You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

 

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(14 pages)
M-PAS-SPower Supply - Power-All System, 9V, 2000mA, for Effects Pedals

The PA-9 Power-All is the world's first 2000 mA, single outlet power supply designed specifically for guitar effect users. Don't waste money on batteries or take up valuable space with multiple "wall wart" adaptors or power bricks - the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All's special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9S now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.


$19.95
$17.96
You save: 10%
Click to read more
P-H503Switch - Footswitch, DPDT, Momentary, Solder Lugs

DPDT momentary footswitch. AC125V/4A AC250V/2A


$4.15
$3.74
You save: 10%
Click to read more
K-955Effects Pedal Kit - MOD® Kits, Thunderdrive Deluxe, Overdrive
The Thunderdrive Deluxe is an overdrive pedal kit that will provide a strong clean signal boost in the early gain settings and smooth distortion at maximum gain settings. Adjusting volume control and gain controls provides a wide variety of tones in spite of it's simple contruction.
The Turbo switch provides an additional boost in volume and less internally generated distortion. The pre-painted black enclosure, red control knobs and red LED indicator give the Thunderdrive Deluxe an understated attractive finish. It is capable of overdriving the preamp section of your guitar amp or adding it's own layer of distortion at lower volume.
This is an easy build kit with point to point wiring and clear, easy to follow instructions. The current draw of this pedal is very low at 1.3 milliamps, allowing for long battery life. All you need to provide is solder, soldering iron and a few simple tools.
$39.95
$35.96
You save: 10%
Click to read more
P-H1590DChassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 2.05"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$19.01
$17.11
You save: 10%
Click to read more
P-H550Switch - Carling, Footswitch, DPDT, On-On, Bottom Solder Lugs
Carling, DPDT footswitch, On-On, with solder lugs.

Note: On-On switches may sometimes be referred to as On-None-On.
$10.95
$9.86
You save: 10%
Click to read more
P-H1590BCE-BKChassis Box - 4.39" x 2.34" x 1.06", Black

4.39" x 2.34" x 1.06" D. Equivalent to Hammond P-H1590B, black finish.


$7.95
$7.16
You save: 10%
Click to read more
K-960Effects Pedal Kit - MOD® Kits, The Trill, Tremolo
The Trill tremolo pedal offers classic tremolo tones in an easy to build kit. The Trill's speed knob provides a wide range from a very slow to rapid fire effect. The depth knob varies the ratio between effected and dry signal.
Using modern, low noise transistors makes operation of The Trill quiet with no signal drop when engaged. The Trill uses true bypass foot switching so it is out of the signal path when not engaged.
All you need to provide is solder and tools! Uses 9 volt battery which is not included.
$43.95
$39.56
You save: 10%
Click to read more
K-915Effects Pedal Kit - MOD® Kits, The Verb Deluxe, Digital Reverb
The Verb Deluxe kit is built around the Belton Digi-Log Mini Module (P-RBTDR-2H-X) for a great digital reverb sound. The Belton Digi-Log module was built as a replacement for traditional spring reverberation units.
Features include both Dwell and Mix controls, allowing the dry signal to be blended with the processed signal from a just hint of reverb to deep, cavernous echoes.
The dwell control adds an extra flexibility, providing a full palette of sweet reverb sound.
The effect pedal operates on a 9V battery. For a longer lasting option, a 9-volt adapter can be purchased separately. The Godlyke 9-volt adapter (M-PAS-S) may be purchased separately to power your new pedal.
$79.95
$71.96
You save: 10%
Click to read more
P-H501-PCSwitch - Footswitch, 3PDT, Blue, PC Mount

3PDT latching footswitch with PC terminals. Blue with 9 terminals. Made in Taiwan.


$7.95
$7.16
You save: 10%
Click to read more
R-VWAH-LPPot - 100K, Wah Replacement, Life, Smooth

100K Life Pot is a high grade Wah pot replacement. This wah pedal upgrade is sold with all necessary hardware and gear for immediate installation.


$11.95
$10.76
You save: 10%
Click to read more

Pages

(14 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts