Enclosures / Chassis

Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Measures 4.77" x 2.58" x 1.41". Add 0.16" to enclosure depth for lid.

Chassis box perfectly suited for effects pedals and other DIY projects.

4.40" x 2.38" x 1.06" D. Equivalent to Hammond P-H1590B.
Add 0.16" to enclosure depth for lid.

1.99″ x 1.99″ x 1.22″ (51mm x 51mm x 31mm) diecast aluminum enclosure. Equivalent to the Hammond P-H1590LBX enclosure. This enclosure is great for tap tempos and other utility pedals.

5.72″ x 4.77″ x 1.55″ (145mm x 121mm x 39mm) diecast aluminum enclosure. Equivalent to the Hammond P-H1590XX enclosure. This large enclosure is great for bigger projects.

Genuine Hammand screws for use with diecast enclosures. These screws fit all Hammond diecast enclosures as well as any 6-32 UNC threaded enclosure. The thread length is 0.375”.

Pre-drilled three knob pedal enclosure made of pressed steel. This large enclosure is a close match to the original enclosures found on various vintage fuzz effects such as the Vox Tone Bender MKIII, Rotosound Fuzz, and Park Fuzz Sound. It features three holes for potentiometers, two top mounted holes for ⅜” jacks, and a footswitch hole. Comes with 4 rubber feet and a pack of mounting screws(packaged separately) for attaching the bottom plate.

• Footswitch Hole Diameter: 0.492 in. (12.5mm)
• Potentiometer Hole Diameter: 0.294 in. (7.47mm)
• Jack Hole Diameter: 0.447 in. (11.35mm)

Rugged, diecast aluminum alloy chassis box. Equivalent to Hammond's P-H1590A.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Short trapezoid shaped Hammond enclosure. This style is reminiscent of vintage fuzz pedals. Screws included. Key Features:

• Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Four 6-32 x 1/2” machine screws secure lid - into factory tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Slanted YY enclosures perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

4.72" x 3.70" x 2.1" (119mm x 94mm x 56mm) diecast aluminum enclosure. Equivalent to the Hammond 1590C enclosure. This enclosure is a taller version of the 1590BB allowing for more vertical space for larger projects.

The Gorva S90 is a high quality powder-coated take on the Hammond 1590BBM size enclosure with a focus on function and design. Features:

• Beveled top and rounded corners for high quality look.
• Tight fit and small gap between the enclosure and lid.
• Undercut boss allows more internal room for more flexible layout.
• Smooth, eggshell-like matte powder coating.
• Add 0.16" to enclosure depth for lid.

Aluminum chassis. 0.04" thick. Dimensions shown are exterior dimensions. Features:

• Spot-welded heavy duty construction
• Natural finish

Does not include cover. See P-H1434-16

Wah pedal enclosure, bottom, and foot-pedal shell and hardware. Enclosure shell & foot pedal are cast aluminum.

The Gorva C65 is a high quality powder-coated take on the Hammond 125B size enclosure with a focus on function and design. Features:

• Slightly beveled top and rounded corners for high quality look.
• Tight fit and small gap between the enclosure and lid.
• Undercut boss allows more internal room for more flexible layout.
• Smooth, eggshell-like matte powder coating.
• Recessed bottom lid

Large 5.709” x 3.37” x 1.933” Hammond 1590J enclosures. This enclosure is a great option for dense builds and is a popular choice for vintage style fuzz pedals with plenty of room for point to point wiring.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
• Dimensions shown are exterior dimensions.
• Add 0.16" to enclosure depth for lid.

Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box. Add 0.16" to enclosure depth for lid.

Fender® style narrow panel Tweed Deluxe™(5E3) chassis.

• Chrome plated steel, .06" thick.
• Screened white lettering
• 8-Pin (Octal) socket holes: 3
• 9-Pin (miniature) socket holes: 2
• Chassis Dimensions: 14 1/2" x 4 1/8" x 2 5/8"

*NOTE*- This chassis has replaced the “ground” switch lettering found on originals with “standby”

YY enclosure finished in a hammered green powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Hammered green powdercoat
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

Part of a limited run of hammered green enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-GN 1590N1/125 P-H1590N1CE-HMT-GN 1590BB P-H1590BBCE-HMT-GN YY P-H-YY-HMT-GN

1590N1 / 125B diecast enclosure finished in a hammered bronze powdercoat. Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.

• 4.77" x 2.58" x 1.41"
• Hammered bronze powdercoat
• Die-Cast Aluminum
• Includes Box, Lid, And Screws
• Similar to Hammond P-H1590N1
• Add 0.16" to enclosure depth for lid.

Part of a limited run of hammered bronze enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-BRZ 1590N1 / 125B P-H1590N1CE-HMT-BRZ 1590BB P-H1590BBCE-HTM-BRZ YY P-H-YY-HMT-BRZ 1590J P-H1590J-HMT-BRZ

1590N1 / 125B diecast enclosure finished in a hammered green powdercoat. Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.

• 4.77" x 2.58" x 1.41"
• Hammered green powdercoat
• Die-Cast Aluminum
• Includes Box, Lid, And Screws
• Similar to Hammond P-H1590N1
• Add 0.16" to enclosure depth for lid.

Part of a limited run of hammered green enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-GN 1590N1/125 P-H1590N1CE-HMT-GN 1590BB P-H1590BBCE-HMT-GN YY P-H-YY-HMT-GN

YY enclosure finished in a hammered bronze powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Hammered bronze powdercoat
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

Part of a limited run of hammered bronze enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-BRZ 1590N1 / 125B P-H1590N1CE-HMT-BRZ 1590BB P-H1590BBCE-HTM-BRZ YY P-H-YY-HMT-BRZ 1590J P-H1590J-HMT-BRZ