Clearance Items

Triode using the miniature construction. Its low capacitance and high ratio of plate current to transconductance allow use as a high frequency oscillator and mixer at frequencies below ~300 mc or as grounded grid radio frequency amplifier.

Phillips panhead machine screw, M3 metric, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head. See S-HS-M3-6-X for colored 6mm M3 screws.

Beam power pentode primarily intended for use as an audio frequency power amplifier. It is particularly useful in applications where the available supply voltage is relatively low.

Designed for use on arch top electric guitars. The Bigsby was the first successful design of what is now called a whammy bar or tremolo arm, although vibrato is the technically correct term for the musical effect it produces. In standard usage, tremolo is a rapid fluctuation of the volume of a note, while vibrato is a fluctuation in pitch. The origin of this nonstandard usage of the term by electric guitarists is attributed to Leo Fender, who also used the term “vibrato” to refer to what is really a tremolo effect.

• Model Name: B-7
• Series: Original Kalamazoo Line
• Manufacturing Method: Cast
• Manufacturing Material: Aluminum
• Approximate weight: 354 grams/12.5 oz.
• Overall Length: 8 3/4”/222.3 mm
• Overall Width: 3 5/8”/92.1 mm
• Arm adjusts with 1/8” Allen wrench and 5/16” socket wrench

2-pole 1/4" professional right-angle phone plug, gold contacts, black shell. Large jaw cable clamp for use with cable with an outer diameter of 5.5mm to 6.5mm.

9-pin Micalex ceramic tube socket for auto-wave soldering applications.
Measurements:

• Center PCB hole diameter -0.73"
• Mounting pin diameters - (9 holes at 1.00") and (3 holes at 1.26")

Genuine Bigsby® replacement handle stud.

A surface-mount version of P-QLM1458, this LM1458M dual op amp comes in an 8-pin surface-mount package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features

• No Frequency Compensation Required
• Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• Low-Power Consumption
• 8-Lead TO-99 and 8-Lead PDIP
• No Latch Up When Input Common Mode Range is Exceeded

Sharp cut-off general purpose amplifier. With the exception of heater and capacitance ratings, the electrical characteristics are similar to those of the 6C6.

Like its 12” version, the Tornado 10 is remarkably versatile, with evenly balanced tone, excellent articulation, and a detailed, dynamic response with a hint of a very musical, sweet dynamic compression. The powerful Neodymium magnet and the 2” voice coil allow for 100W of power handling in a featherlight weight of just 1.7kgs (3.75lbs)

High-mu power output triode designed for service in dynamic coupled circuits using a type 76, 6P5GT/G or 6J5GT/G as a driver. Two 6AC5GTs may be used as a zero bias class B amplifier.

300V wire nuts for use with 18 gauge through 22 gauge wires. These wire nuts are great for use on appliances, televisions, stereos, antennas, or for any small wiring application. Rated for up to 105°C.

XLR 3 Pole female audio cable connector. Musician range. Black finish, silver contact plating. "Jaws" cable retention system.

With a 90-watt power rating, the Celestion Cream is purpose-built for vintage tones, whatever kind of amp you use. By applying new technologies and manufacturing methods developed during the creation of our Creamback speakers, we've been able to deliver a higher power rating while preserving the very essence of an alnico guitar speaker.
Delivering a glorious, laid-back attack, the Cream exudes warm lows and a brilliant bell-like chime. It has smooth and organic mids, further characterised by a fine-grained detail that adds a high-definition quality to the vocal range.
The Cream has been specially created to bring alnico class to all kinds of amps from 1-watt to 90-watts. It conveys a satisfying warmth, detailed expressiveness and exceptional musicality, even at low power levels.

New Old-Stock (N.O.S.) tube. The 930 is a gas phototube sensitive to red through infrared light.

• Vertical Mount. For Horizontal Mount, see P-T263-Z
• Primary 115 VAC, 60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).

Slightly hotter than the 54 models, these recreations of the 1957 Strat® single coil pickups deliver a true vintage tone not available until now. Middle position reverse wound/reverse polarity to achieve noise cancellation when utilizing a 5 way switch. 42 gauge Formvar wire and Alnico III magnets. White covers.

• Magnet Type = Alnico 3 pole pieces
• D.C. Resistance = 5.92k Ohms
• Inductance (henrys) = 3.61
• Wire Type = Formvar AWG 42
• Lead Type = cloth insulated 2 conductor
• Polarity = normal

Angled nozzle attachments for the Atten ST-862D hot air station. These attachments are a great accessory allowing for a more relaxed grip and better control. Sold individually.

Transmitting beam power amplifier.

Designed for use on arched top electric guitars Bigsby B16 Specifications

• Model Name: B-12
• Series: Original Kalamazoo Line
• Manufacturing Method: Sand Cast
• Manufacturing Material: Aluminum
• Approximate weight: 344 grams/12.1 oz.
• Overall Length: 8 3/8" / 212.7 mm
• Overall Width: 3 5/8" / 92.1 mm
• Arm adjusts with 1/8" Allen wrench and 5/16" socket wrench

Consists of two diodes and a pentode utilizing a common cathode. It is designed for service as a combined detector, AVC rectifier, and pentode amplifier.

A modern version of the Tune-o-matic style bridge for guitars. Pre-notched titanium saddles with an individual saddle intonation screw retained by mini hex nuts for each saddle. Threaded thumbwheel style studs and anchor bushings. Hardware included.

1/4" phone plug, jaws cable clamp, thermoplastic backshell. Features:

• Stylised Shell design with ergonomic grip
• Robust diecast keyed shell
• Great solderability with increased solder area
• Precision machined contacts
• "Jaws" cable retention system
• Quick and easy assembly
• Nickel-plated contacts

Orange™ cabinet/combo covers. An essential purchase for when flight casing your cab or combo isn’t possible. Protect your Orange rig with a tough and durable vinyl fabric cabinet cover displaying the Orange logo.

• Standard 1x12 fits RK30TC / CR60C / CVR-112 Combo
• Standard 2x12 fits AD30TC / RK50C / CR120