Enclosures / Chassis

Hammond Chassis Box, Aluminum, 16 in. x 8 in. x 3 in. Spot-welded heavy duty construction, natural finish. See P-H1434-26 for cover.

The Gorva Design M45 enclosure has similar dimensions to 1590A but a bit larger for practical use. It measures 100mm [3.94"] x 45mm [1.77"] x 35 mm [1.38"]. The extended dimensions allow for easier builds and top mounted jacks. Features:

• Slightly beveled top and rounded corners for a high quality look.
• Tight fit and small gap between the enclosure and lid.
• Undercut boss allows more internal room for a more flexible layout.
• Smooth, eggshell-like matte powder coating.
• Recessed bottom lid

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Hammond manufacturing 20 gauge steel cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes ⅛" holes to allow installation of optional bottom plates).

Hammond Mfg 20 gauge steel 10” x 6” cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes 1/8" holes to allow installation of optional bottom plates).

Rugged, diecast aluminum alloy chassis box. Equivalent to Hammond's P-H1590A.

Aluminum chassis. 0.04" thick. Dimensions shown are exterior dimensions.

• Dimensions shown are exterior dimensions.
• For use with the P-H1441 and P-H1444 series chassis.
• Four self-tapping screws included.

Hammond extruded aluminum enclosure, blue anodized finish. This genuine Hammond enclosure is great for a wide variety of projects from effects pedals to small preamp/compressor builds. Internal slots make this enclosure ideal for projects that will have multiple pc boards mounted internally.

• Designed to house P.C. boards or for equipment interfacing.
• Sized for standard Eurocards.
• P.C.

Round metal handle with 5" mounting centers and 1.5" height. These handles are great for amplifiers, rackmount gear, and guitar pedals. Mounting screws and lock washers are included. Features

• Made of round steel
• 2 Screws - Panhead 10-32 x 1/2"
• 2 Internal Tooth Lockwashers

Hammond manufacturing 20 gauge steel cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes ⅛" holes to allow installation of optional bottom plates).

YY enclosure finished in a hammered green powdercoat. The slanted YY enclosures are perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features

• Vintage style slant
• Hammered green powdercoat
• Flat top-section for mounting controls
• Recessed lid
• Thick diecast construction

Part of a limited run of hammered green enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-GN 1590N1/125 P-H1590N1CE-HMT-GN 1590BB P-H1590BBCE-HMT-GN YY P-H-YY-HMT-GN

Spot welded heavy duty construction chassis. 0.036" thick. Dimensions shown are exterior dimensions. Chassis box 17 inch wide by 4 inch deep by 3 inch tall.

• Spot welded steel - heavy duty construction chassis.
• Finished in ASA 61 smooth grey or satin black powder paint
• Optional bottom plates are punched with 4 holes – 3/16" diameter (Chassis requires drilling to install optional bottom plates).

Type Chassis Bottom Steel Grey P-H1441-20 P-H1431-20 Steel Black Satin P-H1441-20BK3

Hammond black top and blue case sloped aluminum console. 10 inches wide by 5.5 inch depth. Front of console is 1.1 inches high and rear is 3 inches high. Features:

• Aluminum cases 0.081" thick aluminum
• Pre-assembled with a textured blue case and a black top panel.
• Comes with self adhesive rubber feet and required mounting hardware

Round metal handle with 3.5" mounting centers and 1.5" height. These handles are great for amplifiers, rackmount gear, and guitar pedals. Mounting screws and lock washers are included. Features

• Made of round steel
• 2 Screws - Panhead 8-32 x 1/2"
• 2 Internal Tooth Lockwashers

Walnut chassis with aluminum top panel. Measures 13" x 10" x 3".

• Heavy duty construction walnut chassis.
• Top panel in natural aluminium.
• Walnut chassis is 0.778 inches thick (19.8 mm) - corners are produced with wood bracing. Designed to handle heavy components.
• Top panel is aluminum for easy modification and thick enough to support heavy transformers without bowing - 0.08" (2 mm) thick. Fully 'framed' support from walnut chassis.
• Includes four large round rubber feet (0.75" dia.

20 gauge. Cover for chassis box 17 inch wide by 4 inch deep by 3 inch tall.

• Spot welded steel - heavy duty construction chassis.
• Finished in ASA 61 smooth grey or satin black powder paint
• Optional bottom plates are punched with 4 holes – 3/16" diameter (Chassis requires drilling to install optional bottom plates).

Type Chassis Bottom Steel Grey P-H1441-20 P-H1431-20 Steel Black Satin P-H1441-20BK3

Hammond utility enclosure, 0.04" thick aluminum. 17 inch length by 4 inch width by 3 inch height. Features:

• Four self-tapping screws included
• ASA 61 grey baked powder paint

Aluminum chassis. 0.04" thick. Dimensions shown are exterior dimensions.

• Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
• Vibra finished for a smooth surface with no sharp edges.
• Four 6-32 x ½" machine screws secure lid - into tapped holes.
• Designed to meet IP54.
• Low side wall draft angle (2 degrees or less) for easy P.C.

Fender® style narrow panel Tweed Princeton™(5F2) chassis.

• Chrome plated steel, .06" thick.
• Screened white lettering
• 8-Pin (Octal) socket holes: 2
• 9-Pin (miniature) socket holes: 1
• Chassis Dimensions: 13-3/4" x 4-1/8 x 2-1/2"

1591T Series enclosure made of clear polycarbonate. The 1591C is a similar size to the 1590N1 / 125B diecast aluminum enclosures. Includes four cover screws and pre-installed brass inserts.

• Ideally suited for mounting printed circuit boards.
• Perfect for applications where parts, sensors or indicators need to be visible.
• Crystal Clear version is almost totally transparent.
• Integral card guides accept 1.5 mm (0.062”) P.C. cards.
• Lap joint construction provides protection against access of dust and splashing water.
• Designed to meet IP54.
• Molded from flame retardant, easy to machine, translucent polycarbonate (material carries a UL flammability rating of 94V-2).
• Lid is secured with M3 x 10 mm Phillips machine screws, threaded into integral brass bushings.

Hammond manufacturing 20 gauge steel cover plate. Punched with 4 holes – 3/16” diameter (Chassis now includes ⅛" holes to allow installation of optional bottom plates).

1590N1 / 125B diecast enclosure finished in a hammered green powdercoat. Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.

• 4.77" x 2.58" x 1.41"
• Hammered green powdercoat
• Die-Cast Aluminum
• Includes Box, Lid, And Screws
• Similar to Hammond P-H1590N1
• Add 0.16" to enclosure depth for lid.

Part of a limited run of hammered green enclosures which includes: Enclosure SKU 1590B P-H1590BCE-HMT-GN 1590N1/125 P-H1590N1CE-HMT-GN 1590BB P-H1590BBCE-HMT-GN YY P-H-YY-HMT-GN