You are here

Effect Pedals & Parts

Adding effects to your signal path is a great way to alter the sound of your guitar. Add reverb, delay, distortion, frequency ranges and other dynamic effects.

Build a kit or purchase parts to make your own!

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(13 pages)
P-ECB-24DPotentiometer - Dunlop, 250 kΩ Audio, for Dunlop GCB80

250 kΩ gear shaft pot with an audio taper. Original Dunlop replacement part. Used in the Dunlop GCB80 High Gain Volume Pedal.


$19.95
Click to read more
P-ECB-24BPotentiometer - Dunlop, Hot Potz II Crybaby, 100 kΩ

Hot Potz II Crybaby Pot. for newer Crybaby models. Made by Beckman. 100 kΩ. Original Dunlop replacement part. The same tone and sweep characteristics as the original Cry Baby Hot Potz potentiometer with low wiper noise and extended life.


$20.59
Click to read more
P-H1590EChassis Box - Hammond, Diecast Aluminum, 7.38" x 4.70" x 3.07"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.

$21.69
Click to read more
P-H-LEHLE-SW-XRelay Module - Lehle, Relay True Bypass Switching Unit

The LEHLE MODULE SW is a true bypass switching unit with relay and an active pop suppression function controlled by an intelligent microcontroller circuit, thereby allowing the LEHLE MODULE SW to switch even faster than mechanical switches, noise-free and without wear.


Starting at $21.89
Click to read more
P-ECB-24APotentiometer - Dunlop Hot Potz, 470 kΩ

Used in Jimi Hendrix's WAH and Dunlop volume pedal. 470 kΩ. Original Dunlop replacement part.


$22.95
Click to read more
P-ECB-24CPotentiometer - Dunlop, 20 kΩ, Custom Taper, Wah Pot, for Bass

Custom taper 20k Dunlop potentiometer used in 105Q Crybaby Bass Wah. 1 million cycles, maintenance free.


$22.95
Click to read more
P-ECB-25PC Board - Dunlop, for Crybaby

Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.


$22.95
Click to read more
P-H1590VChassis Box - Hammond, Unpainted Aluminum, 4.70" x 4.70" x 3.54"

Special Order Item

  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Four 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C.
$23.15
Note: special order items require additional lead time. See our page on special order items.
Note: this is a special order item.
Click to read more
M-PAS-XPower Supply - Power All System, For Effects Pedals

The Power-All PA-9 Digital Power Supply is the world’s first 2,000 mA, single outlet power supply designed specifically for guitar effect users. Don’t waste money on batteries or take up valuable space with multiple “wall wart” adaptors or power bricks – the Power-All system can power your entire pedalboard from a single power supply that takes up only one outlet! The Power-All provides 9 volts DC at 2,000 milliamps – more than enough current to power dozens of effect pedals, including up to four Line 6 Modelers! The Power-All’s special circuit design offers the lowest noise floor of any digital power supply on the market. The PA-9 now comes with a ferrite-core filter built onto its output cable to further reduce noise and hum.


Starting at $24.95
Click to read more
P-H1590FChassis Box - Hammond, Diecast Aluminum, 7.38" x 7.38" x 2.48"
  • Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
  • Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
  • Vibra finished for a smooth surface with no sharp edges.
  • Six 6-32 x ½" machine screws secure lid - into tapped holes.
  • Designed to meet IP54.
  • Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
  • Dimensions shown are exterior dimensions.

$27.31
Click to read more

Pages

(13 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Effect Pedals & Parts