Pedal Parts / DIY

High quality spiral shielded wire with a small outer diameter of 0.138 inches. Both the core wire and spiral shield are tinned copper so soldering is easy. The gray outside jacket and blue core insulation have a similar appearance to the type of wire used in vintage pedals such as the Supa Fuzz, Tone Bender, and Zonk Machine. The core wire is 7 strand 24AWG.

Audio taper (log), vertical mount, Alpha pots with a 6mm D shaft. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.

Low profile mono jacks made by Lumberg. These high quality jacks are the perfect size for tightly packed pedal enclosures. The premium look, feel, and construction make Lumberg jacks an excellent choice for any build.

• M9*0.75 Bushing Thread
• Mono 2-Conductor
• Open Circuit (does not have switched terminal).
• Includes nut and washer.

Cliff UK 1/4" white jack. External threading: 7/16-20. Ni-Ag® Alloy Self-Cleaning Contacts for superior performance and reliability. Tough, molded Nylon body.

PCB for a Fuzz Face style circuit with PCB mounted potentiometers. Its very low component count makes it a great beginner project. Builders can use preselected transistors from P-Q2N1309-SET-FF with its included resistors for R1 through R4 for a simple and great sounding germanium fuzz. If a builder wants to use their own transistors, the stock component values are also clearly labeled on the PCB. The transistor footprints fit P-SGP-001 sockets making swapping transistors a simple process so builders can experiment with a variety of types and values. This board was designed for a 1590N1/125B or C65-sized enclosure, with the potentiometers spaced 30mm apart. It can also be mounted using the two screw-mount holes with the potentiometers wired off-board. There are two screw-mounting holes which are designed for M3 screws.

Nylon flat washers for use with foot switches. These washers are M12 size and fit both metric (M12) and imperial (15/32) bushings for compatibility with the vast majority of foot switches.

The AS3080E is Alfa’s version of the CA3080 IC. The AS3080E is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080E has differential input and a single-ended, push-pull, class A output. Amplifier bias
input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080E is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.

Included in the PA-9ECB Basic Kit and also sold separately, the Cable-Grey allows the user to power vintage and boutique effect units that run off 9-volt batteries but do not have an external AC power jack. The Cable-Grey hooks directly to the unit's Battery Snap and can be connected to any of the Power-All daisy chains, or directly to the Power-All.

Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.

BC148C NPN transistor in a rare Mullard Lockfit package. The BC148C is the equivalent of a BC108C but in the Lockfit package rather than a TO-18. The BC148C was used in a variety of audio and radio equipment and works well for fuzz and other effects.

TLC274 quad op amp in a 14-pin DIP package. The TLC274 quad operational amplifier combines a wide range of input offset voltage grades with low offset voltage drift, high input impedance, low noise, and speeds approaching that of general-purpose BiFET devices. These devices use Texas Instruments silicon- gate LinCMOSTM technology, which provides offset voltage stability far exceeding the stability available with conventional metal-gate processes. The extremely high input impedance, low bias currents, and high slew rates make these cost-effective devices ideal for applications which have previously been reserved for BiFET and NFET products.

Linear taper, vertical mount, Alpha pots with a 6.35mm shaft diameter. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.

The NJM5532 is a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM1458, it shows better noise performance, improved output drive capability, and considerably higher small-signal and power bandwidths. it is compensated internally for voltage follower circuit. This makes the device especially suitable for application in high quality and professional audio equipment, instrumentation, control circuits, and telephone channel amplifiers Features:

• Operating Voltage = ±3V~±22V
• Small Signal Bandwidth = 10MHz typ.
• Output Drive Capability = 600Ω,10Vrms typ.
• Input Noise Voltage = 5nV/√Hz typ.
• Power Bandwidth = 140kHz typ.
• Slew Rate = 8V/µs typ.
• Bipolar Technology

CD4030B types consist of four independent Exclusive-OR gates. THe CD4030B provides the system designer with a means for direct implementation of the Exclusive-OR function. Features:

• Medium-speed operation—tPHL, tPLH = 65 ns (typ.) at VDD = 10 V, CL = 50 pF
• 100% tested for quiescent current at 20 V
• Standardized, symmetrical output characteristics
• 5-V, 10-V, and 15-V parametric ratings
• Maximum input current of 1 µA at 18 V over full package-temperature range; 100 nA at 18 V and 25°C
• Noise margin (over full package-temperature range) =
  
  • 1 V at VDD = 5 V
  • 2 V at VDD = 10 V
  • 2.5 V at VDD = 15 V
• Meets all requirements of JEDEC Tentative Standard No.

The AS301AH is Alfa’s version of the LM301A in an 8 pin TO5 package. The AS301A is a general purpose operational amplifier. This amplifier offers many features which make its application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, and freedom from oscillations and compensation with a single 30 pF capacitor. It has advantages over internally compensated amplifiers in that the frequency compensation can be tailored to the particular application. For example, in low frequency circuits it can be overcompensated for increased stability margin. Or the compensation can be optimized to give more than a factor of ten improvements in high frequency performance for most applications. In addition, the device provides better accuracy and lower noise in high impedance circuitry.

Large black plastic control knob with set screw and brass insert. This distinctive pointer knob is similar to the selector knobs used on original MiniMoog and Moog modular synths. It features a triangular pointer, a radial brushed metal top, and a line indicator. The large skirt has a diameter of 1.125 inches. Fits ¼” (6.35mm) pot shafts.

Switchcraft Type 12B Littel-Jax stereo phone jack. Mates with standard ¼" plugs and is available with 0.25" inside diameter bushing. Stereo 3-Conductor double open circuit (does not have switched terminal). Includes nut and washer.

YY enclosure finished in a hammered silver powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Hammered silver powdercoat
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

L78L33 3.3V regulator in a TO-92 package. The L78L33 three-terminal 3.3V positive regulator employs internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78L series used as Zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise. Features:

• Output voltage of 3.3V
• Output current up to 100 mA
• Short-circuit protection
• No external components are required

The Gorva Design M45 enclosure has similar dimensions to 1590A but a bit larger for practical use. It measures 100mm [3.94"] x 45mm [1.77"] x 35 mm [1.38"]. The extended dimensions allow for easier builds and top mounted jacks. Features:

• Slightly beveled top and rounded corners for a high quality look.
• Tight fit and small gap between the enclosure and lid.
• Undercut boss allows more internal room for a more flexible layout.
• Smooth, eggshell-like matte powder coating.
• Recessed bottom lid

Uniquely shaped trapezoid Hammond enclosure. Screws included.

Atten AT-E33A heavy duty desoldering pump. This pump’s design provides a high vacuum force especially helpful for clearing circuit boards in rework jobs and field repair. Features

• Piston with double oil seals
• Handle delivers comfortable grip and non-slip function.
• Compact size
• Anti-rust spring
• Built-in tip for easy replacement
• Quick and easy cleaning

High-quality Bourns 3362P trimpots. These single-turn cermet trimmers can be found in countless guitar pedals and synthesizer modules. Sealed trimmers are built with an o-ring seal to prevent entrance of moisture and serve as a mechanical restraint to prevent unwanted wiper movement. ±10% tolerance.

ECB233 boost / distortion kick switch. Original Dunlop replacement part. Used in the SW95 Crybaby Slash Wah. Through hole PCB mount.