60 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Secondary 12 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Secondary 5 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Dual primary 115/230 VAC
• 50/60 Hz. operation
• Dual secondaries for series or parallel connections
• 4,000 V RMS Hipot test
• Class F insulation (155 degrees, C)
• Chassis mount
• Dual bobbin construction
• Dual use terminals
• C UL US recognized (E207860)
• TUV Type Approved
• CE certified to IEC 950 (Approved to EN 60-742 Safety Isolating Transformers)

• Vertical Mount. For Horizontal Mount, see P-T263-Z
• Primary 115 VAC, 60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120 for 120 V transformers, P-T290-Fender-120-UP for upgraded 120 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
• Highpot tested: 2,000 VAC
• Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
• Windings: Concentric wound for low stray field and low noise.
• Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
• Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
• Conservative designs - CSA certified (209651).

Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware. Sealed case and wax potted core internally for stable characteristics and long life. Wide frequency response +/- 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, may be down 1 db @ 20 Khz.) Insertion loss of apx. 1 db.

Replacement for Bassman heads. Equivalent to #125A13A & #022871.