You are here

Effect Pedals & Parts

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(12 pages)
P-HWAHEnclosure - Wah Pedal Shell and Hardware
Wah pedal enclosure, bottom, and foot-pedal shell and hardware
$40.00
Click to read more about this product.
M-PAS-CABLE-6Cable - For Power All Systems, C-GY
Included in the PA-9 Power-All System and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack.
The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.
Cable-Grey is 158.75 mm (approximately 5.25 inches) in length from plug to plug.
NOTE: The Power-All Cable-Grey was designed to hook directly to the battery snap inside a pedal and then provide power to the pedal using an external DC power adaptor.
The wiring of the Cable-Grey’s battery snap is the OPPOSITE of what would normally be needed to connect to a 9-Volt battery.
$3.00
Click to read more about this product.
K-955Effects Pedal Kit - MOD® Kits, Thunderdrive Deluxe, Overdrive
The Thunderdrive Deluxe is an overdrive pedal kit that will provide a strong clean signal boost in the early gain settings and smooth distortion at maximum gain settings. Adjusting volume control and gain controls provides a wide variety of tones in spite of it's simple contruction.
The Turbo switch provides an additional boost in volume and less internally generated distortion. The pre-painted black enclosure, red control knobs and red LED indicator give the Thunderdrive Deluxe an understated attractive finish. It is capable of overdriving the preamp section of your guitar amp or adding it's own layer of distortion at lower volume.
This is an easy build kit with point to point wiring and clear, easy to follow instructions. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life. All you need to provide is solder, soldering iron and a few simple tools.
$39.95
Click to read more about this product.
K-960Effects Pedal Kit - MOD® Kits, The Trill, Tremolo
The Trill tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal.
Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged.
All you need to provide is solder and tools! Uses 9 volt battery which is not included.
$43.95
Click to read more about this product.
K-975Effects Pedal Kit - MOD® Kits, Ring Resonator, Octave-Up Fuzz
The Ring Resonator is the newest member of the MOD® Kits DIY family. Order now to be one of the first people to get this new octave up fuzz pedal!
The Ring Resonator kit is an octave up fuzz effect; an all analog design that captures those late '60s octave-up fuzz tones. Transformer coupled germanium diodes produce sounds that range from a subtle octave up to thick, harmonically rich sonic textures and synth-like tones. Experimenting with different pickups and tone control settings on your guitar with the Ring Resonator can also produce sitar-like sounds.
MOD® Kits are designed to give novice and experienced musicians the opportunity to build their own amps and effects pedals. All kits come with easy-to-follow instructions and use point-to-point wiring. A pre-drilled enclosure and all necessary parts are included. All you need to provide are hand tools, a soldering iron and solder.
The effect pedal operates on a 9V battery.
$64.95
Click to read more about this product.
P-L500Bezel with LED Lamp - 5mm, Red with holder
5 mm diameter Red LED with holder. Perfect for amps and effects. Mounts in a 5/16" diameter chassis hole.
$0.95
Click to read more about this product.
P-L200LED Holder - 3mm
Holder for LED.
$0.65
Click to read more about this product.
P-ECB-GEARGear - for Wah Potentiometer
Generic gear (a.k.a. pinion) for wah-style potentiometers. Outer diameter = 0.48", height = 0.61". Push-on for splined 1/4" shaft.
Push-on mounting allows any 1/4" splined shaft potentiometer to be equipped for use with rack and pinion shaft rotation as in a wah pedal.
$1.50
Click to read more about this product.
P-L400LED Holder - 3mm, Red LED

Bezel Assembly with 3mm Red LED. Required hole size: 0.25". Washer and hex nut included. LED Specifications: Color Red Lens Diam 3 mm Overall Height 5.4 mm Lens Type Diffused Luminous Intensity Min. 3.6 mCd @If (test) 10 mA Wavelngth (Peak) 568 nm V(FM) Max.(V) Forward Voltage 2.7 V @I(F) (test) 10 mA Min Operating Temp -30° Max Operating Temp 80°


$0.75
Click to read more about this product.
P-ECB-003Power Supply - Dunlop, 9V, 200mA, Barrel, Center Negative
AC Adaptor. Barrel type. 9 Volt. US. Original Dunlop replacement part.
$11.75
Click to read more about this product.

Pages

(12 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts