You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
K-950Effects Pedal Kit - MOD® Kits, The Thunderdrive, Overdrive

The Thunderdrive is an overdrive pedal kit that will provide a signal boost at low gain settings and its own distortion at maximum gain settings. You can use it to push your preamp into overdrive or as a source of smooth distortion. Adjusting volume control and gain control results in a wide variety of tones in spite of its simple construction. This pedal is capable of overdriving the preamp section of your guitar amp or adding its own layer of distortion at lower volume. Using point to point wiring and easy to follow instructions you can have a working overdrive pedal in a matter of hours. All you need to provide is solder and a soldering iron. Uses 9 volt battery which is not included.


$29.95
$26.66
You save: 11%
Click to read more
P-H503-PCSwitch - Footswitch, DPDT, Momentary, PC Terminals

DPDT momentary footswitch with PC terminals. Black with 6 terminals. AC125V 4A, AC250V 2A.


$4.50
$4.01
You save: 11%
Click to read more
P-ECB-127Rack - Dunlop, replacement for wahs

Original Dunlop replacement rack for wah pedals (roll pin included: 0.77" length x 0.07" diameter - for mounting the rack to the treadle). The rack has 14 teeth and mounts to the underside of the treadle piece (rocking structure) of a wah pedal. The teeth of the rack interlock with the teeth of the wah potentiometer gear (i.e. pinion), thereby rotating the potentiometer's shaft as the treadle is rocked back and forth.


$1.95
$1.74
You save: 11%
Click to read more
P-ECB-126Gear - Dunlop, replacement for Wah

Original Dunlop replacement gear for wah potentiometers (C-ring included). The gear has 14 teeth and a flatted inner diameter to fit securely onto a potentiometer with flatted shaft. The included C-ring is placed over the top end of the gear to keep it from sliding off the end of the potentiometer shaft.


$1.95
$1.74
You save: 11%
Click to read more
P-H1590XChassis Box - Hammond, Unpainted Aluminum, 5.3" x 4.4" x 2.2"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.

$14.34
$12.76
You save: 11%
Click to read more
P-ECB-152Bottom Plate - Dunlop, for GCB-95 with Battery Door

Bottom Plate for GCB-95. Original Dunlop replacement part. Includes battery box, four mounting screws and four black rubber feet.


$13.95
$12.42
You save: 11%
Click to read more
P-H1590EChassis Box - Hammond, Unpainted Aluminum, 7.38" x 4.70" x 3.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$21.69
$19.30
You save: 11%
Click to read more
R-VPC01Photo Cell - Morley, for Effects Pedals

Photocell for Morley effects pedals. Great replacement for LDR1, LDR2 and LDR3 (M79-211564-000) in Morley Pro Series Volume PVO. Sold individually.


$2.50
$2.23
You save: 11%
Click to read more
P-ECB-24CPotentiometer - Dunlop, 20 kΩ, Custom Taper, Wah Pot, for Bass

Custom taper 20k Dunlop potentiometer used in 105Q Crybaby Bass Wah. 1 million cycles, maintenance free.


$22.95
$20.43
You save: 11%
Click to read more
P-H1590FChassis Box - Hammond, Unpainted Aluminum, 7.38" x 7.38" x 2.48"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.
$27.31
$24.31
You save: 11%
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts