Pedal Parts / DIY

Switch Accessory - Mini Toggle Caps
Colors Available:
Rubber caps / switch tips for mini toggle switches in a variety of colors. These are made for standard sized toggle bats.
Starting at $0.59
Switch - DIP, Slide, 0.1" Spacing
DIP slide switches with standard 0.1” (2.54mm) lead spacing. These small PCB mounted switches are used in many circuits such as mode settings in effects pedals. Specifications:
  • Contact Rating: 100mA 50VDC
  • Terminal: Brass with gold plating
  • Dielectric strength: 500VAC 1 minute
  • Insulation Resistance: 100mΩ min (500VDC)
  • Electrical Life: 2,000 cycles per position
  • Contact Resistance: 500mΩ max
  • Mechanical Life :≥100,000 Cycles
  • Operating Temperature :-25°C to +85°C
$0.59
LED Lens - Fresnel, Polycarbonate, 5mm
Colors Available:
Panel mount led lenses made of high quality polycarbonate. These lenses provide a clean semi-flush appearance with a small panel footprint and work well in any project using LED indicators. Features:
  • ¼” mounting hole
  • For panel thicknesses of 1/16” to ⅛”
  • Fresnel lens
  • Low Profile

For a version that fits 3mm LEDs, see P-L310-X.
Starting at $0.59
Standoff - M3, Male-Female, Aluminum, 5.5mm Diameter
  • Finish/Plating: Clear Iridite
  • Material: Aluminum
  • OD: 5.5mm
  • Shape: Hex (Metric)
  • Style: M-F Standoff
  • Thread Depth(D): 8mm
  • Thread Length (TL): 8mm
  • Thread: M3
  • Type: Threaded Standoffs
Starting at $0.60
Washer - Internal Tooth Lock, spring steel
Spring steel tooth-lock washer. Uses internal teeth for locking and tension.
Starting at $0.60
package of 5
Capacitor - 50V, Radial Lead, Electrolytic
High quality, radial leaded, aluminum electrolytic capacitors rated at 50VDC.
$0.60
package of 5
Capacitor - 50V, 680pF, Ceramic Disc
Ceramic disc capacitor, 680 pF (.00068µF) rated for up to 50 V.
Non linear temperature coefficient of capacitance
$0.60
Power Jack - DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
½" panel mount DC jack with solder lugs. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. Round plastic with normally closed switch. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch.
$0.64
Power Jack - DC PC Mount, 5.5mm External, 2.1mm Internal
This PCB mounted DC jack style can be found on many manufacturers’ pedals. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder pins are available for tip, ring, and switch.
$0.64
Power Jack - DC Panel Mount, Vintage Boss Style, 5.5mm External, 2.1mm Internal
This DC power jack is similar to those used on vintage MIJ Boss pedals and others. This jack has a 2.1mm pin for use with 5.5mm barrel plugs. Three solder lugs are available for tip, ring, and switch.
$0.64
Finishing Nut - For ⅜” Jacks and Pots, ⅜”-32 UNEF-2A
Colors Available:
High quality plated ⅜” nuts for jacks and potentiometers. These nuts are perfect for amplifier, pedal and synthesizer builds with high aesthetics or color theming. The ⅜”-32 UNEF-2A threading fits many ⅜” bushing parts such as Switchcraft ¼” jacks and CTS pots.
Starting at $0.64
package of 5
Cloth Pedal Bag - 3” x 5”, 100% Cotton
Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 3 in. x 5 in. and fit 1590A stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.
$0.65
LED Lens - Flat Cylindrical, Fresnel, Polycarbonate, 5mm
Colors Available:
Panel mount LED lenses made of high quality polycarbonate. These flat cylindrical lenses provide a unique retro appearance with a small panel footprint and work well in any project using LED indicators. Features:
  • ¼” mounting hole
  • For panel thicknesses of 1/16” to ⅛”
  • Fresnel lens
  • Flat cylindrical shape
  • Fits standard 5mm LEDs
Starting at $0.65
Op-Amp - NE5532, Dual, Low Noise, Audio, 8-Pin DIP
NE5532 dual op amp in an 8-pin DIP package. The NE5532 device is a high-performance operational amplifier combining excellent DC and AC characteristics. They feature very low noise, high output-drive capability, high unity-gain and maximum-output-swing bandwidths, low distortion, high slew rate, input-protection diodes, and output short-circuit protection. These operational amplifiers are compensated internally for unity-gain operation. These devices have specified maximum limits for equivalent input noise voltage. Features
  • Equivalent Input Noise Voltage: 5 nV/√Hz Typ at 1 kHz
  • Unity-Gain Bandwidth: 10 MHz Typ
  • Common-Mode Rejection Ratio: 100 dB Typ
  • High DC Voltage Gain: 100 V/mV Typ
  • Peak-to-Peak Output Voltage Swing 26 V Typ With VCC± = ±15 V and RL = 600 Ω
  • High Slew Rate: 9 V/μs Typ
$0.65
Capacitor - 25V, Radial Lead, Electrolytic
High quality, radial leaded, aluminum electrolytic capacitors rated at 25VDC.
Starting at $0.65
package of 5
9V Battery Cushion - Vinyl Foam Tape, 3M, ½” x 2”
1/2 inch by 2 inch adhesive foam strip for cushioning 9V batteries in pedal enclosures. This black, medium density foam used an acrylic adhesive and paper liner. The high quality 3M materials ensure a durable foam and lasting adhesive. Made with ¼ inch thick foam.
$0.65
CMOS - CD4016, Quad Bilateral Switch, 14-Pin DIP
CD4016B Series types are quad bilateral switches intended for the transmission or multiplexing of analog or digital signals. Each of the four independent bilateral switches has a single control signal input which simultaneously biases both the p and n device in a given switch on or off. Features:
  • 20-V digital or ± 10-V peak-to-peak switching
  • 280- typical on-state resistance for 15-V operation
  • Switch on-state resistance matched to within 10 typ. over 15-V signal-input range
  • High on/off output-voltage ratio: 65 dB typ. @ fis = 10 kHz, RL = 10 k
  • High degree of linearity: <0.5% distortion typ. @ fis = 1 kHz, Vis = 5 Vp-p, VDD–VSS
  • Extremely low off-state switch leakage resulting in very low offset current and high effective off-state resistance: 100pA typ.
$0.65
Op-Amp - LM3900, Quad, Norton, 14-Pin DIP
LM3900 quad op amp in a 14-pin DIP package. These devices consist of four independent, high-gain frequency-compensated Norton operational amplifiers that were designed specifically to operate from a single supply over a wide range of voltages. Operation from split supplies is also possible. The low supply current drain is essentially independent of the magnitude of the supply voltage. These devices provide wide band- width and large output voltage swing. Features
  • Wide Range of Supply Voltages, Single or Dual Supplies
  • Wide Bandwidth
  • Large Output Voltage Swing
  • Output Short-Circuit Protection
  • Internal Frequency Compensation
  • Low Input Bias Current
  • Designed to Be Interchangeable With National Semiconductor LM2900 and LM3900, Respectively
$0.65
Op-Amp - TL084, Quad, Wide Bandwidth, JFET-input, 14-Pin DIP
TL084 quad op amp in a 14-pin DIP package. These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage ( BI-FET II™ technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth.
$0.65
Potentiometer Adapter Sleeve - Converts 6mm or 18T shaft to ¼"
This brass adapter sleeve converts a 6mm shaft potentiometer or 18T knurled shaft potentiometer to 1/4" shaft (6.35mm), allowing for 1/4" knobs to be used on a wider range of potentiometers. 1/4" tall.
$0.65
CMOS - CD4027, Dual J-K Flip-Flop, 16-Pin DIP
CD4027B is a single monolithic chip integrated circuit containing two identical complementary-symmetry J-K flip flops. Each flip-flop has provisions for individual J, K, Set, Reset, and Clock input signals. Buffered Q and Q signals are provided as outputs. This input-output arrangement provides for compatible operation with the CD4013B dual D-type flip-flop. The CD4027B is useful in performing control, register, and toggle functions. Logic levels present at the J and K inputs along with internal self-steering control the state of each flip-flop; changes in the flip-flop state are synchronous with the positive-going transition of the clock pulse.
$0.65
Screw - 6-32, Phillips, Pan Head, Machine, Zinc
Phillips panhead machine screw, 6-32, zinc. Phillips panhead machine screw, 4-40, zinc. Designed to go through a hole or nut that is pre-tapped to form a mating thread for the screw. Has a general purpose bearing area and can be substituted in most applications for round, truss, or binding heads. Phillips drive is the most common drive used and is designed to "camout" when the screw reaches optimum tightness, thus preventing damage to the screw head.
Starting at $0.65
package of 5
Op-Amp - µA741, Single, Offset Null, 8-Pin DIP
µA741 single op amp in an 8-pin DIP package. The µA741 device is a general-purpose operational amplifier featuring offset-voltage null capability. The high common-mode input voltage range and the absence of latch-up make the amplifier ideal for voltage-follower applications. The device is short-circuit protected and the internal frequency compensation ensures stability without external components. A low-value potentiometer may be connected between the offset null inputs to null out the offset voltage. Features
  • Short-Circuit Protection
  • Offset-Voltage Null Capability
  • Large Common-Mode and Differential Voltage Ranges
  • No Frequency Compensation Required
  • No Latch-Up
$0.65
Op-Amp - NJM4580L, Dual, Audio, 8-Pin SIP
NJM4580L dual op amp from JRC in a SIP8 package. The NJM4580L is the same as the DIP NJM4580 (JRC4580) otherwise. The SIP version is a great replacement for dual op amps in vintage circuits as well as a space saving package for some PCB layouts. The NJM4580 is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, and it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools.
$0.69