Pedal Parts / DIY

High quality crush-proof boxes that are perfectly sized for stompboxes. This cardboard box features triple wall sides and double wall front and bottom ensuring a safe housing for your pedals. The inside dimensions 6” x 4” x 3" fit 1590BB, 1590N1, and 125B. These boxes are ideal for storing or packaging effects pedals.

Bezel Assembly with 3mm Red LED. Required hole size: 0.25". Washer and hex nut included. LED Specifications: Color Red Lens Diam 3 mm Overall Height 5.4 mm Lens Type Diffused Luminous Intensity Min. 3.6 mCd @If (test) 10 mA Wavelngth (Peak) 568 nm V(FM) Max.(V) Forward Voltage 2.7 V @I(F) (test) 10 mA Min Operating Temp -30° Max Operating Temp 80°

High quality spiral shielded wire with a small outer diameter of 0.138 inches. Both the core wire and spiral shield are tinned copper so soldering is easy. The gray outside jacket and blue core insulation have a similar appearance to the type of wire used in vintage pedals such as the Supa Fuzz, Tone Bender, and Zonk Machine. The core wire is 7 strand 24AWG.

1N60 point-contact germanium diodes in a DO-7 package with striped clear glass. 1N60 diodes were used in many vintage electronics and also make for great clipping diodes in stompbox effects pedals.

The NJM4580D (JRC4580) is a dual opamp popularly used in many distortion pedals. This chip is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools. It is also suitable for the headphone amp at higher output current, and furthermore, it can be applied for the handy type set operational amplifier of general purpose in application of low voltage single supply type which is properly biased of the low voltage source. Features:

• Operating Voltage ±2V~±18V
• Low Input Noise Voltage 0.8µVrms typ.

Raised plastic chickenhead knob with brass insert and set screw. 1.20" in length. Davies 2300 clone.

Genuine Cliff barrel plug for use with 5.5mm / 2.1mm barrel jacks. This plug is great for repairing power supplies and making cables. The outside housing is made of a thick durable plastic.

This vintage knob design has been used on numerous boutique pedals. These classy knurled pointer knobs are made from a solid mold, feature a slotted set screw, and fit ¼" solid shaft potentiometers. Davies 1470 clone.

Large knob with line indicator and set screw similar in style to the Davies 1500 and 1510 knobs. Pairs well with P-K380X. Fits ¼” (6.35mm) pot shafts.

• Knob Height = 0.60"
• Pointer Diameter = 1.06"
• Fits 1/4" shaft with set screw
• Oversized Davies 1510 Clone

Prewired cone-shaped LED bezel. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12VDC. Mounting nut and lock washer included.

PCB for converting SMD QFN-32 packages to through hole DIP-32 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.

Polyester Film Capacitor used in MOD® Pedal Kits. Rated at 0.1µF 50V. Tolerance: 10%. Operating temperature: -40 C to +85 C

Large plastic knobs with set screw and brass insert. Similar to the knobs used on many classic Dunlop / MXR pedals. These knobs have a fluted grip with an indicator line as well as a dot indicator on the skirt. Fits ¼” (6.35mm) pot shafts.

Prewired cup-shaped LED bezel with a red LED. An internal current limiting resistor is installed in this bezel and it can be used with voltages up to 12V. Mounting nut and lock washer included.

CD4024B is a 7-stage ripple-carry binary counter. All counter stages are master-slave flip-flops. The state of a counter advances one count on the negative transition of each input pulse; a high level on the RESET line resets the counter to its all zeros state. Schmitt trigger action on the input-pulse line permits unlimited rise and fall times.

The CD4077B contains four independent Exclusive-NOR gates. The CD4077B provides the system designer with a means for direct implementation of the Exclusive-NOR functions, respectively. Features:

• High-Voltage Types (20V Rating)
• CD4077B - Quad Exclusive-NOR Gate
• Medium Speed Operation
• tPHL, tPLH = 65ns (Typ) at VDD = 10V, CL = 50pF
• 100% Tested for Quiescent Current at 20V
• Standardized Symmetrical Output Characteristics
• 5V, 10V and 15V Parametric Ratings
• Maximum Input Current of 1µA at 18V Over Full Package Temperature Range
• 100nA at 18V and 25°C
• Noise Margin (Over Full Package Temperature Range)
• 1V at VDD = 5V, 2V at VDD = 10V, 2.5V at VDD = 15V
• Meets All Requirements of JEDEC Standard No.

Threaded through wide dress nuts for use with mini toggle switches. This wide based nut is not capped allowing the nut to thread past the top of the switch’s bushing. The uncapped top can be useful where internal depth is an issue such as parallel PCB mounting. These plated dress nuts feature a wide chamfered edge for a professional and unique look. These work on any 1/4-40 UNS threaded bushing. Two sides are flatted for use with a tool when fastening.

Large vintage style skirted pointer knob. This knob is styled after the RCA “fester” knobs found on countless vintage electronics. The knobs feature a hex set screw, and fit ¼" solid shaft potentiometers.

NE5534 single op amp in an 8-pin DIP package. The NE5534 device is a high-performance operational amplifier combining excellent dc and ac characteristics. Some of the features include very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, and high slew rate. These operational amplifiers are compensated internally for a gain equal to or greater than three. Optimization of the frequency response for various applications can be obtained by use of an external compensation capacitor between COMP and COMP/BAL.

Alpha Mini Pots with solid shaft and short PC mount terminals.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 3.8 mm (0.150”)
• Lead Distance from shaft center: 12.5 mm + 3.5 mm (0.492” + 0.138”)
• Lead Thickness: 0.5 mm (0.020”)

Premium 9V battery clip made of a rigid plastic frame with an insulating wall enclosing the battery terminals. This high quality battery snap features nickel-plated brass contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.

Premium 9V battery clip with a rigid plastic frame. This high quality battery snap features nickel-plated phosphor bronze contacts. The six inch leads are 26 AWG stranded wire, prestripped and tinned for an easy installation.

Mid-sized black plastic control knob with set screw and brass insert. This knob is similar in appearance to the classic MXR knobs but with a smaller diameter. It features a fluted grip with an indicator line along with a small skirt with a dot indicator. Fits ¼” (6.35mm) pot shafts.

Single row of 9 U-style terminals on a black board. The U-style terminal strips are spaced 8.3mm apart allowing for more densely populated point-to-point builds. The boards are 0.063” thick.