Pedal Parts / DIY

Transistor Set - tested and selected for Fuzz Face, 2N1309, PNP, Germanium
This is a set of two 2N1309 germanium transistors that have been hand-selected to work in the germanium Fuzz Face circuit. Also included are 4 metal film resistors to use in the circuit. In most cases, the values have been modified from the stock values slightly to ensure that the collector of Q2 biases to roughly -4.5V. A data sheet containing the schematic and the resistor values is included so that you can use your own resistor type if you would prefer. There is a range of bias voltages that can sound nice in a Fuzz Face, and voltages in original units varied. These transistors have been tested with bias voltage, sound, and noise level in mind. Note that due to a variety of factors such as battery/PSU voltage, temperature, and component tolerance, the voltage on the collector of Q2 may not measure at exactly -4.5V, but it should be close in a properly-built circuit.
$24.95
Chassis Box - Hammond, 1590TRPB, Short Trapezoid, 4.41 x 3.11 x 1.54", Hammered Blue
Limited Run!
Short trapezoid shaped Hammond enclosure in a hammered blue powdercoat. This style is reminiscent of vintage fuzz pedals. Screws included. Key Features:
  • Hammered blue powdercoat
  • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Four 6-32 x 1/2” machine screws secure lid - into factory tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$24.95
Out of Stock
Power Supply - Power-All® ECO-Dapter®, 9V, 2000mA, for Effects Pedals
Power-All® ECO-Dapter® is a center negative 9VDC power supply for effects pedals that can supply up to 2000mA of power making it a great choice for pedals boards and power hungry effects.
$24.35
Chassis Box - YY, Diecast, Slanted, 4.65" x 3.70" x 1.66"
Colors Available:
Slanted YY enclosures perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features
  • Vintage style slant
  • Flat top-section for mounting controls
  • Recessed lid
  • Thick diecast construction
Starting at $23.95
Potentiometer - Dunlop Hot Potz, 470 kΩ
Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.
$23.50
Chassis Box - Hammond, 1590D, Diecast, 7.39" x 4.71" x 2.05"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$23.45
Chassis Box - Hammond, 1590V, Diecast, 4.70" x 4.70" x 3.54"
Special Order Item
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$23.00
Out of Stock
Relay Module - Lehle, Relay True Bypass Switching Unit
The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.
Starting at $22.95
Integrated Circuit - Xvive, MN3005, BBD, 4096 Stage
The XVive MN3005 is a drop-in replacement for the original Panasonic 4096-stage MN3005 BBD chip used in many delay pedals and effects. Xvive Audio’s first-ever product was the MN3005: a re-creation of the legendary bucket brigade chip used in the Deluxe Memory Man and many other iconic effect pedals and instruments. Now, the Xvive MN3005 is at the heart of delay pedals produced by some of the world’s top effect pedal brands. The MN3005 is the world’s first 4096-stage long-delay BBD—eight times longer than the 512-stage BBD. It is manufactured using a P-channel low-noise silicon gate process. A long-signal delay time of 205 ms can be obtained at a clock frequency 10 kHz, with a sound-to-noise ratio of 75dB. This ratio is an improvement of 20dB, as compared to eight connected 512-stage BBDs!
$22.95
DSP Module - ABE, Accu-Bell Effector, 3 Adjustable Effects
The Accu-Bell Effector offers reverb, chorus, and delay with adjustable setting and tap tempo. This module runs on 5.5V to 9.5V DC so it is easy to incorporate into effect pedal builds. Please see the attached datasheet for an example schematic.
$21.95
Potentiometer - Dunlop, Hot Potz II Crybaby, 100 kΩ
Hot Potz II Crybaby Pot. for newer Crybaby models. Made by Beckman. 100 kΩ. Original Dunlop replacement part. The same tone and sweep characteristics as the original Cry Baby Hot Potz potentiometer with low wiper noise and extended life.
$20.95
Resistor Kit - ⅛ Watt, Metal Film, 1% tolerance, 5 of each value
Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet.
$20.70
package of 230
Pliers - Xcelite, serrated jaw, 5.5", Long Reach
5 1/2" Overall Length, 1 1/2" Jaw Length Product Features:
  • Thin profile, long reach pliers
  • For access into tight spaces
  • Lightweight for maximum comfort
  • For use in precision electronic assembly applications
  • Features serrated jaws
  • Features red grips
$20.39
Chassis Box - Hammond, 1590DD, Diecast, 7.40" x 4.72" x 1.30"
Hammond Mfg. Diecast Aluminum Chassis Box – 7.4” x 4.7” x 1.3”. Made in Taiwan. Key Features: • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
$20.25
On Backorder
Chassis Box - GØRVA Design, C65, Diecast, 4.72” x 2.56” x 1.54”, Hammered Blue
Limited Run!
The Gorva C65 is a high quality powder-coated take on the Hammond 125B size enclosure with a focus on function and design. Features:
  • Hammerted Blue powdercoat
  • Slightly beveled top and rounded corners for high quality look.
  • Tight fit and small gap between the enclosure and lid.
  • Undercut boss allows more internal room for more flexible layout.
  • Smooth, eggshell-like matte powder coating.
  • Recessed bottom lid

Part of a limited run of hammered blue enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-BLU 1590N1 / 125B P-H1590N1CE-HMT-BLU C65 (Gorva) P-H1590N1-GORVA-HMT-BLU S90 (Gorva) P-H1590BB-GORVA-HMT-BLU YY P-H-YY-HMT-BLU 1590TRPD Trapezoid P-H1590TRPB-HMT-BLU
$19.95
Out of Stock
Battery Box - Gotoh, BB-04W, Dual, for 9 volt batteries
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.
$19.95
Knob - Fender®, Black Chicken-Head
Original Fender chicken head knob. Black, comes in a package of six. Set screw. For 1/4" solid shaft pots.
$19.95
package of 6
Integrated Circuit - Experimental Noize FXCore, DSP, Multi-Effect / Reverb
FXCore from Experimental Noize is a DSP designed for creating audio effects in pro-audio devices. FXCore can operate as a standalone device when paired with appropriate CODECs where it generates all necessary clocks or as part of a more complex system where it will lock to the word clock and bit clock provided by another part of the system.
FXCore can store up to 16 programs and their associated register preset values in its internal FLASH memory so no external program storage is required.
$19.95
Chassis - Three Knob Fuzz, Pressed Steel
Pre-drilled three knob pedal enclosure made of pressed steel. This large enclosure is a close match to the original enclosures found on various vintage fuzz effects such as the Vox Tone Bender MKIII, Rotosound Fuzz, and Park Fuzz Sound. It features three holes for potentiometers, two top mounted holes for ⅜” jacks, and a footswitch hole. Comes with 4 rubber feet and a pack of mounting screws(packaged separately) for attaching the bottom plate.
  • Footswitch Hole Diameter: 0.492 in. (12.5mm)
  • Potentiometer Hole Diameter: 0.294 in. (7.47mm)
  • Jack Hole Diameter: 0.447 in. (11.35mm)
$19.95
Potentiometer - Dunlop, 250 kΩ Audio, for Dunlop GCB80
250 kΩ gear shaft pot with an audio taper. Original Dunlop replacement part. Used in the Dunlop GCB80 High Gain Volume Pedal.
$19.95
Chassis Box - Hammond, 29830PSLA, Eddystone 1590BB, Diecast, 4.7” x 3.7” x 1.3”
Eddystone 29830PSLA enclosure with similar dimensions to the Hammond 1590BB enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590BB style builds.
  • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
  • Aluminum alloy to BS1490, LM2M - supplied in natural finish.
  • Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
  • Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
  • Countersunk lid holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
$18.95
Wire Stripper / Cutter - Xcelite, 5", with Cushion Grip Handle
5" wire stripper & cutter with cushion grip handles. Features:
  • Cuts and strips both solid and stranded wire cleanly, neatly.
  • Adjustable screw stop for different wire sizes.
  • Hardened with ground blades.
  • Red plastic-coated cushion grip provides maximum leverage.
  • Strips 8AWG - 22AWG wire.
$18.95
Inductor - Dunlop, Fasel, Toroidal with Cup Core Tone, Yellow
This yellow fasel is a Toroidal design with the tonal character of a cup core, best for attaining a vintage vibe. Use the precision-wound Toroidal, part number P-ECB-FI-02, for the cleanest sound possible. The Fasel inductor is back! These near-mythical inductors are the key to the singing tonal sweep every wah player lusts for but can't capture with a new pedal. The ultimate upgrade to your current wah, these magic bullets are available exclusively from Dunlop, the new worldwide agent for Fasel of Italy. Your wah will finally give up the lush harmonic sparkle you've always heard in your head but could never coax from your rig.
$18.95
Chassis Box - GØRVA Design, S90, Diecast, 4.61" x 3.54" x 1.38", Hammered Blue
Limited Run!
The Gorva S90 is a high quality hammered blue powder-coated take on the Hammond 1590BBM size enclosure with a focus on function and design.
Features:
  • Hammered Blue powdercoat
  • Beveled top and rounded corners for high quality look.
  • Tight fit and small gap between the enclosure and lid.
  • Undercut boss allows more internal room for more flexible layout.
  • Smooth, eggshell-like matte powder coating.
  • Add 0.16" to enclosure depth for lid.

Part of a limited run of hammered blue enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-BLU 1590N1 / 125B P-H1590N1CE-HMT-BLU C65 (Gorva) P-H1590N1-GORVA-HMT-BLU S90 (Gorva) P-H1590BB-GORVA-HMT-BLU YY P-H-YY-HMT-BLU 1590TRPD Trapezoid P-H1590TRPB-HMT-BLU
$18.95
Out of Stock