Pedal Parts / DIY

Transistor - 2SD77, Germanium, TO-1 case, NPN
2SD77 NPN germanium transistors. The 2SD77 is a popular NPN for fuzz pedals and other effects. The NPN polarity allows for use with standard pedal power supplies.
$1.65
Power Jack - Cliff, DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
High quality ½" panel mount DC jack with solder lugs from Cliff Electronic Components. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch. Mounting nut included.
$1.35
Footswitch - 4PDT, Black, Solder Lugs
Quad Pole, Double Throw (4PDT), latching footswitch with 12 solder lugs.
$4.99
Gear - Dunlop, replacement for Wah D-shaft pots
Original Dunlop replacement gear for wah potentiometers (C-ring included). The gear has 14 teeth and a flatted inner diameter to fit securely onto a potentiometer with flatted shaft. The included C-ring is placed over the top end of the gear to keep it from sliding off the end of the potentiometer shaft.
$4.95
Ribbon Cable - Flexstrip, 8 Conductor
Eight conductor Flexstrip ribbons cables. These ribbons feature a nomex insulator so there are no melting issues when soldering. Unlike typical ribbon cables, the wires are designed to distribute the stress of the bend and vibrations throughout the entire cable rather than directly on the solder joints. These cables are a great choice for PCB to PCB connections in pedals, synths, and other electronics. The spacing is .1" (2.54mm).
Starting at $1.20
Audio Power Amplifier - LM380, Class-AB, 2.5W, 14-Pin DIP
LM380 power amp in a 14-pin DIP package. The LM380 is a power audio amplifier for consumer applications. In order to hold system cost to a minimum, gain is internally fixed at 34 dB. A unique input stage allows ground referenced input signals. The output automatically self-centers to one-half the supply voltage. The output is short circuit proof with internal thermal limiting. The package outline is standard dual-in-line. The LM380N uses a copper lead frame. The center three pins on either side comprise a heat sink.
$1.95
Op-Amp - TL062, Dual, Low-Power, JFET Input, 8-Pin DIP
Dual low power opamps in an 8-pin DIP package. The TL062 offers a high input impedance and 1MHz bandwidth.
$0.95
Diode - standard recovery rectifier, 3A, 1000V, 1N5408
1N5408 Diode. Lead mounted standard recovery rectifiers are designed for use in power supplies and other applications having need of a device with the following features:
  • High Current to Small Size
  • High Surge Current Capability
  • Low Forward Voltage Drop
$0.43
CMOS - CD4011, 2-Input CMOS NAND Gates, 14-Pin DIP
CD4011B NAND gates provide the system designer with direct implementation of the NAND function and supplement the existing family of CMOS gates. All inputs and outputs are buffered. Features:
  • Propagation delay time = 60 ns (typ.) at CL = 50 pF, VDD = 10 V
  • Buffered inputs and outputs
  • Standardized symmetrical output characteristics
  • Maximum input current of 1 µA at 18 V over-full package temperature range; 100 nA at 18 V and 25°C
  • 100% tested for quiescent current at 20 V
  • 5-V, 10-V, and 15-V parametric ratings
  • Noise margin (over full package temperature range:
    • 1 V at VDD = 5 V
    • 2 V at VDD = 10 V
    • 2.5 at VDD = 15 V
  • Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of "B" Series CMOS Devices"
$0.75
Knob - Davies, 1600 & 1610, Daka-ware, Skirted
High-quality USA made knobs from Davies Molding. The small skirted 1610 knob is made of solid phenolic and features an indicator line on the 0.91” diameter skirt. This classic knob has been used on a variety of equipment and most notably on the Buchla 100 Series as well as some 200 Series modules.
  • Height: 0.59 in.
  • Diameter: 0.91 in.
  • Fits ¼" shaft with set screw

The large skirted 1600 knob is made of phenolic and features an indicator line on the 1.5” diameter skirt. This classic knob has been used on a variety of equipment and most notably on the Buchla 100 Series as well as some 200 Series modules.
  • Height: 0.69 in.
  • Diameter: 1.5 in.
  • Fits ¼" shaft with set screw
$3.09
Knob - Aluminum, Set Screw, Skirted w/ Line, 1.125" Diameter
Colors Available:
Large skirted aluminum knob with indicator line and set screw. This solid aluminum knob has a 1.125 in. diameter skirt and ¾” grip that features a minimalistic style of fluting. The knob uses dual set screws to ensure no slipping once set on the pot’s shaft. Fits ¼” (6.35mm) pot shafts.
$4.75
Wire - 22 AWG Stranded Core, PVC, 600V, 50 Foot Roll
Colors Available:
600V stranded. Strands are tinned individually. See photos for detail. UL style 1015, rated to 105 degrees C. Perfect for new projects or rewiring any electrical equipment.
Starting at $7.95
Standoff - M3 Threaded, Adhesive Backing
Adhesive backed standoff with M3 threading. The high-strength adhesive tape allows the standoff to be securely mounted, providing an easy option for mounting PCBs in enclosures. These standoffs use a captive metal nut in a strong nylon plastic base for a durable and lightweight solution.
$0.95
Transistor - 2N5135, Silicon, TO-105 case, NPN
The 2N5135 is a silicon NPN transistor in a TO-105 case. This transistor is a close match to the rare 2N5133 but with higher voltage ratings and is in a larger package. The hFE range is less wide than the 2N5133 with more values in the range found in the batches used on vintage Big Muff pedals. The lower hFE range also makes these a great option for silicon fuzz pedals.
$1.75
Power Jack - Lumberg, DC Panel Mount, 5.5mm External, 2.1mm Internal
Lumberg panel mount barrel jack with solder lugs.This DC jack features a normally closed switch on the ring (sleeve) connection. For use with barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Mounting nut included.
$1.35
Battery Box - Gotoh, BB-04W, Dual, for 9 volt batteries
Dual 9 volt battery box. Two 9V battery compartments, each compartment having its own red and black wires for battery positive and negative connections (4 wires total) allowing for series, parallel or separate connections of two 9V batteries. Four wood screws included. Directions: 1. Refer to the Drawing B and make a hole on guitar body. 57.5 mm (2.26") x 49.5 mm (1.95"), R6 (6 mm = 0.24") 2. Put the box in guitar body and fix it by screws.
$19.95
Knob - Aluminum, Matte Finish, Set Screw, Short Line, 0.75" Diameter
Colors Available:
Anodized aluminum knob with short indicator line, set screw, and a matte metal finish. This solid aluminum knob has a straight knurled grip with a diameter of 0.75”. The knob also features a counterbore which allows it to hide pot bushings for a clean look. Fits ¼” (6.35mm) pot shafts. For a smaller version of this knob, see P-K656-X. For a brushed finish version of this knob, see P-K310X.
$2.25
PadBoard - Single Sided, 3.04” x 1.55”, Vintage Spacing
Colors Available:
Padboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid of pads and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each square pad is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm FR4 glass-epoxy circuit board
  • 1oz/ft2 copper weight
  • HASL coated square shaped pads
  • 20 x 10 holes
  • 3.04” x 1.55”
$2.99
Resistors - ¼ Watt, Metal Film, 1% tolerance
Metal Film resistors consist of a resistive element of an extremely thin layer of metal alloy vacuum deposited on a substrate. Precise and quiet. Package of 5. These resistors are perfect for pedal builders! 1/4 watt.
Starting at $0.45
package of 5
Footswitch - Carling, SPST, for Fender® Switching Pedals
Carling SPST latching On-Off footswitch. Used in Fender etc. Reverb/tremolo/channel switching pedals, (110-P).
$7.95
Knob - Chicken Head, Zonk Style, Set Screw
Colors Available:
High quality chicken head knobs that resemble the style of knob found on the Zonk Machine II and Shatterbox fuzz pedals. The Zonk chicken head knob has a contoured center band with a textured finish. The outer dome has a shiny finish offering a visual contrast. Fits 0.25” (6.35mm) shafts with set screw and brass insert.
  • Height: 0.75 in.
  • Length: 1.065 in.
  • Fits ¼" shaft with set screw
$0.99
Knob - Rogan, RB-67 Series, Medium, Skirted
Colors Available:
High-quality USA made knobs from Rogan Corp. These medium knobs feature a metal insert, spun aluminum inlay, and a skirt with an infilled arrow indicator. The RB-67 Series from Rogan is popularly used on Buchla 200 Series modular synthesizers and can be found on many contemporary eurorack synthesizers..
  • Height: 0.77 in.
  • Diameter: 1.15 in.
  • Fits ¼" shaft with set screws

A variety of sizes and colors are available from the RB-67 Series. See the links below for the full selection of knobs from this series. P-K770-X Small P-K770S-X Small Skirted P-K771S-X Medium Skirted P-K772S-B Large Skirted
$4.25
Switch - Carling, Mini Toggle, SPDT, 3 Position, Solder Lug
Carling mini-toggle switch, SPDT, Solder Lug, 3-Position, On/Off/On
$4.95
Potentiometer - Dunlop, 250 kΩ Audio, for Dunlop GCB80
250 kΩ gear shaft pot with an audio taper. Original Dunlop replacement part. Used in the Dunlop GCB80 High Gain Volume Pedal.
$19.95