Pedal Parts / DIY

CD4001UB quad 2-input NOR gate provides the system designer with direct implementation of the NOR function and supplements the existing family of CMOS gates. Features:

• Propagation delay time = 30 ns (typ.) at CL = 50 pF, VDD = 10 V
• Standardized symmetrical output characteristics
• 100% tested for maximum quiescent current at 20 V
• Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of ’B’ Series CMOS Devices"
• Maximum input current of 1 µA at 18 V over full package-temperature range; 100 nA at 18 V and 25°C
• 5-V, 10-V, and 15-V parametric ratings

The CD4050B devices are noninverting hex buffers, and feature logic-level conversion using only one supply voltage (VCC). The input-signal high level (VIH) can exceed the VCC supply voltage when these devices are used for logic level conversions. These devices are intended for use as CMOS to DTL or TTL converters and can drive directly two DTL or TTL loads. (VCC = 5 V, VOL ≤ 0.4 V, and IOL ≥ 3.3 mA.) Features:

• Noninverting
• High Sink Current for Driving 2 TTL Loads
• High-to-Low Level Logic Conversion
• 100% Tested for Quiescent Current at 20 V
• Maximum Input Current of 1 µA at 18 V Over Full
• Package Temperature Range; 100 nA at 18 V and 25°C
• 5-V, 10-V, and 15-V Parametric Ratings

Applications

• CMOS to DTL or TTL Hex Converters
• CMOS Current Sink or Source Drivers
• CMOS High-to-Low Logic Level Converters

Generic rack with 18 teeth for wah and other pedals using rack and pinion potentiometer shaft rotation. (Length = 1.91", width = 0.19", height = 0.25". Mounting hole diameter = 0.075")

CD4011B NAND gates provide the system designer with direct implementation of the NAND function and supplement the existing family of CMOS gates. All inputs and outputs are buffered. Features:

• Propagation delay time = 60 ns (typ.) at CL = 50 pF, VDD = 10 V
• Buffered inputs and outputs
• Standardized symmetrical output characteristics
• Maximum input current of 1 µA at 18 V over-full package temperature range; 100 nA at 18 V and 25°C
• 100% tested for quiescent current at 20 V
• 5-V, 10-V, and 15-V parametric ratings
• Noise margin (over full package temperature range:
  
  • 1 V at VDD = 5 V
  • 2 V at VDD = 10 V
  • 2.5 at VDD = 15 V
• Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of "B" Series CMOS Devices"

CD4015B consists of two identical, independent, 4-stage serial-input/parallel-output registers. Each register has independent CLOCK and RESET inputs as well as a single serial DATA input. "Q" outputs are available from each of the four stages on both registers. All register stages are D-type, master-slave flip-flops. The logic level present at the DATA input is transferred into the first register stage and shifted over one stage at each positive-going clock transition. Resetting of all stages is accomplished by a high level on the reset line.

Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 4 in. x 6 in. and fit 1590B or smaller stompboxes. Cloth pedal bags are also great packaging for boutique pedal builders.

The CD4049UB devices are inverting hex buffers, and feature logic-level conversion using only one supply voltage (VCC). The input-signal high level (VIH) can exceed the VCC supply voltage when these devices are used for logic level conversions. These devices are intended for use as CMOS to DTL or TTL converters and can drive directly two DTL or TTL loads. (VCC = 5 V, VOL ≤ 0.4 V, and IOL ≥ 3.3 mA.) Features:

• Inverting
• High Sink Current for Driving 2 TTL Loads
• High-to-Low Level Logic Conversion
• 100% Tested for Quiescent Current at 20 V
• Maximum Input Current of 1 µA at 18 V Over Full
• Package Temperature Range; 100 nA at 18 V and 25°C
• 5-V, 10-V, and 15-V Parametric Ratings

Applications

• CMOS to DTL or TTL Hex Converters
• CMOS Current Sink or Source Drivers
• CMOS High-to-Low Logic Level Converters

Large rubber grommet for mounting footswitches on FZ-1 and FZ-1A style builds. Requires a 0.812” (20.6mm) mounting hole. This grommet’s 0.5” (12.7mm) inner diameter fits most common footswitches. These are great for replacing originals, replica builds of these Maestro pedals or for general sound damping on footswitches.

PCB mount terminal pin made of tinned brass. This pin fits 0.064” mounting holes and can be swage or solder mounted. The pin diameter is 0.05” and has a total length of 0.25” when mounted. Great for connecting offboard wiring by soldering directly to the pin or using an appropriate connector.

Set screw knob with indicator line and scalloped edge. Measures .50" in diameter and .6" in height. Davies 1900H clone

Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.

The 2N2484 is a silicon planar epitaxial NPN transistor in a TO-18 metal case type. The 2N2484 is primarily intended for use in high performance, low level, low noise amplifier applications.

Eyelets, bag of 10 (mounts in 1/8" hole).

Three conductor Flexstrip ribbons cables. These ribbons feature a nomex insulator so there are no melting issues when soldering. Unlike typical ribbon cables, the wires are designed to distribute the stress of the bend and vibrations throughout the entire cable rather than directly on the solder joints. These cables are a great choice for PCB to PCB connections in pedals, synths, and other electronics. The spacing is .1" (2.54mm).

Four conductor Flexstrip ribbons cables. These ribbons feature a nomex insulator so there are no melting issues when soldering. Unlike typical ribbon cables, the wires are designed to distribute the stress of the bend and vibrations throughout the entire cable rather than directly on the solder joints. These cables are a great choice for PCB to PCB connections in pedals, synths, and other electronics. The spacing is .1" (2.54mm).

TL071 single op amp in an 8-pin DIP package. The TL07xx JFET-input operational amplifier family is designed to offer a wider selection than any previously developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient. The low harmonic distortion and low noise make the TL07xseries ideally suited for high-fidelity and audio pre-amplifier applications.

Small plastic control knob with set screw and metal insert. This knob has a pinched grip similar to the Davies 1510 but features a smaller diameter and scooped cutout for a distinctive appearance. Fits ¼” (6.35mm) pot shafts.

Keep your pedals pristine with these 100% cotton bags. These drawstring bags are 5 in. x 8 in. and fit stompbox sizes up to 1590BB. Cloth pedal bags are also great packaging for boutique pedal builders.

Plastic chicken head knobs for coarse knurled shafts. These tiny chicken head knobs are great for pedal builds or cramped face plates. They feature an inlay indicator line. The total length of the chicken head is 0.93 inches. Fits T18 knurled shafts.

Replacement seal for S-H910 and S-H911 Cliff UK jacks.

Reverse audio taper Alpha 16mm pots with a solid shaft and right angle PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
• Lead Distance from shaft center: 16 mm (0.630”)
• Lead Thickness: 0.5 mm (0.020”)
• Shaft Diameter: 6.35 mm (0.25”)

Audio taper Alpha 16mm pots with a solid shaft and long PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 20.7 mm + 4 mm (0.815” + 0.158”)
• Lead Distance from shaft center: 14.3 mm (0.563”)
• Lead Thickness: 0.5 mm (0.020”)
• Shaft Diameter: 6.35 mm (0.25”)

Panel mount LED lenses made of high quality polycarbonate. These lenses provide a clean semi-flush appearance with a small panel footprint and work well in any project using LED indicators. Features:

• 0.171” mounting hole
• For panel thicknesses of 0.031” to 0.125″
• Fresnel lens
• Low Profile
• Fits standard 3mm LEDs

For a version that fits 5mm LEDs, see P-L710-X.

5kΩ reverse audio taper Alpha 16mm pots with a solid shaft and long PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 20.7 mm + 4 mm (0.815” + 0.158”)
• Lead Distance from shaft center: 14.3 mm (0.563”)
• Lead Thickness: 0.5 mm (0.020”)
• Shaft Diameter: 6.35 mm (0.25”)