Clearance Items

Black Cliff K5 knob with short indicator line. ¼" shaft with set screw. Replacement for Marshall. Measures 0.75" in height. See P-K342-NOI for a version with no indicator line.

Low cost, high quality 3.5mm patch cables in a variety of lengths and colors. The cables are super flexible, have a great droop, and are shipped coiled so no permanent kinks are formed. With the large selection of lengths and colors, these cables are the perfect choice for any sized system.

Fits most American and Mexican stratocasters. 3 ply standard 11 hole pickguard. Fits 3 single coil pickukps.

Fits most American Telecasters. This modern pickguard fits American, American Standard, American Deluxe, American Special, Highway One™, Road Worn®, Deluxe Player, Blacktop, Standard and Deluxe series Telecaster guitars (also fits Squier® Standard series Telecaster models 2004-present).

Original Fender® pickguard. This vintage-style pickguard fits many 1950s-style American Vintage, Hot Rod, Road Worn®, Classic Player and Classic series Stratocaster guitars with three single-coil pickups.

Original Fender® pickguard replacement for 62' P-Bass, 4-ply.

Original Fender® pickguard replacement, 3-ply, for American Precision Bass. This pickguard fits American, American Standard, American Vintage, Standard and Deluxe series Precision Bass models (does not fit five-string Precision models).

Slightly hotter than the 54 models, these recreations of the 1957 Strat® single coil pickups deliver a true vintage tone not available until now. Middle position reverse wound/reverse polarity to achieve noise cancellation when utilizing a 5 way switch. 42 gauge Formvar wire and Alnico III magnets. White covers.

• Magnet Type = Alnico 3 pole pieces
• D.C. Resistance = 5.92k Ohms
• Inductance (henrys) = 3.61
• Wire Type = Formvar AWG 42
• Lead Type = cloth insulated 2 conductor
• Polarity = normal

This McNelly Stagger Swagger pickup features a nickel plated cover, a braided-shield/single-conductor wire, and a 1 15/16" string spacing.

A1837 Transistor - Fender. Power amplifier applications and Driver Stage Amplifier Applications.

High performance, ultrafast diodes. Improve efficiency, reduce noise, allow higher frequency operation.

A surface-mount version of P-QLM1458, this LM1458M dual op amp comes in an 8-pin surface-mount package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features

• No Frequency Compensation Required
• Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• Low-Power Consumption
• 8-Lead TO-99 and 8-Lead PDIP
• No Latch Up When Input Common Mode Range is Exceeded

The BTSE-99FX Effect board provides 99 different digital audio effects to be used in many audio applications that require sound enhancement. Equipped with a superb quality digital effects processing engine which adds that extra punch needed to make sounds truly stand out. Applications:

• Guitar/ Keyboard/Bass amplifiers and combos
• Audio mixing consoles / Powered mixing consoles
• Stand -alone stereo effect units for studio and PA usage
• Effects pedals

9-pin Micalex ceramic tube socket for auto-wave soldering applications.
Measurements:

• Center PCB hole diameter -0.73"
• Mounting pin diameters - (9 holes at 1.00") and (3 holes at 1.26")

• Over designed for single ended tube output circuits (triode, tetrode or pentode tubes).
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response at least 20 Hz. to 20 Khz. at full rated power (± 1 db max. ref.

• Open style, chassis mount transformers with a 115V 60Hz primary and a 10V center tapped secondary

• Open style, chassis mount transformers with a 115V 60Hz or 50/60Hz primary and an 18V center tapped secondary.

• Primary 115 VAC, 60 Hz.
• Secondary 30 C.T.
• Center tapped secondary.
• Open style, channel bracket, two hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees, C).
• Hi-Pot test of 2,000 V RMS.
• UL listed (# E50394) & CSA certified (# LR3902).

• Primary 115 VAC, 60 Hz.
• Secondary 60 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Secondary 12 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Primary 115 VAC, 60 Hz.
• Secondary 5 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

• Dual primary 115/230 VAC
• 50/60 Hz. operation
• Dual secondaries for series or parallel connections
• 4,000 V RMS Hipot test
• Class F insulation (155 degrees, C)
• Chassis mount
• Dual bobbin construction
• Dual use terminals
• C UL US recognized (E207860)
• TUV Type Approved
• CE certified to IEC 950 (Approved to EN 60-742 Safety Isolating Transformers)

• Vertical Mount. For Horizontal Mount, see P-T263-Z
• Primary 115 VAC, 60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120 for 120 V transformers, P-T290-Fender-120-UP for upgraded 120 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.