You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
P-H552Footswitch - Carling, SPST, Off-(On), Solder Lugs
Carling, SPST footswitch, momentary Off-(On), normally open with solder lugs.

Note: Off-(On) switches may sometimes be referred to as Off-None-(On).
$7.95
Click to read more
P-ECB-244Battery Box - Dunlop, snap-in

Original Dunlop snap-in, black battery box with snap-closed swing door for effects pedals using one 9 volt battery (accessed via the bottom of the pedal). Cutout dimensions: 2.46" x 1.27", box depth: 0.70", snaps over a panel thickness of about 0.04". Used on Dunlop Cry Baby Wah Wah GCB95 and many Dunlop effects pedals.


$1.75
Click to read more
P-ECB-25PC Board - Dunlop, for Crybaby

Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.


$21.95
Click to read more
P-H1590BChassis Box - Hammond, Unpainted Aluminum, 4.37" x 2.37" x 1.22"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$7.07
Click to read more
P-ECB-24APotentiometer - Dunlop Hot Potz, 470K

Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470K ohm. Original Dunlop replacement part.


$20.95
Click to read more
P-H1590AChassis Box - Hammond, Unpainted Aluminum, 3.64" x 1.52" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$6.22
Click to read more
P-ECB-130Knob - Dunlop, MXR Knob for Pedal

Large MXR knob with set screw for MXR pedals. Original Dunlop replacement part. Skirted knob with white line and dot indicator.


$2.95
Click to read more
P-H1590CChassis Box - Hammond, Unpainted Aluminum, 4.72" x 3.70" x 2.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$11.32
Click to read more
P-H1590BBChassis Box - Hammond, Unpainted Aluminum, 4.67" x 3.68" x 1.18"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$9.42
Click to read more
P-H1590LBChassis Box - Hammond, Unpainted Aluminum, 1.99" x 1.99" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$6.14
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts