Enclosures / Chassis
Chassis - Mod®, Buzzaround, Pre-drilled, Hammered Dark Gray
Pre-drilled vintage style pedal enclosure by Mod® Electronics. The shape of this folded steel enclosure is inspired by the original Burns Buzzaround enclosures and is pre-drilled to match the original layout of the Buzzaround pedal. The hammered dark gray powder coat provides a close match for the original appearance but will hold up much better than the paint found on the vintage pedals.
$74.95
Enclosure - Wah Pedal Shell and Hardware
Wah pedal enclosure, bottom, and foot-pedal shell and hardware. Enclosure shell & foot pedal are cast aluminum.
$40.00
Chassis Box - GØRVA Design, C65, Diecast, 4.72” x 2.56” x 1.54”
The Gorva C65 is a high quality powder-coated take on the Hammond 125B size enclosure with a focus on function and design. Features:
Colors Available:
- Slightly beveled top and rounded corners for high quality look.
- Tight fit and small gap between the enclosure and lid.
- Undercut boss allows more internal room for more flexible layout.
- Smooth, eggshell-like matte powder coating.
- Recessed bottom lid
Starting at $10.45
Chassis Box - 1590N1 / 125B, Diecast, 4.77" x 2.58" x 1.41"
Equivalent to Hammond P-H1590N1. Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Measures 4.77" x 2.58" x 1.41". Add 0.16" to enclosure depth for lid.
Colors Available:
Measures 4.77" x 2.58" x 1.41". Add 0.16" to enclosure depth for lid.
Starting at $7.25
Chassis Box - 1590BB, Diecast, 4.71" x 3.70" x 1.18", Predrilled
Predrilled 1590BB enclosures. Measures 4.71" x 3.70" x 1.18" deep. These enclosures come drilled with holes for pots, footswitch and top mounted jacks.
Colors Available:
- Standard size footswitch mounting hole fits 12mm or 15/32” bushings
- ⅜” mounting holes for top mounted jacks
- Enclosed or low profile ¼” jacks recommended
- Top mounted DC jack mounting hole fits common switched jacks such as S-H750-X and P-JBLB-IN-S
- 8mm potentiometer mounting holes fit a variety of different pot sizes but 16mm pots are recommended.
Starting at $9.95
Screw - Hammond, Phillips, Countersunk, 6-32 UNC
Genuine Hammand screws for use with diecast enclosures. These screws fit all Hammond diecast enclosures as well as any 6-32 UNC threaded enclosure. The thread length is 0.375”.
Colors Available:
Starting at $1.35
package of 4
Chassis Box - Hammond, 1590X, Diecast, 5.72" x 4.77" x 2.06"
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$17.40
Chassis Box - 1590BS, Diecast, 4.40" x 2.38" x 1.65"
4.40" x 2.38" x 1.65" (112mm x 61m x 42mm) diecast aluminum enclosure. Equivalent to the Hammond 1590BS enclosure. This enclosure is a taller version of the 1590B allowing for top mounted jack and more overall area for larger projects.
$6.95
Chassis Box - Hammond, 1590G, Diecast, 3.94" x 1.97" x 0.83"
Add 0.16" to enclosure depth for lid.
Special Order Item
Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure. Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding. Vibra finished for a smooth surface with no sharp edges. Four 6-32 x 1/2" machine screws secure lid - into tapped holes. Designed to meet IP54. Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.Add 0.16" to enclosure depth for lid.
$8.73
Out of Stock
Chassis Box - Hammond, 1590A, Diecast, 3.64" x 1.52" x 1.06"
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$7.55
Chassis Box - 1590LB, Diecast, 1.99″ x 1.99″ x 1.22″
1.99″ x 1.99″ x 1.22″ (51mm x 51mm x 31mm) diecast aluminum enclosure. Equivalent to the Hammond P-H1590LBX enclosure. This enclosure is great for tap tempos and other utility pedals.
$3.95
Chassis Box - Hammond, 1590BB, Diecast, 4.71" x 3.70" x 1.18"
Colors Available:
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
Starting at $10.95
Chassis Box - YY, Diecast, Slanted, 4.65" x 3.70" x 1.66"
Slanted YY enclosures perfect for fuzz pedals and other vintage style effects. In addition to the classic slant, this enclosure features thick diecast walls and a recessed bottom cover. The four bottom plate cover screws are included. Features
Colors Available:
- Vintage style slant
- Flat top-section for mounting controls
- Recessed lid
- Thick diecast construction
Starting at $23.95
Chassis Box - Hammond, 1590DD, Diecast, 7.40" x 4.72" x 1.30"
Hammond Mfg. Diecast Aluminum Chassis Box – 7.4” x 4.7” x 1.3”. Made in Taiwan. Key Features: • Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
$20.25
Chassis Box - 1590B, Diecast, 4.40" x 2.38" x 1.06"
4.40" x 2.38" x 1.06" D. Equivalent to Hammond P-H1590B.
Add 0.16" to enclosure depth for lid.
Colors Available:
Add 0.16" to enclosure depth for lid.
Starting at $5.95
Chassis - Three Knob Fuzz, Pressed Steel
Pre-drilled three knob pedal enclosure made of pressed steel. This large enclosure is a close match to the original enclosures found on various vintage fuzz effects such as the Vox Tone Bender MKIII, Rotosound Fuzz, and Park Fuzz Sound. It features three holes for potentiometers, two top mounted holes for ⅜” jacks, and a footswitch hole. Comes with 4 rubber feet and a pack of mounting screws(packaged separately) for attaching the bottom plate.
- Footswitch Hole Diameter: 0.492 in. (12.5mm)
- Potentiometer Hole Diameter: 0.294 in. (7.47mm)
- Jack Hole Diameter: 0.447 in. (11.35mm)
$19.95
Chassis Box - Hammond, 1590B3, Diecast, 4.57" x 3.03" x 1.32"
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Dimensions shown are exterior dimensions.
- Add 0.16" to enclosure depth for lid.
$10.80
Chassis Box - Hammond, 1590D, Diecast, 7.39" x 4.71" x 2.05"
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Six 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C.
$23.45
Chassis Box - Hammond, 27969PSLA, Eddystone 1590A, Diecast, 3.6” x 1.5” x 1.2”
Eddystone 27969PSLA enclosure with similar dimensions to the Hammond 1590A enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590A style builds.
- Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
- Aluminum alloy to BS1490, LM2M - supplied in natural finish.
- Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
- Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
- Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
- Countersunk lid holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
$11.95
Chassis Box - 1590G2, Diecast, 3.94" x 1.97" x 1.06"
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Four 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Dimensions shown are exterior dimensions.
- Add 0.16" to enclosure depth for lid.
$9.65
Chassis Box - Hammond, 1590F, Diecast, 7.40" x 7.40" x 2.48"
- Rugged, diecast aluminum alloy (tough yet easy to machine), electronic instrument enclosure.
- Lap joint construction provides protection against access of dust and splashing water. Also provides for improved EMI/RFI shielding.
- Vibra finished for a smooth surface with no sharp edges.
- Six 6-32 x ½" machine screws secure lid - into tapped holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
- Dimensions shown are exterior dimensions.
$33.10
Chassis Box - Hammond, 26827PSLA, Eddystone 1590D, Diecast, 7.4” x 4.7” x 2.2”
Eddystone 26827PSLA enclosure with similar dimensions to the Hammond 1590D enclosure. The Eddystone version has sharper corners for a distinctive appearance. This enclosure is a great option for 1590D style builds.
- Rugged, diecast aluminum alloy (tough - yet easy to machine), electronic instrument enclosure.
- Aluminum alloy to BS1490, LM2M - supplied in natural finish.
- Eddystone designed. The Eddystone brand was purchased by Hammond in 1998.
- Lap joint construction provides protection against access of dust and splashing water. Also provides excellent EMC performance.
- Lids are retained by M3.5 x 12 countersunk screws (POZIDRIV No. 2 head).
- Countersunk lid holes.
- Designed to meet IP54.
- Low side wall draft angle (2 degrees or less) for easy P.C. board mounting.
$28.95
Chassis Box - 1032L, Diecast, Looper, 10" x 2.75" x 1.89"
Extra long diecast aluminum chassis commonly used for looper/loop-switching pedals. This enclosure style is often referred to as the 1032L. Mounting screws for the bottom plate are included with this chassis box. Add 0.16" to enclosure depth for lid.
$10.99
Chassis Box - Hammond, 1590N1, Diecast, 4.77" x 2.58" x 1.41"
Depending on the manufacturer, this enclosure is usually very similar to a 125B.
Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.
Add 0.16" to enclosure depth for lid.
Aluminum enclosure with countersunk lid that machine screws into drilled and tapped holes. Lap joint construction provides protection from dust and water. Vibra finished, no sharp edges.
Add 0.16" to enclosure depth for lid.
$12.50