You are here

Effect Pedals & Parts

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(9 pages)
P-HWAHEnclosure - Wah Pedal Shell and Hardware
Wah pedal enclosure, bottom, and foot-pedal shell and hardware
$40.00
$36.00
You save: 10%
Click to read more about this product.
M-PAS-DKit - Power All System deluxe, for effects pedals
The Power-All Deluxe Kit provides 9 volts DC at 2000 milliamps @ more than enough current to power dozens of effect pedals, including up to 4 Line 6 Modelers! The Power-All Deluxe Kit can power eleven pedals out of the box, and comes complete with a variety of jumper cables that allow connection of phone plug, reverse polarity, digital, and battery-only pedal types.
$39.95
$35.96
You save: 10%
Click to read more about this product.
P-H1590FChassis Box - Hammond, Unpainted Aluminum, 7.38" x 7.38" x 2.48"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$30.04
$27.04
You save: 10%
Click to read more about this product.
P-RKBTSE-16FXMulti Processor Module - Belton, BTSE-16FX

The BTSE-16FX Effect board provides 16 different digital audio effects to be used for mixers or other audio applications that require sound enhancement. Equipped with the superb quality digital effects processing engine which it adds that extra punch needed to make audio presentations truly stand out.


$29.95
$26.96
You save: 10%
Click to read more about this product.
P-ECB-9V2Battery Box - Gotoh, Dual, 9 Volt
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries.
Four wood screws included.
Directions:
1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24")
2. Put the box in guitar body and fix it by screws.
$24.00
$21.60
You save: 10%
Click to read more about this product.
M-PAS-BKit - Power All System Basic, For Effects Pedals

The Power-All PA-9 Digital Power Supply is the world’s first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don’t waste money on batteries or take up valuable space with multiple “wall wart” adaptors or power bricks – the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All provides 9 volts DC at 2000 milliamps – more than enough current to power dozens of effect pedals, including up to four Line 6 Modelers! The Power-All’s special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9 now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.


$24.00
$21.60
You save: 10%
Click to read more about this product.
P-H1590EChassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 3.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$23.87
$21.48
You save: 10%
Click to read more about this product.
P-ECB-25PC Board - Dunlop, for Crybaby

Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.


$21.95
$19.76
You save: 10%
Click to read more about this product.
P-H1590VChassis Box - Hammond, Unpainted Aluminum, 4.70" x 4.70" x 3.54"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$21.59
$19.43
You save: 10%
Special Order Item
Please Contact us or call us at 480.820.5411 to order this item.
Click to read more about this product.
P-H1590DChassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 2.05"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$21.28
$19.15
You save: 10%
Click to read more about this product.

Pages

(9 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts