Pedal Parts / DIY

Replacement for Boss effects pedals, SPST momentary Off-(On), push switch. Mounts in square hole approximately. 55" x.55" x 1.08" overall length including terminals.

Large 5.709” x 3.37” x 1.933” Hammond 1590J enclosures finished in a hammered bronze powdercoat. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Small PCB adapter boards to convert PCB mount 9mm vertical pots to wired panel mount pots. These adapters are great for tight builds allowing for more densely populated panels than 16mm options. They’re also a great way to incorporate sealed potentiometers into builds where larger sized options would be cost prohibitive.

Rubber caps / switch tips for mini toggle switches in a variety of colors. These are made for standard sized toggle bats. Available in 11 different colors.

Good stomp-box effects switch (Triple Pole, Double Throw). 3PDT Latching type footswitch. Made in China.

Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets.

Phenolic PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. The spacing between pads is 7.5mm horizontally and 26mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. See P-HTB-X for black version. See P-HTB-PG-X for premium black version. 2x8 Board:

• 2 rows of 8 eyelets (16 total)
• 7.5mm x 26mm eyelet spacing
• 57.15mm x 30.66mm board
• 45mm spacing for 3.2mm mounting holes
• Great fit for 125B and 1590N1 enclosures

2x12 Board:

• 2 rows of 12 eyelets (24 total)
• 7.5mm x 26mm eyelet spacing
• 87.15mm x 30.66mm board
• 75mm spacing for 3.2mm mounting holes
• Great fit for 1590BB enclosures

Nylon cable tie mounts with adhesive backing. These mounts easily attach to most surfaces using a strong foam adhesive. Zip ties can be fed through the openings on the mount to secure wires to an enclosure, board, or any other convenient location.

Pure Tone has developed a high quality 1/4" three pole (stereo) jack using a new patented design that improves upon and offers a more reliable connection than standard 1/4" jacks. The Pure Tone design features two springs for both the tip connection, a spring for the ring, and an additional spring for the shield connection. These help to secure the plug into place and create a greater surface area connection at contact points to improve stability and signal integrity. These jacks also increase the current capability of 1/4" connections.

Black pointer with white line. Fits a 3/16" knurled shafts. Push on Peavey part: 70902145

Shatterbox style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Shatterbox pedal. The board is styled after the later version with a printed circuit rather than a stripboard construction. This is the same board that was used in the “split board” version which can be built by cutting the board down the middle to separate the fuzz section from the treble booster section. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws.

The BC558 is a silicon general purpose PNP transistor in a TO-92 package. The BC558’s typical applications include signal processing, amplification, and switching.

High quality latching relays from the Panasonic TQ series. These 5 volt relays are commonly used in pedals for true bypass switching. Relay switching can allow for a variety of options on pedal builds. Different footswitch modes can be obtained using the same momentary footswitch. Stereo switching using a standard footswitch is another possible option.
Features:

• Compact low profile size
• Standard DIL spacing for easy PCB use and breadboard compatibility
• Latching
• Single Coil
• 5V Coil Voltage

For a non-latching version, please see P-RP-TQ2-5V.

Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green

ASY76 PNP germanium transistors. The ASY76 is a PNP transistor recommended for audio frequency amplifiers and drivers and works well in effects that use germanium transistors such as fuzz and boost pedals. This transistor is in a TO-5 package with long leads commonly found on germanium transistors.

Anodized aluminum knob with channeled indicator line and set screw. This slim, solid aluminum knob has a diamond knurled grip with a diameter of 0.495”. It also features a counterbore which allows it to hide pot bushings for a clean look. Fits ¼” (6.35mm) pot shafts.

• Height: 0.56 in.
• Diameter: 0.496 in.
• Fits ¼" shaft with set screw

Genuine Cliff barrel plug for use with 5.5mm / 2.1mm barrel jacks. This plug is great for repairing power supplies and making cables. The outside housing is made of a thick durable plastic.

A great digital reverb sound that easily replaces a spring reverberation unit. Stereo outputs may be summed for mono operation. Simple interface requires only input, output, +5V, and ground.

30° sloped aluminum consoles from Hammond’s 1456 Series. These enclosures are a great choice for desktop effects and synthesizers as well as vintage style stompboxes. Features:

• 4" x 5.5" x 3" (1” height at front)
• Bottom panels are 0.081” (2 mm) thick aluminum
• Top panels are 0.064” thick aluminum
• Fully Powder Coated
• Comes with self adhesive rubber feet and required mounting hardware.

Cable for connecting 9V batteries to pedals via their DC input jack. This cable is great for using batteries with pedals that don’t have a battery compartment or for quickly switching from a power supply to a battery. This cable is 3 ¼” inches in length. The barrel plug has a 5.5mm outer diameter and 2.1mm inner diameter. Battery not included.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Durable heavy duty nylon cable ties. These zip ties are a great way to tidy up project wiring and securing components. Features

• Approved for outdoor use.
• UL Listed 6.6 nylon.
• Locks tightly - Won’t stretch or slide.
• Temperature range from 40° to 180°F.
• 8 inch length
• 40 lb tensile strength

High-quality USA made knobs from Rogan Corp. These medium, skirted knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm D-shafts.

• Height: 0.84 in.
• Diameter: 0.62 in.
• Fits 6mm D Shafts
• No indicator

A variety of different sizes are available from the PT Series.