Pedal Parts / DIY
Transistor - 2N708, Silicon, TO-18 case, NPN
The 2N708 is a silicon NPN transistor in a TO-18 metal case type. The 2N708 is primarily intended for use in high speed switching and VHF amplification applications.
$0.75
Rack - gear, for wahs and other pedals
Generic rack with 18 teeth for wah and other pedals using rack and pinion potentiometer shaft rotation. (Length = 1.91", width = 0.19", height = 0.25". Mounting hole diameter = 0.075")
$0.75
CMOS - CD4001, Quad 2-Input NOR Gate, 14-Pin DIP
CD4001UB quad 2-input NOR gate provides the system designer with direct implementation of the NOR function and supplements the existing family of CMOS gates. Features:
- Propagation delay time = 30 ns (typ.) at CL = 50 pF, VDD = 10 V
- Standardized symmetrical output characteristics
- 100% tested for maximum quiescent current at 20 V
- Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of ’B’ Series CMOS Devices"
- Maximum input current of 1 µA at 18 V over full package-temperature range; 100 nA at 18 V and 25°C
- 5-V, 10-V, and 15-V parametric ratings
$0.75
CMOS - CD4050, Hex Inverting Buffer and Converter, 16-Pin DIP
The CD4050B devices are noninverting hex buffers, and feature logic-level conversion using only one supply voltage (VCC). The input-signal high level (VIH) can exceed the VCC supply voltage when these devices are used for logic level conversions. These devices are intended for use as CMOS to DTL or TTL converters and can drive directly two DTL or TTL loads. (VCC = 5 V, VOL ≤ 0.4 V, and IOL ≥ 3.3 mA.) Features:
Applications
- Noninverting
- High Sink Current for Driving 2 TTL Loads
- High-to-Low Level Logic Conversion
- 100% Tested for Quiescent Current at 20 V
- Maximum Input Current of 1 µA at 18 V Over Full
- Package Temperature Range; 100 nA at 18 V and 25°C
- 5-V, 10-V, and 15-V Parametric Ratings
Applications
- CMOS to DTL or TTL Hex Converters
- CMOS Current Sink or Source Drivers
- CMOS High-to-Low Logic Level Converters
$0.75
Nut - Dress Nut, For Mini Toggle Switches
Dress nuts for use with mini toggle switches. These plated dress nuts feature a chamfered edge for a professional look and work on any 1/4-40 UNS threaded bushing. Two sides are flatted for use with a tool when fastening.
Colors Available:
Starting at $0.75
CMOS - CD4011, 2-Input CMOS NAND Gates, 14-Pin DIP
CD4011B NAND gates provide the system designer with direct implementation of the NAND function and supplement the existing family of CMOS gates. All inputs and outputs are buffered. Features:
- Propagation delay time = 60 ns (typ.) at CL = 50 pF, VDD = 10 V
- Buffered inputs and outputs
- Standardized symmetrical output characteristics
- Maximum input current of 1 µA at 18 V over-full package temperature range; 100 nA at 18 V and 25°C
- 100% tested for quiescent current at 20 V
- 5-V, 10-V, and 15-V parametric ratings
- Noise margin (over full package temperature range:
- 1 V at VDD = 5 V
- 2 V at VDD = 10 V
- 2.5 at VDD = 15 V
- Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of "B" Series CMOS Devices"
$0.75
Regulator - LM317T, Adjustable Output, 1.5A, Linear Voltage Regulator
Linear regulator with an adjustable voltage range from 1.2V to 37V. This regulator can supply 1.5A of current making it a great option for power supplies.
$0.75
CMOS - CD4015, Dual 4-Stage Static Shift Register, 16-Pin DIP
CD4015B consists of two identical, independent, 4-stage serial-input/parallel-output registers. Each register has independent CLOCK and RESET inputs as well as a single serial DATA input. "Q" outputs are available from each of the four stages on both registers. All register stages are D-type, master-slave flip-flops. The logic level present at the DATA input is transferred into the first register stage and shifted over one stage at each positive-going clock transition. Resetting of all stages is accomplished by a high level on the reset line.
$0.75
Knob - Mini Indicator, Set Screw, 15mm x 11mm
Mini fluted knob with infilled indicator line. Pairs well with the larger P-K850X. Fits ¼” (6.35mm) pot shafts.
Colors Available:
- Height: 11mm
- Diameter: 15mm
- Fits 1/4" shaft with set screw
Starting at $0.75
Grommet - Rubber, for FZ-1 Style Footswitch Mounting
Large rubber grommet for mounting footswitches on FZ-1 and FZ-1A style builds. Requires a 0.812” (20.6mm) mounting hole. This grommet’s 0.5” (12.7mm) inner diameter fits most common footswitches. These are great for replacing originals, replica builds of these Maestro pedals or for general sound damping on footswitches.
$0.79
Terminal Pin - PCB Mount, 0.05” Diameter, 0.25” Length
PCB mount terminal pin made of tinned brass. This pin fits 0.064” mounting holes and can be swage or solder mounted. The pin diameter is 0.05” and has a total length of 0.25” when mounted. Great for connecting offboard wiring by soldering directly to the pin or using an appropriate connector.
$0.79
Ribbon Cable - Flexstrip, 3 Conductor
Three conductor Flexstrip ribbons cables. These ribbons feature a nomex insulator so there are no melting issues when soldering. Unlike typical ribbon cables, the wires are designed to distribute the stress of the bend and vibrations throughout the entire cable rather than directly on the solder joints. These cables are a great choice for PCB to PCB connections in pedals, synths, and other electronics. The spacing is .1" (2.54mm).
Starting at $0.80
Eyelets - Brass, .121 x .125 x .200; MT .0095, package of 10
Eyelets, bag of 10 (mounts in 1/8" hole).
$0.80
package of 10
Op-Amp - LF353, Dual, Wide-Bandwidth, JFET Input, 8-Pin DIP
Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.
$0.80
Transistor - 2N2484, Silicon, TO-18 case, NPN
The 2N2484 is a silicon planar epitaxial NPN transistor in a TO-18 metal case type. The 2N2484 is primarily intended for use in high performance, low level, low noise amplifier applications.
$0.80
Ribbon Cable - Flexstrip, 4 Conductor
Four conductor Flexstrip ribbons cables. These ribbons feature a nomex insulator so there are no melting issues when soldering. Unlike typical ribbon cables, the wires are designed to distribute the stress of the bend and vibrations throughout the entire cable rather than directly on the solder joints. These cables are a great choice for PCB to PCB connections in pedals, synths, and other electronics. The spacing is .1" (2.54mm).
Starting at $0.81
Op-Amp - TL071, Single, Low-Noise, JFET-input, 8-Pin DIP
TL071 single op amp in an 8-pin DIP package. The TL07xx JFET-input operational amplifier family is designed to offer a wider selection than any previously developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient. The low harmonic distortion and low noise make the TL07xseries ideally suited for high-fidelity and audio pre-amplifier applications.
$0.82
Knob - Plastic, Set Screw, Small MXR Style, 0.75" diameter
Small plastic knobs with set screw and brass insert. Similar to the small knobs used on many Dunlop / MXR pedals. These knobs have a fluted grip with an indicator line as well as a dot indicator on the skirt. Fits ¼” (6.35mm) pot shafts.
Colors Available:
Starting at $0.85
Knob - Plastic, Set Screw, Fluted w/ Line, 0.745" Diameter
Plastic control knob with set screw and brass insert. This knob features a distinctive fluting similar to the popular Philmore 3010 knob. This style is also similar to the small skirted MXR knobs. Fits ¼” (6.35mm) pot shafts.
Colors Available:
$0.85
LED Lens - Flat Cylindrical, Fresnel, Polycarbonate, 3mm
Panel mount LED lenses made of high quality polycarbonate. These flat cylindrical lenses provide a unique retro appearance with a small panel footprint and work well in any project using LED indicators. Features:
Colors Available:
- 0.171” mounting hole
- For panel thicknesses of 0.031” to 0.094″
- Fresnel lens
- Flat cylindrical shape
- Fits standard 3mm LEDs
$0.85
Potentiometer - Alpha, Linear, Solid Shaft, Right Angle, 16mm
Alpha Mini Pots with solid shaft and long PC mount terminals.
- Threading: M7 x 0.75
- Distance between terminals: 5 mm (0.197”)
- Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
- Lead Distance from shaft center: 16 mm (0.630”)
- Lead Thickness: 0.5 mm (0.020”)
Starting at $0.85
Cable Tie - durable Nylon, 5.5”, 18 lb
Durable nylon cable ties. These zip ties are a great way to tidy up project wiring and securing components. Features
Colors Available:
- Approved for outdoor use.
- UL Listed 6.6 nylon.
- Locks tightly - Won’t stretch or slide.
- Temperature range from 40° to 180°F.
Starting at $0.85
package of 10
Dust Cover - Rubber covering for Potentiometers, black
Black dust cover for use with 16mm or 24mm potentiometers. These covers slide over the back of the pot covering the holes and gaps to help prevent dust from accumulating inside avoiding potential repairs and replacing down the road. The dust cover is made of a soft rubbery material and is easy to install on standard 24mm and 16mm pots.
Starting at $0.85
Potentiometer - Alpha, W-Taper, Solid Shaft, Right Angle, 16mm, 20kΩ
20kΩ W taper Alpha 16mm pots with a solid shaft and right angle PC mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.
- Threading: M7 x 0.75
- Distance between terminals: 5 mm (0.197”)
- Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
- Lead Distance from shaft center: 16 mm (0.630”)
- Lead Thickness: 0.5 mm (0.020”)
- Shaft Diameter: 6.35 mm (0.25”)
$0.85