You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results

Pages

(13 pages)
P-ECB-130Knob - Dunlop, MXR Knob for Pedal

Large MXR knob with set screw for MXR pedals. Original Dunlop replacement part. Skirted knob with white line and dot indicator.


$3.45
Click to read more
P-H1590CChassis Box - Hammond, Unpainted Aluminum, 4.72" x 3.70" x 2.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$11.32
Click to read more
P-H1590BBXChassis Box - Hammond, Aluminum, 4.67" x 3.68" x 1.18"
Colors Available:
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

Starting at $9.42
Click to read more
P-ECB-40Jack - Dunlop, ¼", Stereo, for effects pedals

Stereo jack for Dunlop effects pedals. Original Dunlop replacement part. Though hole PCB mount with six pins.


$3.35
Click to read more
P-H1590LBChassis Box - Hammond, Unpainted Aluminum, 1.99" x 1.99" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$6.14
Click to read more
K-980Effects Pedal Kit - MOD® Kits, The Persuader Deluxe, Overdrive

The Persuader Deluxe utilizes a Darlington preamp to push cascaded triode vacuum tubes into distortion. Four dual triode vacuum tubes are included with each kit (JJ 5751, 12AX7B China, JJ 12AU7 and a NOS USA-made 12AT7). Swap to create a wide range of tones from just a hint of break up from the JJ 5751 to over the top crunchy distortion using the NOS US made 12AT7. A boost switch provides an additional layer of flexibility with added gain and a little extra bottom end. An LED indicator lights up when the Persuader Deluxe is engaged and not in true bypass mode. Operates on a 9V battery or AC adapter, which is not included. When completed, this pedal draws considerable current and battery life will be short. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.


$99.95
Click to read more
P-ECB-129Tread - Dunlop, rubber, replacement for Wahs

Genuine Dunlop replacement tread pad for Cry-Baby wah pedals. Adhesive backed for easy installation and labeled on top surface to indicate amplifier and instrument inputs.


$2.95
Click to read more
P-ECB-31Felt Pad - Dunlop, replacement for Wahs
Replacement Dunlop felt pad for use with wah pedals. This circular felt pad has an adhesive side for an easy installation. The pad is typically installed on the underside of the pedal directly above the footswitch to cushion the contact when switching the wah on and off. Made in USA.
$1.25
Click to read more
K-970Effects Pedal Kit - MOD® Kits, The Tea Philter, T Filter

The Tea Philter - A T-Filter Pedal Kit The Tea Philter pedal produces a fixed wah tone allowing you to lock it in without rocking the pedal back and forth. Every guitar/wah combination has a certain sweet spot that is perfect for lead and chord work. The Tea Philter lets you dial in everything from your favorite vocal mid-range tone to thick lows. Using point-to-point wiring and easy-to-follow instructions you can have a working fixed wah pedal in a matter of hours. The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately.


$31.95
Click to read more
P-H1590BBCE-XChassis Box - Diecast Aluminum, 4.67" x 3.68" x 1.18"
Colors Available:

Chassis box perfectly suited for effects pedals and other DIY projects.


Starting at $8.95
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts