You are here

Effect Pedals & Parts

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(12 pages)
P-H410-AFootswitch - Quad Pole, Double Throw (4PDT), Black, 12 Pins
4PDT latching footswitch with 12 solder lugs.
$3.25
Click to read more about this product.
P-ECB-25PC Board - Dunlop, for Crybaby

Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.


$21.95
Click to read more about this product.
K-920Effects Pedal Kit - MOD® Kits, The Piledriver, Power Boost

"The PileDriver" is a clean boost kit that will provide up to 38dB of gain to your guitar signal. Use it to push your preamp into overdrive or as a line driver if you are experiencing signal degradation from your effects chain. This is a simple kit and great for beginners!


$24.95
Click to read more about this product.
P-ECB-124Grommets - Dunlop, Offset, 3x4 Different Sizes
Original Dunlop offset grommets (i.e. rubber bumpers) used on the underside of the treadle piece (rocking structure) of wah pedal enclosures. Made in USA.
$3.95
Click to read more about this product.
P-H1590BCEChassis Box - Diecast Aluminum, 4.39" x 2.34" x 1.06"

4.39" x 2.34" x 1.06" D. Equivalent to Hammond P-H1590B.


$5.95
Click to read more about this product.
P-H1590BBCEChassis Box - Diecast Aluminum, 4.7" x 3.7" x 1.18"

Same as Hammond P-H1590BB but a generic manufacture from Taiwan. 4.7" x 3.7" x 1.18" depth.


$8.95
Click to read more about this product.
P-H1590N1CEChassis Box - Diecast Aluminum, 4.77" x 2.60" x 1.39"
Equivalent to Hammond P-H1590N1. Measures 4.77" x 2.60" x 1.39".
$6.25
Click to read more about this product.
P-H1590AChassis Box - Hammond, Unpainted Aluminum, 3.64" x 1.52" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$5.93
Click to read more about this product.
M-PAS-DKit - Power All System deluxe, for effects pedals
The Power-All Deluxe Kit provides 9 volts DC at 2000 milliamps @ more than enough current to power dozens of effect pedals, including up to 4 Line 6 Modelers! The Power-All Deluxe Kit can power eleven pedals out of the box, and comes complete with a variety of jumper cables that allow connection of phone plug, reverse polarity, digital, and battery-only pedal types.
$39.95
Click to read more about this product.
P-H1590BChassis Box - Hammond, Unpainted Aluminum, 4.37" x 2.37" x 1.22"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$6.73
Click to read more about this product.

Pages

(12 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts