Circuit Writer precision conductive ink dispenser makes instant traces on most surfaces (epoxy, glass, metal). Draw traces on circuit boards, repair defective traces, make jumpers and shield electronics, design prototype circuits, repair rear-window heater traces. Silver based solution, 7ml pen dispenser.

Right Angle Daisy Chain connector with standard polarity tip negative/barrel positive plugs connects the Power-All® ECO-Dapter® 9 VDC power supply to five effect pedals. The Cable-5/R can also be used with Power-All jumper cables to power effects that use different style jacks (reverse polarity, phone plug, battery clip, etc.). You can also link multiple Cable-5/R connectors to power over twenty 9-volt effect pedals or similar devices (actual number of units depends on current draw of individual units used).

Original Cliff sealed and switched blue jack. Fully threaded. Many types of professional music equipment nowadays use high power components, and need to be cooled by fans. Fans draw in dust and pollutants which can adversely affect the contacts of conventional jacks, with exposed contacts. This sealed jack avoids possibility of contamination of contacts by means of a sealing cover over the top and bottom of the jack.

Adjusting volume control and gain controls provides a wide variety of tones in spite of its simple construction. The Turbo switch provides an additional boost in volume and less internally generated distortion. It is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life.

The LoBat™ low battery indicator circuit is designed for use in electric guitars and basses with active pickups and electronics that use 9 volt batteries. Lights when battery voltage is below 7.7V. This early warning notifies the player it's time for a new battery days before tone begins to suffer!

Low profile mono jacks made by Lumberg. These high quality jacks are the perfect size for tightly packed pedal enclosures. The premium look, feel, and construction make Lumberg jacks an excellent choice for any build.

• M9*0.75 Bushing Thread
• Mono 2-Conductor
• Open Circuit (does not have switched terminal).
• Includes nut and washer.

Low profile Lumberg panel mount barrel jack with solder lugs. This high quality jack is the perfect size for smaller builds where additional space is necessary. The Lumberg low profile DC jack is also great for builds where aesthetics are a priority. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
Note: As of 2023, Lumberg has updated the design of these jacks.

Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.

Retainer (Belton). for use with EL84 tubes, mounts to chassis. Steel plate with nickel plating and natural coil spring. Note: these retainers are for specialized socket below chassis mounting. (See mounting drawing below.) The springs are too short for standard sockets mounted level with the chassis surface.

1/4" enclosed jack, switched, with chrome ferrule and straight PCB pins, mounting nut included. Wide body and extremely durable contacts.

Low profile stereo jacks made by Lumberg. These high quality jacks are the perfect size for tightly packed pedal enclosures. The premium look, feel, and construction make Lumberg jacks an excellent choice for any build.

• M9*0.75 Bushing Thread
• Stereo 3-Conductor
• Double Open Circuit (does not have switched terminal).
• Includes nut and washer.

High quality single row machine pin sockets made by Preci-Dip. These sockets are the break-away type and can easily snap into smaller sizes such as 5 separate transistor sockets.

This PCB is a recreation of the iss. 1 circuit board found in classic Fuzz Face pedals. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces are gold plated providing protection from corrosion indefinitely. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures. There are numerous great parts choices available for this PCB.

Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 5 in. x 8 in. and fit stompbox sizes up to 1590BB. Cloth pedal bags are also great packaging for boutique pedal builders.

Receptacle for panel or chassis mounting. Flange has two .136" (3.45 mm) diameter countersunk holes for #5-40 flat head mounting screws (not supplied). Mounts from front of panel or chassis in .953" (24.21 mm) diameter. Standard latchlock;

Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 4 in. x 6 in. and fit 1590B or smaller stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.

Iss. 2 fuzz PCB made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This PCB is a recreation of the iss. 2 circuit board found in classic Fuzz Face pedals. The iss. 2 version uses NPN silicon transistors. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures. For the germanium iss. 1 version of this board, see P-PC-FUZZ-ISS1-BRN.

Iss. 1 fuzz PCB made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This PCB is a recreation of the iss. 1 circuit board found in classic Fuzz Face pedals. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces are gold plated providing protection from corrosion indefinitely. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures.

1/4" Mono phone plug. Features a stylised shell design, robust diecast shell, great solderability, flexible grommet cable protection and quick and easy assembly

This board is a recreation of the MKI circuit board found in early Tone Bender pedals. When drawing the layout, an original board was closely referenced to ensure a proper match and fit. Since the MKI boards were hand drilled, the holes have an organic layout that was somewhat unique to each build. This board follows the exact hole pattern of one of these original builds. The build style is also fairly unique in the MK1. It is a point to point style board without eyelets or turrets. The leads of the parts are wrapped upward around the edge of the board and then solder is applied to connect the components. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below. There are numerous great parts choices available for this PCB.

Supa Fuzz style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the SupaFuzz pedal. The board is styled after the first version that Marshall produced which featured a printed circuit rather than a stripboard construction. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

V828 Italian fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the V828 Vox Tone Bender pedals. The board is styled after the Italian made version which was also sold as the Jen Fuzz. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board uses unique PCB mounted tags for the offboard wiring. A combination of S-HEYE-A eyelets and S-H137 solder tags (each sold separately) can be used to approximate the originals. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

1/4" Mono Phone plug, Right angle, Diecast Shell, Satin finish, Flexible grommet. Features:

• Stylised Shell design
• Robust diecast shell
• Great solderability with increased solder area
• Precision machined contacts
• Flexible grommet cable protection
• Quick and easy assembly

MKIII & MKIV fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in Vox Tone Bender MKIII pedals. The board is styled after the non-reverse version that can also be found in the Park Fuzz Sound, Rotosound Fuzz, and the MKIV Tone Bender. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board uses a unique PCB mount potentiometer R-VOMUP-100KL. A matching enclosure P-HROTO-1 can be used with the board to complete a vintage style fuzz build. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.