Generator - Lodestar, RF Signal generator

Item Unavailable

Sorry! You are trying to check out one of our items which is no longer available. Why not check out one of these alternate options?

Jumper Test Lead Set - Clip 35mm, Total Length 24", 22AWG
Package of 10
Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green
$4.89
Bias Master™ - TAD, tube tester, with 4 probes
Bias Master™ system BM4 Measures Bias current of the vacuum tubes in your amp. Includes 4 probes and english/german operation manual. The Bias Master™ allows you to monitor the bias current safely and easily. While adjusting the Bias control pot of your amp, the Bias Master™ shows the actual result. This lets you set and evaluate the full reasonable biasing range your amp and tubes offer to find and set your personal perfect choice.
$228.95
Probes - TAD, for Bias Master™, set of 2
Package of 2
Bias Master™ set of adapter probes for testing other types of tubes. For use with the S-TBM4-X Bias Master™ system.
Starting at $65.95
Digital Capacitance Meter - YF-150, 9 ranges
Nine ranges give precision readings from 0.1 pF to 20,000 µF. Can be used to check virtually all capacitors for tolerance value, selecting matched sets, etc.
  • 0.1 pf to 20,000 μF, 9 ranges
  • Over range indicator
  • 0.5% basic accuracy
  • Tilt stand
  • 3-1/2 digit LCD, 1" h x 2-¼" w
  • 1.5" x 2.8" x 6"
  • Zero adjustment
  • Input protected
  • Low battery indicator
  • Includes case, leads, battery, spare fuse and instructions
$49.95
Digital Multimeter - YF-3220, multi-purpose
Ergonomically designed. Uses one 9V battery, included.
  • 0.5% basic DC accuracy
  • audible continuity test
  • 3 1/2 digit LCD, 0.625" high
  • 10M ohm input resistance
  • 1.5" x 3" x 7.5"(w/o rubber case)
  • overload protection
  • voltage to 1000VDC, 750VAC
  • capacitance to 20 microfarads
  • polarity indicator
  • frequency to 10MHz
  • over range indicator
  • 10A (AC or DC)
  • low battery indicator
  • hFE and diode test
  • tilt stand and case
$49.95
Generator - Lodestar, Audio Frequency
The oscillation frequency range of this audio generator is between voice frequency band and super voice frequency band. Square and sine wave. 10K ohm input impedance, 10 V rms maximum input voltage. 600 ohm output impedance. Equipped with synchronized input terminals, enabling the high power output signas to be accurately controlled by small signals. comes with test lead and ground lead. 5.9" high x 9.8" wide x 5.1"deep.
$205.95
Heat Sink - dissipate heat during soldering
Temporary Heat Sink. Absorb & dissipate heat during soldering/desoldering sensitive parts. Made in Taiwan.
$2.45
Solder wick - GC Braid, multiple sizes
5 foot long desoldering braid. Great for removing solder from printed circuit boards or other electronic equipment.
Starting at $3.95
Tolex Glue - Brush-on adhesive for applying tolex
Brush-on adhesive ideal for applying tolex. Cleans up with soap and water. No nasty solvents required. Does not stretch or shrink the vinyl. Comes in quarts or gallons. Specifications: Tolex Glue is a non-flammable, Neoprene based, water borne adhesive formulated to bond tolex and vinyl to wood and wood based substrates. Min. use temp: 45°F Freezes at 32°F and lower Shelf Life: 6 Months Directions: Surfaces to be bonded must be clean. Apply a very thin coat to both surfaces. Very porous surfaces may require more than one coat. Second coat should not be applied until first has dried. Allow to 'flash off' for 20-30 minutes. Cloudy areas indicate incomplete drying. This time can be shortened with forced air and/or heat. Position pieces carefully prior to bringing surfaces together as bond is made instantly.
Starting at $32.95
StripBoard - Single Sided, 3.04” x 1.55”, Vintage Spacing
Colors Available:
Stripboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has a 20x10 grid (10 strips) and easily fits into 1590BB style enclosures and larger vintage-style fuzz enclosures. Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:
  • High-quality 1.6mm FR4 glass-epoxy circuit board
  • 1oz/ft2 copper weight
  • HASL coated strips
  • 20 x 10 holes (10 strips)
  • 3.04” x 1.55”
$2.95
Adjustment Tool - Bourns Trimpots, H-90
Bourns trimmer adjustment tool. This tool is compatible with both the R-VT96Y-X multiturn trimmers and the R-VT62P-X single turn trimmers. The recessed end is especially helpful when used with the 3296Y trimmers to avoid slipping off of the screw adjuster. Features
  • Meets UL 94V-0
  • Pocket clip
  • For use on most trimmer shafts/rotors
  • Recessed end for use with extended shafts
  • RoHS compliant
$4.95
Solder - Kester, 60 / 40, 44 Flux, 1 lb spool
60/40 Rosin Core, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.
Starting at $49.95
Tool - Precision Devices, Lead Former, Various Sizes
High quality, made in USA lead formers. These are great tools for bending component leads to fit various footprints. The radiused ends provide a right angle bend that does not stress the metal lead. These lead formers are made of high impact ABS plastic.
$4.95
Solder - Kester, 60 / 40, 44 Flux, 66 Core, .031 Dia, .5 oz
Kester 44 60/40 rosin core type. .031" diameter, 0.5 oz
$6.95
Tool - Slotted Nut Driver, for Qingpu Jacks
Simple and easy to use nut driving tool for the slotted nuts found on Qingpu jacks that are commonly used in Eurorack modules. The tool anchors into the sleeve of the jack ensuring no slippage when in use, protecting the faceplate from accidental damage. The two grip holes are cut to the size of M2.5 and M3 hex nuts and can be used in a pinch to tighten nuts of those sizes, or to hang your tool on a keyring! One side of the tool works with Mod "Top Brass" nuts and slotted W-QP-NUT-K nuts used on W-QP-518MA, W-QP-419GR, and W-QP-518MA-BM. The other side works with slotted W-QP-NUT-PJ-R nuts used on W-QP-PJ3410. Either side will work with Befaco Bananuts for 3.5mm jacks (W-BNUT-X). The nut driving tool is made of steel.
$4.25
The Nibbler - cutter for square holes
Instructions
  • Simply drill 3/8" hole insert cutting head and compress handles.
  • Gives you the ability to make square holes for fuse holders, special connectors displays etc.
  1. Material to be nibbled is placed in the gap between the punch and blade channel.
  2. By squeezing the handles together, the punch will move down into the channel, cutting out a slug of metal.
  3. A scribe line can be followed by looking down on work in this position.
$6.95