You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
P-R-ABEDSP Module - ABE, Accu-Bell Effector, 3 Adjustable Effects

The Accu-Bell Effector offers reverb, chorus, and delay with adjustable setting and tap tempo. This module runs on 5.5V to 9.5V DC so it is easy to incorporate into effect pedal builds. Please see the attached datasheet for an example schematic.


$21.95
Click to read more
P-PC-3PDT-BOARDPCB - Daughterboard for Wiring 3PDT Footswitches

Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.


$0.75
Click to read more
P-H-LEHLE-SW-XRelay Module - Lehle, Relay True Bypass Switching Unit

The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.


Starting at $21.89
Click to read more
P-H-LEHLE-BTN-XFootswitch - Lehle, SPST, Momentary, Soft Click, Long Life

The LEHLE SWITCH BTN is a momentary foot switch. It is housed in an M12 threaded enclosure made of stainless steel. Thanks to the gold plated contact material its life span is at least one million switching cycles electrically and mechanically. Hardware included.


Starting at $13.95
Click to read more
P-H1590BXChassis Box - Hammond, Diecast Aluminum, 4.40" x 2.38" x 1.06"
Colors Available:
New!:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Starting at $7.07
Click to read more
P-ECB-303Talk Box Tube - Dunlop, MXR Replacement

Vinyl replacement tube for the MXR® Talk Box. Tube length is 6.5 feet.


$16.95
Click to read more
P-ECB-147Battery Door with Clip - Dunlop, for Effect Pedals

Genuine Dunlop replacement battery door for effects pedals. This door fits a 9V battery.


$5.95
Click to read more
P-LRING-XLED - Footswitch Ring, With Bezel, 9V
Colors Available:

Leaded LED rings for use with standard footswitches. These LED rings use an array of LEDs with internal current limiting so no additional parts are required for use with 9VDC. Red, green, blue, and two-color combinations are available. A 15mm panel hole is required. See full dimensions below to check footswitch compatibility.


Starting at $1.50
Click to read more
K-999Effects Pedal Kit - MOD® Kits, The Saturator

The Saturator is an overdrive pedal kit that can cover a wide range of gain effects, transitioning smoothly from a massive clean boost to a warm and saturated distortion with the turn of a knob. The saturation is controlled with the "Soak" knob, which dials in the amount of symmetrical soft-clipping applied to the guitar signal. When fully counterclockwise , the signal is unaffected and clean. Rotating the knob clockwise will incrementally increase the soft-clipping, morphing from a clean signal through subtle-to-heavy saturated overdrive sounds and straight into distortion territory. The "Level" knob sets the overall volume of the clean or saturated output. Unity gain is at roughly 8 o'clock. With the "Soak" set to clean, rotating the "Level" knob clockwise will increase the level to upwards of 30dB.


$47.95
Click to read more
M-FLYECHOEffects Pedal - TWA, Flyboys FB-03, Echo

The TWA Flyboys FB-03 is a massive sounding delay pedal in a tiny package. This pedal takes you from the snappiest slapback sounds to big spacious delays with over 600 milliseconds of delay time. The bright and articulate delay signal keeps the mix crisp and transparent while the repeats add a touch of modulation for a warm tape like sound as the signal decays. The FB-03 Echo can go from one repeat to infinite repeats putting the pedal into self oscillation for wild feedback effects. The FB-03 Echo also features a true bypass footswitch and comes with a DC jack to battery clip converter cable.



  • 9VDC 2.5mm Barrel Connector
  • 42mA maximum current draw
  • True bypass switching
  • 20 – 620 ms delay time
  • Self oscillating
  • Extruded aluminum chassis
  • Quality components
  • 1.75” x 3.75” footprint

$79.00
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts