You are here

Effect Pedals & Parts

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
P-ECB-244Battery Box - Dunlop
Original Dunlop snap-in, black battery box with snap-closed swing door for effects pedals using one 9 volt battery (accessed via the bottom of the pedal). Cutout dimensions: 2.46" x 1.27", box depth: 0.70", snaps over a panel thickness of about 0.04". Used on Dunlop Cry Baby Wah Wah GCB95 and many Dunlop effects pedals.
$1.50
Click to read more about this product.
P-H1590BBBKChassis Box - Hammond, Aluminum, 4.67" x 3.68" x 1.1", Black
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Painted with tough polyester powder paint for a lasting finish, even after machining.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$12.98
Click to read more about this product.
P-ECB-152Bottom Plate - Dunlop, for GBC-95 with Battery Door
Bottom Plate with Battery Door for GCB-95. Original Dunlop replacement part.
$11.75
Click to read more about this product.
P-ECB-127Rack - Dunlop, for wahs
Original Dunlop replacement rack for wah pedals (roll pin included: 0.77" length x 0.07" diameter - for mounting the rack to the treadle).
The rack has 14 teeth and mounts to the underside of the treadle piece (rocking structure) of a wah pedal. The teeth of the rack interlock with the teeth of the wah potentiometer gear (i.e. pinion), thereby rotating the potentiometer's shaft as the treadle is rocked back and forth.
$1.95
Click to read more about this product.
R-VPC01Photo Cell - Morley, for Effects Pedals

Photocell for Morley effects pedals. Great replacement for LDR1, LDR2 and LDR3 (M79-211564-000) in Morley Pro Series Volume PVO. Sold individually.


$2.50
Click to read more about this product.
P-ECB-126Gear - Dunlop, for Wah
Original Dunlop replacement gear for wah potentiometers (C-ring included).
The gear has 14 teeth and a flatted inner diameter to fit securely onto a potentiometer with flatted shaft. The included C-ring is placed over the top end of the gear to keep it from sliding off the end of the potentiometer shaft.
$1.95
Click to read more about this product.
P-H1590XXChassis Box - Hammond, Unpainted Aluminum, 5.3" x 4.4" x 1.5"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$14.32
Click to read more about this product.
M-OD9Effects Pedal - Maxon, OD9, Overdrive
Improved circuitry featuring the JRC4558 IC yields the ultra-smooth, creamy, dynamic overdrive so sought after by guitarists.
Overdrive and output level controls adjust the intensity of overdrive and output volume, while the Hi Boost/Hi Cut Tone control adjusts the brightness from warm and smooth to sizzling hot.
While the M-OD808 may have been the first overdrive circuit of its kind, it was the OD-9 that cemented this sound in the history of Rock & Roll guitar. Looking at the OD-9's circuit, you'll realize that this is not some redesign being cleverly marketed as a reissue – this is THE original OD-9 (TS-9) circuit, yet with the addition of true bypass switching.
$159.00
Click to read more about this product.
P-H1590LBChassis Box - Hammond, Unpainted Aluminum, 1.99" x 1.99" x 1.06"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$6.75
Click to read more about this product.
P-ECB-156Inductor - Dunlop, for Crybaby, 500mH
500mH inductor for all Crybaby models. Original Dunlop replacement part.
$11.50
Click to read more about this product.

Pages

(13 pages)
Subscribe to RSS - Effect Pedals & Parts