Pedal Parts / DIY

Feet - Bumpers, Tapered Rubber, 3M Adhesive, ½”, Square
Colors Available:
Tapered rubber feet with 3M self-adhesive backing. These square feet have a ½” length and width and can be used to provide grip and slight elevation (0.25") when secured to most project enclosures. Great for effects pedals and rack mount units when removed from the rack. See P-H12R-X for round feet.
$0.69
package of 4
Op-Amp - LF347, Quad, Wide Bandwidth, 14-Pin DIP
LF347 quad op amp in a 14-pin DIP package. The LF347 is a low cost, high speed quad JFET input operational amplifier with an internally trimmed input offset voltage ( BI-FET II™ technology). The device requires a low supply current and yet maintains a large gain bandwidth product and a fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The LF347 is pin compatible with the standard LM348. This feature allows designers to immediately upgrade the overall performance of existing LF348 and LM324 designs. The LF347 may be used in applications such as high speed integrators, fast D/A converters, sample-and-hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth.
$0.69
Feet - Bumpers, Tapered Rubber, 3M Adhesive, ½”, Round
Colors Available:
Tapered rubber feet with 3M self-adhesive backing. These round feet have a ½” diameter and can be used to provide grip and slight elevation (0.15") when secured to most project enclosures. Great for effects pedals and rack mount units when removed from the rack.
Starting at $0.69
package of 4
Op-Amp - TL061, Single, Low Power, JFET-input, 8-Pin DIP
TL061 single op amp in an 8-pin DIP package. The JFET-input operational amplifiers of the TL06x series are designed as low-power versions of the TL08x series amplifiers. They feature high input impedance, wide bandwidth, high slew rate, and low input offset and input bias currents. The TL06x series features the same terminal assignments as the TL07x and TL08x series. Features
  • Very Low Power Consumption
  • Typical Supply Current: 200 µA (Per Amplifier)
  • Wide Common-Mode and Differential Voltage Ranges
  • Low Input Bias and Offset Currents
  • Common-Mode Input Voltage Range Includes VCC+
  • Output Short-Circuit Protection
  • High Input Impedance: JFET-Input Stage
  • Internal Frequency Compensation
  • Latch-Up-Free Operation
  • High Slew Rate: 3.5 V/µs Typical
$0.69
Knob - Pointer, Small, Knurled, 0.675” Diameter
Colors Available:
This vintage knob design has been used on numerous boutique pedals. These classy knurled pointer knobs feature a slotted set screw, and fit ¼" solid shaft potentiometers. These are a close match to the Davies 1400.
  • Height: 0.43 in.
  • Length: 0.825 in.
  • Fits ¼" shaft with set screw
$0.69
CMOS - CD4094, 8-Stage Shift-and-Store Bus Register, 14-Pin DIP
CD4094B is an 8-stage serial shift register having a storage latch associated with each stage for strobing data from the serial input to parallel buffered 3-state outputs. The parallel outputs may be connected directly to common bus lines. Data is shifted on positive clock transitions. The data in each shift register stage is transferred to the storage register when the STROBE input is high. Data in the storage register appears at the outputs whenever the OUTPUT-ENABLE signal is high. Two serial outputs are available for cascading a number of CD4094B devices. Data is available at the QS serial output terminal on positive clock edges to allow for high-speed operation in cascaded systems in which the clock rise time is fast.
$0.69
Op-Amp - NJM4580L, Dual, Audio, 8-Pin SIP
NJM4580L dual op amp from JRC in a SIP8 package. The NJM4580L is the same as the DIP NJM4580 (JRC4580) otherwise. The SIP version is a great replacement for dual op amps in vintage circuits as well as a space saving package for some PCB layouts. The NJM4580 is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, and it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools.
$0.69
Knob - Small, Indicator Line, set screw
Colors Available:
The P-K380 is a high quality Davies 1510 clone. This classic design can be found on countless pedals, synths, amps and other equipment. The set screw uses a metal insert for additional stability and durability. This knob has an infilled painted indicator and fits 1/4" (6.35mm) pot shafts. The P-K380 pairs nicely with the color matched P-K801-BRASS-X knobs.
Starting at $0.70
PCB - LED Driver, for Pedals and Synths
This small PCB is a simple way to add an indicator light that pulses to the rate of LFOs and clocks used in pedals, synthesizers, and other equipment. Simply connect the positive supply voltage to V+, ground to GND, and the output of a positive signal (0 to V+) such as an LFO or clock to the IN pad. The trimmer can adjust how the LED reacts to the signal. Fully clockwise it will simply pulse on and off when paired with a strong signal. If the signal is a sine, triangle, or any other non-pulse type signal, adjusting the trimmer counter clockwise can dial in settings that follow the shape of the waveform, brightening and dimming with the changing voltage. For certain dual op-amp LFOs in effect pedals, the signal may not go low enough to turn the LED fully off.
$0.70
Power Jack - DC Panel Mount, Low Profile, 5.5mm External, 2.1mm Internal
Low profile DC jack with solder lugs. This jack is the perfect size for smaller builds where additional space is necessary. The low profile DC jack is also great for builds where aesthetics are a priority. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Features two solder lugs for tip and ring.
$0.70
Op-Amp - TL072, Dual, Low-Noise, JFET Input, 8-Pin DIP
The TL072 is a high speed JFET input dual operational amplifier incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The device features high slew rates, low input bias and offset current, and low offset voltage temperature coefficient.
$0.70
Transistor - BC183, General Purpose, TO-92 case, NPN
The BC183 is a general purpose NPN transistor in a TO-92 case. The BC183 is commonly used in fuzz pedals and has a reputation as a warm sounding silicon transistor for fuzz.
$0.70
Transistor - 2N7000, Mosfet, Small Signal
2N7000 N-channel enhancement mode field effect transistors. 2N7000 MOSFETs are used in many DIY projects such as boost and distortion effects pedals.
Features:
  • Voltage Controlled Small Signal Switch
  • High Saturation Current Capability
  • Rugged and Reliable
  • High Density Cell Design for Low RDS(ON)
$0.72
Nut & Washer - Panel, for ⅜" Potentiometers
Replacement nut and washer for pots with a ⅜" bushing diameter.
$0.75
CMOS - CD4049, Hex Inverting Buffer and Converter, 16-Pin DIP
The CD4049UB devices are inverting hex buffers, and feature logic-level conversion using only one supply voltage (VCC). The input-signal high level (VIH) can exceed the VCC supply voltage when these devices are used for logic level conversions. These devices are intended for use as CMOS to DTL or TTL converters and can drive directly two DTL or TTL loads. (VCC = 5 V, VOL ≤ 0.4 V, and IOL ≥ 3.3 mA.) Features:
  • Inverting
  • High Sink Current for Driving 2 TTL Loads
  • High-to-Low Level Logic Conversion
  • 100% Tested for Quiescent Current at 20 V
  • Maximum Input Current of 1 µA at 18 V Over Full
  • Package Temperature Range; 100 nA at 18 V and 25°C
  • 5-V, 10-V, and 15-V Parametric Ratings

Applications
  • CMOS to DTL or TTL Hex Converters
  • CMOS Current Sink or Source Drivers
  • CMOS High-to-Low Logic Level Converters
$0.75
CMOS - CD4007, Dual Complementary Pair Plus Inverter, 14-Pin DIP
CD4007UB types are comprised of three n-channel and three p-channel enhancement-type MOS transistors. The transistor elements are accessible through the package terminals to provide a convenient means for constructing the various typical circuits as shown in Fig. 2. More complex functions are possible using multiple packages. Numbers shown in parentheses indicate terminals that are connected together to form the various configurations listed. Features:
  • Standardized symmetrical output characteristics
  • Medium Speed Operation — tPHL, tPLH = 30 ns (typ.) at 10 V
  • 100% tested for quiescent current at 20 V
  • Meets all requirements of JEDEC Tentative Standard No.
$0.75
Knob - Brass Insert, Set Screw, Fits ¼” Shafts
Brass inserts for knobs. Fits ¼” potentiometer shafts. Features a slotted set screw. These inserts are a great option for repairing knobs with stripped out set screws or for building DIY knobs using resin molds, 3D printing, or any other method.
$0.75
CMOS - CD4029, Presettable Up/Down Counter, 16-Pin DIP
CD4029B consists of a four-stage binary or BCD-decade up/down counter with provisions for look-ahead carry in both counting modes. The inputs consist of a single CLOCK, CARRY-IN\ (CLOCK ENABLE\), BINARY/DECADE, UP/DOWN, PRESET ENABLE, and four individual JAN signals, Q1, Q2, Q3, Q4 and a CARRY OUT\ signal are provided as outputs. A high PRESET ENABLE signal allows information on the JAM INPUTS to preset the counter to any state asynchronously with the clock. A low on each JAM line, when the PRESET-ENABLE signal is high, resets the counter to its zero count. The counter is advanced one count at the positive transition of the clock when the CARRY-IN\ and PRESET ENABLE signals are low. Advancement is inhibited when the CARRY-IN\ or PRESET ENABLE signals are high. The CARRY-OUT\ signal is normally high and goes low when the counter reaches its maximum count in the UP mode or the minimum count in the DOWN mode provided the CARRY-IN\ signal is low.
$0.75
CMOS - CD4093, Quad 2-Input NAND Schmitt Triggers, 14-Pin DIP
CD4093B consists of four Schmitt-trigger circuits. Each circuit functions as a two-input NAND gate with Schmitt-trigger action on both inputs. The gate switches at different points for positive- and negative-going signals. The difference between the positive voltage (VP) and the negative voltage (VN) is defined as hysteresis voltage (VH). Features:
  • Schmitt-trigger action on each input with no external components
  • Hysteresis voltage typically 0.9 V at VDD = 5 V and 2.3 V at VDD = 10 V
  • Noise immunity greater than 50%
  • No limit on input rise and fall times
  • Standardized, symmetrical output characteristics
  • 100% tested for quiescent current at 20 V
  • Maximum input current of 1 µA at 18 V over full package-temperature range, 100 nA at 18 V and 25°C
  • 5-V, 10-V, and 15-V parametric ratings
  • Meets all requirements of JEDEC Tentative Standard No.
$0.75
CMOS - CD4013, Dual D-Type Flip-Flop, 14-Pin DIP
The CD4013B device consists of two identical, independent data-type flip-flops. Each flip-flop has independent data, set, reset, and clock inputs and Q and Q outputs. These devices can be used for shift register applications, and, by connecting Q output to the data input, for counter and toggle applications. The logic level present at the D input is transferred to the Q output during the positive-going transition of the clock pulse.
$0.75
CMOS - CD4053, 2:1 SPDT, 3-Channel Analog Multiplexer with Logic-Level Conversion, 16-Pin DIP
The CD4053B analog multiplexers are digitally-controlled analog switches having low ON impedance and very low OFF leakage current.
$0.75
CMOS - CD40106, Hex Schmitt-Trigger Inverters, 14-Pin DIP
The CD40106B device consists of six Schmitt-Trigger inputs. Each circuit functions as an inverter with Schmitt-Trigger input. The trigger switches at different points for positive- and negative-going signals. The difference between the positive-going voltage (VP) and the negative-going voltages (VN) is defined as hysteresis voltage (VH). Features:
  • Schmitt-Trigger Inputs
  • Hysteresis Voltage (Typical):
    • 0.9 V at VDD = 5 V
    • 2.3 V at VDD = 10 V
    • 3.5 V at VDD = 15 V
  • Noise Immunity Greater Than 50%
  • No Limit On Input Rise and Fall Times
  • Standardized, Symmetrical Output Characteristics
  • For Quiescent Current at 20 V
  • Maximum Input Current Of 1 µA at 18 V Over Full Package Temperature Range: 100 nA at 18 V and 25°C
  • Low VDD and VSS Current During Slow Input Ramp
  • 5-V, 10-V, and 15-V Parametric Ratings
$0.75
Cloth Pedal Bag - 4” x 6”, 100% Cotton
Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 4 in. x 6 in. and fit 1590B or smaller stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.
$0.75
LED - 5mm diameter, diffused lens, 5 mCd
Colors Available:
5mm (T-1 ¾) diffused LED’s. Great for use in pedal builds and other applications where a tinted and diffused indicator is needed. Multiple colors available.
  • 5mm size
  • Tinted and diffused
  • Multiple colors available
  • Package of 5
$0.75
package of 5