Fan - 115V, AC 50/60 Hz, 1 Phase, low noise

View cart Checkout

Fan Guard - Metal Grill, Finger Guard

Metal finger-protecting guard for P-HFAN.

$3.⁵⁰

Fuse - Fast-Blow, 250V, 3AG, 0.25" x 1.25"

Protect your expensive investment or hobby with inexpensive fuses.

Starting at $2.²⁵

package of 5

Fuse - Slow-Blow, 250V, Miniature, GMD-type 5mm x 20mm

Protect your expensive investment or hobby with inexpensive fuses. Time-delay, low breaking capacity. Rated at 250V. Package of 5

$3.⁹⁵

package of 5

Fuse - Slow-Blow, 250V, 3AG, 0.25" x 1.25"

The 3AG Slo-Blo fuse solves a broad range of application requirements while offering reliable performance and costeffective circuit protection. Fits fuse block S-H259 and fuse holder S-H201.

$3.²⁵

package of 5

Grommet - Rubber, for chassis holes

Listed diameter is inside diameter. Sold in packs of 5.

3/8" diameter designed for chassis hole with diameter 1/2"
1/8" diameter designed for chassis hole with diameter 1/4"
3/16" diameter designed for chassis hole with diameter 5/16"
1/4", small cutout diameter designed for chassis hole with diameter 3/8"
1/4" diameter designed for chassis hole with diameter 7/16"
5/16" diameter designed for chassis hole with diameter 7/16"

Starting at $1.⁷⁵

package of 5

Strain Relief - for ¾" x ~\frac{27}{32}~" hole, ~\frac{5}{16}~" cord diameter

16/3 SJT, 5/16" cord diameter. These one piece Strain Relief Bushings securely anchor, absorb, and protect cables and wires from push/pull and twist forces, while insulating them from irregular or sharp panel edges. They are easily and quickly installed with special installation pliers or other hand or production tools. Black H.S. Nylon, and the temperature index is 105° Centigrade.

$1.²⁹

Strain Relief - for ~\frac{35}{64}~" x ⅝" Hole, ~\frac{11}{32}~" Cord Diameter

For 35/64" x 5/8" chassis hole, 11/32" cord diameter. Fits most Fender® amps.

Protects the lifeline of your electric/ electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord.
Securely anchors, insulates, and protects cables at panel entry points

$0.⁵⁹

Receptacle - IEC C14, for power cord, 3 prong

Plastic IEC C14 connector for power entry. This power receptacle mounts with two screw holes which are counterunk for a clean look when using countersunk screws. This is a 3 prong connector for power cables with ground connections. Internal connections can be soldered into place or used with quick disconnects. See Specifications, Files, and Documents for a datasheet with dimensions and panel cut out sizing.

$2.¹⁵

Receptacle - AC with Fuse Holder, mates with S-W123 & S-W124

I.E.C. Power Cord Receptacle. Mates with power cords S-W123 and S-W124. Rated for 6A, 250V. UL listed. Compatible with GMA fuses

$1.⁸⁵

Fuse Holder - for Marshall, ¼" Fuses

Fuse Holder - High Quality Marshall Snap-In Style (Fits 5/8" to 11/16" Chassis Holes). Suitable for 1/4" fuses. UL and CSA approved. Electrical Specifications:

Rated current: 10A
Rated voltage: 250V AC
Contact resistance: 2MΩ @ 250V DC or less
Dialectric withstand: 1 minute @ 1500V AC
Insulation resistance: 100MΩ or more @ 500V DC

$5.⁹⁹

Dial Lamp - #40, T-3-¼, 6.3V, .15A, Screw Base

Long life general replacement lamps for dials, indicators, etc. Sold in packages of 10.

$3.⁰⁰

package of 10

Dial Lamp - #44, T-3-¼, 6.3V, .25A, Bayonet Base

Long life general replacement lamps for dials, indicators, etc.

$3.⁰⁰

package of 10

Dial Lamp - #46, T-3-¼, 6.3V, .25A, Screw Base

Long life general replacement lamps for dials, indicators, etc. Sold in packages of 10.

$3.⁰⁰

package of 10

Dial Lamp - #47, T-3-¼, 6.3V, 0.15A, Bayonet Base

Long life general replacement lamps for dials, indicators, etc. The #47 bulb is the most common replacement light used today. Used on the vast majority of Fender amps and many others as well.

$4.⁵⁰

package of 10